Advertisement
24G-2 F URNACE
two lower sink module mounting bolts (front
lower right).
Tighten two screws located at
front lower left of module .. Connect courtesy
lamp wiring clip to transition on furnace .
4. Install cupboard partition behind sink
trap .
Connect water lines at sink faucet .
Install sink trap .
5 . Connect all ducts to furnace.
6 . Connect
L .P .
gas supply line to furnace .
7 . Connect furnace electrical connector .
8 . Install furnace fuse in living area fuse
block .
9 . Turn on
L .P .
gas at tank . Check for L .P .
gas leaks at furnace and correct as necessary.
Then check furnace for proper operation .
10 . Install any remaining furniture compo-
nents, such as : Davo, swivel chair trim panels,
and lower shelf to left of furnace .
11 . Check furnace for proper operation.
MODEL ZE06582
REMOVAL
1 . Shut off L .P . gas at L .P . tank .
2 . Disconnect living area battery negative
(-} cable from battery .
3. Remove
range/oven
as
described
in
Maintenance Manual X-7525 (Section 24H) .
4. Unplug electrical power converter from
120-volt outlet .
5 . Disconnect converter
12-volt positive
lead from circuit breaker and negative lead
from body structural member.
6 . Remove
converter
and
converter
mounting bracket.
Refer to Section 24B of
this supplement for details.
7 . Remove the follo
eners :
sink module fast-
A . Three screws retaining sink module to
bath module .
B . Bolt and spacer located at the rear
middle of sink module.
Use care when
removing bolt to avoid dropping spac
located between sink module and outer
wall of vehicle.
C. Two bolts at floor level beside furnace .
NOTE:
S i
forward end.
is still attached at
8 . Carefully pull furnace end of sink module
about one inch away from outer wall .
9 . Remove
L .P .
gas line that goes to both
range/oven and, furnace (fitting located at
floor level on the left-side of furnace .
10 . Disconnect furnace electrical connector .
11 . Disconnect all ducts from furnace .
12 . Remove furnace plenum from unit.
13 . Remove furnace to floor mounting bolts
and four screws
located
at
top back
of
furnace .
14 . Slide furnace toward center of vehicle
until vents on furnace clear vent tubes on
vehicle outer wall .
Then remove furnace
through the range/oven opening .
INSTALLATION
1 . Position furnace in sink module through
range/oven opening . Be sure vents in back of
furnace are aligned with vent tubes in outer
wall of vehicle .
Then slide furnace outward,
being sure furnace vents are engaged in the
vent tubes.
2 . Install furnace to floor mounting bolts
and
four screws
located
at
top
back
of
furnace .
3 . Install furnace plenum on unit .
4 . Connect all ducts to furnace .
5 . Connect L .P . gas supply line to floor
fitting and furnace.
6 . Connect furnace electrical connector.
back into position
nstall the following
7 . Slide
sink module
against outer wall . Then
module fasteners :
A . Bolt and
spacer located at the rear
middle of sink module .
B . Three screws retaining sink module to
both module.
C . Two bolts at floor level beside furnace .
8 . Install converter and converter mounting
bracket .
Also
connect
converter
12-volt
positive lead to circuit breaker and negative
lead to body structural member .
Plug con-
verter cord into 120-volt outlet .
9 . Install range/oven as described in Main-
tenance Manual X-7525 (SECTION 24H).
10 . Turn on L .P . gas at tank. Check for L .P .
gas leaks at furnace and range/oven. Correct
as necessary.
11 . Connect living area battery negative (-}
cable to battery .
12 . Check furnace for proper operation .
Advertisement
