Subscribe to Our Youtube Channel
Related Manuals for Anest Iwata iCon-M233N
Summary of Contents for Anest Iwata iCon-M233N
- Page 1 General Industry PUMPS MIDDLE - HIGH PRESSURE RANGE M233N MULTI SPRAY PUMP A233N AIRLESS PUMP USER’S INSTRUCTION MANUAL...
- Page 2 iCon-A233N...
- Page 3 INDEX ......4 .. 24 ..44...
-
Page 4: Safety Warning
Be sure to observe warnings and cautions in this instruction manual. If not, it can cause paint ejection and serious bodily injury by drawing organic solvent. ANEST IWATA ICON Pump Unit complies to ATEX regulations 2014/34/EU; • Protection level: II 2G T6 •... -
Page 5: Other Precautions
If you feel something wrong, consult a medical doctor immediately. The noise level of ANEST IWATA Spray Gun doesn’t exceed the 85 dB (A) A-weighted sound pressure value about the risk of daily exposure to noise. THE USE OF INDIVIDUAL HEARING PROTECTION IS ALWAYS RECOMMENDED, because the terms of use and the influence of other noises in the job area, could increase the average value allowed. - Page 6 MULTI SPRAY Pumps CONFIGURATION ICON M233N-S ICON M233N-H Pump Unit mounted on CART with SUCTION HOSE SET Pump Unit mounted on CART with Gravity HOPPER SET ICON M233N-SWM ICON M233N-HWM Pump Unit mounted on WALL MOUNT with SUCTION HOSE SET...
- Page 7 AIRLESS Pumps CONFIGURATION ICON A233N-S ICON A233N-H Pump Unit mounted on CART with SUCTION HOSE SET Pump Unit mounted on CART with Gravity HOPPER SET ICON A233N-SWM ICON A233N-HWM Pump Unit mounted on WALL MOUNT with SUCTION HOSE SET...
-
Page 8: Technical Data
SERIAL NO. XE 30:1 RATIO 2019 MANUFACTURED MADE IN ITALY Manufacturing date Serial Number ANEST IWATA Strategic Center Via degli Aceri 1, Cardano al Campo (VA) Italy CE Marking - ATEX Marking • II 2 G T 6 X •... -
Page 9: Box Content
6. BOX CONTENT When receive and before using the Pump, make sure that it has not been damaged during transport or storage. Also check that all the following standard components are inside the packaging. MULTI SPRAY or AIRLESS UNIT, mounted on Cart Frame... -
Page 10: Installation
CAREFULLY READ AND OBSERVE SAFETY WARNING OF THE INSTRUCTIONL OF THE SPRAY GUNS TO BE USED. ICON-M233N: MSGS-200 EVO / ICON-A233N: ALG7 TE BEFORE INSTALLATION SET THE AIR AND FLUID REGULATORS TO 0 bar. MOVING PARTS OF THE PUMP COULD CUT OFF THE FINGERS OR SERIOUSLY INJU- RE THE HUMAN BODY. -
Page 11: Unit Configuration
7.3 UNIT CONFIGURATION Air pressure regulator set Air motor set OPTIONAL ICON-M233N ICON-A233N ---- MSGS-200 EVO ALG-7 TE MAIN CONFIGURATION A Air motor Pressure regulator (for spray gun) PLUNGER PUMP B Fluid pump L Pressure regulator (for pump) -
Page 12: Safety Systems
INSIDE THE PUMP WILL BE RELEASED. STOP 9. WORKABLE PRODUCTS ANEST IWATA ICON PUMPS ARE CONCEIVED TO PAINT FERROUS MATERIAL IN GENERAL, WOOD AND PLASTIC. WARNING TO USE THE EQUIPMENT WITH SPECIAL PRODUCTS ASK FOR THE APPROVAL OF THE MANUFACTURER. - Page 13 10.1 FLUSHING BEFORE USING ATTENTION! THE PUMP MUST BE CLEANED BEFORE USING IT FOR THE FIRST TIME, AFTER WORKING AND AFTER ANY COLOUR CHANGE. After installation (chapt. 7), before to supply air to the pump, confirm Immerse the suction hose in the contai- that the ball valve is open and the air regulator is adjusted to 0 bar.
- Page 14 10.2 USE IMPORTANT! BEFORE USE of the pump it is IMPORTANT TO READ CAREFULLY and observe the war- nings and cautions contained in THE INSTRUCTION MANUAL OF THE GUN TO BE USE. MSGS-200 EVO (with Multi Spray Pump) or ALG-7 TE (with Airless Pump).
-
Page 15: Monthly Maintenance
THE ICON X3 PUMP HAS BEEN DESI- GNED TO WORK WITH PAINTS WITHOUT THE NEED FOR LUBRICANT. HOWEVER, IN CASE OF INTENSIVE USE, IT IS ADVISABLE TO ADD THE ANEST IWATA LUBRICANT (94445770 - NOT INCLUDED) INTO THE PACKING HOLDER TO EXTEND THE LIFE OF THE... - Page 16 Ref. Code 94444790 940085A0 940052A0...
- Page 17 Ref. Code 94444790 940085A0 940052A0...
- Page 18 12.1 PLUNGER PUMP SET Ref. Code 940000A0 940093A0 940094A0 12.2 FLUID PUMP SET Ref. Code 940032A0 Ref. Code 940070A0 04944770 940033A0...
- Page 19 12.3 AIR MOTOR SET Ref. Code Ref. Code 940073A0 PILOT VALVE SET 940007A0 PILOT VALVE CAP 940004A0 940008A0 940005A0 940002A0 METAL 04447820 T-JOINT 940072A0...
-
Page 20: Air Regulator Set
12.4 AIR REGULATOR SET AIR REGULATOR SET CART FRAME WALL MOUNT Version Version AIR REGULATOR SET for Airless Units CART FRAME WALL MOUNT Version Version Ref. Code Q.ty M233N A233N L-JOINT NIPPLE 02004003 T-JOINT... -
Page 21: Suction Hose Set
12.5 DELIVERY PAINT FILTER TF-1S Ref. Code 940053A0 940054A0 940055A0 SWIVEL JOINT JOINT 12.6 SUCTION HOSE SET Ref. Code 00407203 12.7 CART FRAME SET Ref. Code SPLIT PIN 940089A0 CONNECTION ELEMENT... -
Page 22: Troubleshooting
13. TROUBLE SHOOTING INCONVENIENCE CAUSE CHECK SOLUTION The air pressure does not increase The paint does not flow out of the gun The pump does not work The pump does not stop. - Page 23 13. TROUBLE SHOOTING INCONVENIENCE CAUSE CHECK SOLUTION The pump does not stop The spray-fan size keeps chan- ging The indicator of pressure gauge indicates the pre- sence of pressure even though the air regulator is closed.
- Page 24 Sidney - AUSTRALIA info@anest-iwata-it.com info@anest-iwata.com.au www.anest-iwata.it www.anest-iwata.com.au ANEST IWATA Deutschland GmbH SOUTH AFRICA Leipzig - GERMANY info@anest-iwata-de.com ANEST IWATA South Africa Pty Ltd. www.anest-iwata.de Johannesburg - REPUBLIC OF SOUTH AFRICA www.anest-iwata.co.za ANEST IWATA France S.A. FRANCE info@anest-iwata-fr.com ASIA www.anest-iwata.fr Yokohama - JAPAN ANEST IWATA U.K.
Need help?
Do you have a question about the iCon-M233N and is the answer not in the manual?
Questions and answers