Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Acromag IP220 Series
Summary of Contents for Acromag IP220 Series
- Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
- Page 2 12-Bit High-Density Analog Output Board USER'S MANUAL ACROMAG INCORPORATED 30765 South Wixom Road P.O. BOX 437 Wixom, MI 48393-7037 U.S.A. Tel: (248) 624-1541 Fax: (248) 624-9234 Copyright 1994,1996 Acromag, Inc., Printed in the USA. Data and specifications are subject to change without notice. 8500-486-E98M015...
-
Page 3: Table Of Contents
The information contained in this manual is subject to change DRAWINGS Page without notice. Acromag, Inc. makes no warranty of any kind with 4501-441 IP220 JUMPER LOCATIONS regard to this material, including, but not limited to, the implied 4501-434 IP MECHANICAL ASSEMBLY warranties of merchantability and fitness for a particular purpose. -
Page 4: Industrial I/O Pack Interface Features
OLE-PC, MSDOS format). This software provides individual drivers • 1 6 -bit I/O - Control register writes, DAC writes, and calibration that allow Acromag I/O Packs and the APC8610 carrier to be easily coefficient reads are performed through 16-bit data transfer cycles in the IP module Input/Output space. -
Page 5: Board Configuration
SERIES IP220 INDUSTRIAL I/O PACK -BIT HIGH-DENSITY ANALOG OUTPUT MODULE rise above the maximum operating temperature and to prolong the Analog Output Voltage BOB Data life of the electronics. I f the installation is in an industrial (Volts) (Hex) environment and the board is exposed to environmental air, careful 9.9951 FFFO consideration should be given to air-filtering. -
Page 6: Analog Output Noise And Grounding Considerations
(e.g. 12-bits or more). R e f e r to INTReq0" Drawing 4501-440 for example output and grounding connections. Contact your Acromag representative for information on our many INTReql" isolated signal conditioning products that could be used to provide... -
Page 7: Address Maps
All IP's have . 1 . NOT USED' 'IPAC' (R)-CHO Offset Error (R)-CHO Gain Error (R)-CH1 Offset Error (R)-CH1 Gain Error Acromag ID (R)-CH2 Offset Error Code (R)-CH2 Gain Error 22 IP220-16 IP Model (R)-CH3 Offset Error 23 IP220-8 Code... -
Page 8: Transparent Mode
SERIES IP220 INDUSTRIAL I/O PACK -BIT HIGH-DENSITY ANALOG OUTPUT MODULE (and the updated analog output appears at the board's field The twelve bits of data are left-justified within the 16-bit word connector). The data, of all the channels, is simultaneously (D16). -
Page 9: Using The Transparent Mode
Software calibration uses some fairly complex equations. calibration coefficient data. This data is necessary to adjust, by Acromag provides you with the Industrial I/O Pack Software Library software, the accuracy of the involved channel's analog output. diskette to make communication with the board and calibration easy. -
Page 10: Calibrated Performance
SERIES IP220 INDUSTRIAL I/O PACK -BIT HIGH-DENSITY ANALOG OUTPUT MODULE Using equation (2), one can determine the ideal count for any and gain is important because the worst case uncalibrated error can desired voltage within the range. For example, if it is desired to be significant (although the typical uncalibrated errors observed may output a voltage of +5 Volts, equation (2) retums the result 3072 for be much less). -
Page 11: 4.0 Theory Of Operation
It is highly recommended that a non-functioning example analog output and grounding connections. board be returned to Acromag for repair. The board can be damaged unless special SMT repair and service tools are used. Further, Acromag has automated test equipment that thoroughly The fully populated board contains sixteen 12-bit DAC's (IP220- 16), one per channel. -
Page 12: Specifications 1
Maximum corrected error (i.e. REMOVING OR INSERTING BOARDS calibrated) at 25°C (See Note 5) with the output unloaded. Acromag's Applications Engineers can provide further technical Settling Time8 to within 0.012% for a 20V assistance if required. When needed, complete repair services are step change (load of 5KLI in also available from Acromag. - Page 13 (per MIL-G-45204, Type II, Grade C). be kept to a minimum to reduce noise and power loss. Connects to Acromag termination panel 5025-552 from the rear Cable: 50-wire flat ribbon cable, 28 gage. Non-Shielded cable of the card cage via flat 50-pin ribbon cable (cable Model model uses Acromag Part 2002-211 (3M Type C3365/50 or 5025-550-X or 5025-551-X).
- Page 14 I/O INTERFACE LOGIC INTERFACE 1 W r i l . A N N _I 44 I I I II I COMPONENT SIDE VIEW 0212! ALMNI.LA A A A POWER SUPPLY SELECTIONS (PINS OF J1 AND J2) . . r 2 POWER supply SELECTION' (I k 2)
- Page 15 1P2241 CARRIER c o o p *soma' •CTIR V.15 LOM) • C*17 • SEE NOTE 2 L O W / 7 1 7 C1115 • SEE NOTE 4 LOAD 15 'LEAD DO. SUPPLY - SuppLV • (ARM GROUND CC•ANECL.044 Al 4014E1.
- Page 16 4 0 1 6 9 5 3 5 / 9 6 6 8 1100E1 5 0 7 5 - 5 5 7 0 4 . 4 9 6 8 BOARD u o '7 riNNwp, ON _.NANEL B. C . 0 0 0 ( ' C r ) TOP VIEW 5 0 - R N...
- Page 17 /6/ RA6 DIN NOUPOING SHOWN HERE OIN ( I I 5 6 4 3 6 324tert 141644441011 PANEL ACROMAG PAIN NU16ER 4 9 4 1 - 8 4 4 /7/ RAIL 9114 MOUNTING 34632 SHP/MK-NE M I FM 58922, 354NN ( 7 7 4 ) SMEIVORIVII>...
- Page 18 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
Need help?
Do you have a question about the IP220 Series and is the answer not in the manual?
Questions and answers