Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Ayrton Diablo S
Summary of Contents for Ayrton Diablo S
- Page 1 Manuel d’utilisation KEEP THIS MANUAL FOR FUTURE NEEDS...
- Page 2 CONTENTS 1. SAFETY INSTRUCTIONS 2. FEATURES 3. FIXTURE OVERVIEW 4. DIMENSIONAL DRAWINGS 5. INSTALLATION INSTRUCTIONS 6. DMX-512 CONTROL CONNECTION 7. DMX-512 CONNECTION WITH DMX TERMINATOR 8. DEVICE DMX START ADDRESS SELECTION 9. DISPLAY 10. DMX PROTOCOL 11. ERROR MESSAGES 12. CLEANING AND MAINTENANCE...
- Page 3 1. SAFETY INSTRUCTIONS 1.1. IMPORTANT SAFETY WARNING This device has left the factory in perfect condition.In order to maintain this condition and to ensure safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. In order to install operate and maintain the lighting fixture safely and correctly we suggest that the installation and operation be carried out by qualified technicians and these instructions be carefully followed.
- Page 4 This device falls under protection-class I.Therefore it is essential that the device be earthed. If eitherlenses or displayare damaged (damage may include cracks or gashes in the material) they must be replaced. Electrical connections such as replacing the power plug must be performed by a qualified person.
- Page 5 AC100-240V~ 50/60Hz Power Consumption 550W LIGHT SOURCE LED White LED 330W 7000K±450K Color Temperature high CRI @ DIABLO TC White LED 330W 8000±500K Color Temperature @ DIABLO S Extremely long Life >20,000H MOVEMENT Pan movement 540º /630ºOptional (16 bit) Tilt movement 270º (16 bit)
- Page 6 Advanced and convenient full –color LCD with rechargeable battery(optional) Can be changed 180° reverse to fit for different installation position SOFTWARE 8 pre-installed programs available upon selection Upgrades fast and convenient through DMX cable with DMX-512 controller Reset DMX address remote lamp control reset can all be done by the DMX controller Running time of fixture on display for reference OTHER SPEC Input signal isolation guarantees stable signal transmission without interference...
- Page 7 3. FIXTURE OVERVIEW 1) LED Assembly 2) Display 3) Rotary knob 4) Handle 5) Lock button 6) DMX Out 7) DMX In 8) Power Out 9) Power In...
- Page 8 4. DIMENSIONAL DRAWINGS 4.1. Fixture Dimension...
- Page 9 4.2. Gobo Filter Dimension 4.3. Color Filter Dimension...
- Page 10 4.4. Animation Dimension...
- Page 11 5. INSTALLATION INSTRUCTIONS 8.1. Rigging the device CAUTION! PLEASE CONSIDER THE RESPECTIVE NATIONAL NORMS DURINGINSTALLATION. THE INSTALLATION MUST ONLY BE CARRIED OUT BY A QUALIFIED PERSON. The applicable temperature for the lighting is between -10°C to 45°C. Do not use the lighting under or above the temperature.
- Page 12 8.2. Rigging using the omega brackets Fix the clamp to the bracket by tightening the M12 nut and boltto the bracket through the 13 hole in the middle of the bracket. Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of the device.Tighten the quick-lock fasteners fully clockwise.
- Page 13 8.3. RIGGING DRAWINGS Be sure this fixture is kept at least 0.1m away from any flammable materials (decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails. Important Overhead rigging requires extensive experience including (but not limited to)
- Page 14 6. DMX-512 CONTROL CONNECTION Connect the provided male side of the XLR cable to the femaleXLR output of your controller and the female side of the XLR cable to the male XLR input of the device.You can connect multipledevices together in a serial fashion.The cable needed should be two core screened cable with XLR input and output connectors.Please refer to the diagram below.
- Page 15 8. DEVICE DMX START ADDRESS SELECTION All fixtures should be given a DMX starting address when using a DMX signal so that the correct fixture responds to the correct control signals.This digital starting address is the channel number from which the fixture starts to “ listen” to the digital control information sent out from the DMX controller.The allocation of this starting address is achieved by setting the correct address number on the display located on the base of the device.
- Page 16 CAUTION! THE BATTERY MUST BE A LI-ION RECHARGEABLE BATTERY, THE SPECIFICATION IS AS FOLLOWING: To install the battery for the first time please make sure the unit is not connected to AC power. Install the battery in the battery holder then remove the battery and install it back. This procedure must be done only for the first battery installation.
- Page 17 Signal Select WDMX WDMX Temp. C/F Celsius Temperature switch Fahrenheit between Initial Pos. PAN =XXX Initial effect position Wireless DMX Activate WDMX Activate WDMX Act&Data Out Act&Data Out Rest WDMX Rest WDMX Dim Curve Square Law Dim Curve Linear Refresh Select 1.2K Refresh Select 2.4K...
- Page 18 --Secne Time-- Input By Outside Scenes Input XX~XX Scenes Input 12.1.Address 9.1.1. Set DMX Address With this function you can adjust the desired DMX-address via the Display. 1. Double click to enter the menu. 2. The display will show“ADDRESS”. 3. Double click to enter then display“Set DMX Address”. 4.
- Page 19 Pan Reverse With this function you can reverse the Pan-movement. 1. Double click to enter the menu. 2. Turn the rotary knob clockwise then display“Options”. turn the rotary knob to select “Status”. 3. Double click to enter“Options 4. Double click to enter“Status”menu The display will show“Pan Reverse”. The display will show “OFF 5.
- Page 20 to select“OFF”. 6. Long press to exit the menu. Init TILT 1. Double click to enter the menu. 2. Turn the rotary knob clockwise then display“Options”. 3. Double click to enter“Options turn the rotary knob to select“Status”. 4. Double click to enter“Status”menu The display will show“Init TILT”. 5.
- Page 21 Clr LED Timer This function allows you to clear the led time 1 Double click to enter the menu. 2 Turn the rotary knob clockwise then display“Options”. 3 Double click to enter“Options turn the rotary knob to select“Service PIN”. 4 Double click to enter “ Clr LED Timer” menu The display will show “Clr LED Timer” . 5 Double click to enter “...
- Page 22 seconds.keeping press the <MODE/ESC>key for 3seconds if you do not need this function. 1 Double click to enter the menu. 2 Turn the rotary knob clockwise then display“Options”. turn the rotary knob to select “Display Setting”. 3 Double click to enter“Options 4 Double click to enter“Display Setting”menu The display will show“Key Lock”.
- Page 23 From factory this projector is prepared for wireless data transmission (W-DMX).If you wish to de-activate W-DMX control you can select the function “De-activate WDMX”by turning the encoder.With the function“rest you can log out the projector from the wireless sender. 1. Double click to enter the menu. 2.
- Page 24 1 Double click to enter the menu. 2 Turn the rotary knob clockwise then display“Options”. 3 Double click to enter“Options turn the rotary knob to select“Trigger”. 4 Double click to enter“Trigger”menu The display will show“Set To Slave”. 5 Double click to enter “Set To Slave The display will show “Slave1 “Slave2 “Slave3”.
- Page 25 2. Turn the rotary knob clockwise then display“Info”. 3. Double click to enter“Info turn the rotary knob to select“Time Info.”. The display will show “TtlLifeHrs”. 4. Double click to enter“Time Info. The display will show “XXXX (Hours)”. 5. Double click to enter“TtlLifeHrs 6.
- Page 26 9.4.2. Temp.Info HeadTemp. With this function you can display the temperature on the display board of the base (near CMY-filter) in Celsius. 1. Double click to enter the menu. 2. Turn the rotary knob clockwise then display“Info”. 3. Double click to enter“Info turn the rotary knob to select“Temp Info”.
- Page 27 9.5.3. Manual Control When set to Manual Mode fixture will be back to factory settings.If want to adjust brightness can adjust by shutter and dimming channel channel value is 0-255.Other functions can be set according to user's real need. 1 Double click to enter the menu. 2 Turn the rotary knob clockwise then display“Test”.
- Page 28 Note: Part 2 Part3 repeat in accordance with the Part1’s repeat.For example When Part 1 uses Program 2 Part 2 uses Program 4 Part 3 uses Program 6 Assume Program 2 includes scene of 10 11 12 13 Program4 includes scene of 8 9 10 Program 6 includes scene of12 13 14 15 Then it will run as below.
- Page 29 0-10 Shutter closed 11-20 No function (shutter open) 21-117 Strobe effect slow to fast 118-126 No function (shutter open) 127-180 Pulse-effect in sequences 181-191 No function (shutter open) 192-245 Random strobe effect slow to fast 246-255 No function (shutter open) Dimmer intensity: 0-255 Intensity 0 to 100%...
- Page 30 Color 1(CTB) 8-11 Color 2(Magenta) 12-15 Color 3(Congo Blue) 16-19 Color 4(Green) 20-23 Color 5(Orange) 24-27 Color 6(Light Blue) 28-31 Color 7(Red) 32-127 Color indexing 128-189 Forwards rainbow effect from fast to slow 190-193 No rotation 194-255 Backwards rainbow effect from slow to fast Color Wheel Fine : 0-255 Color Wheel colour change to any position Fine...
- Page 31 158-173 Gobo 6 shake slow to fast 174-189 Gobo 7 shake slow to fast 190-221 Gobo wheel rotation forwards from fast to slow 222-223 No rotation 224-255 Gobo wheel rotation f backwards from slow to fast Rotating gobo index,rotating gobo rotation 1: 0-127 Gobo indexing 128-189...
- Page 32 Blade 2 A : 0-255 Open to Close Blade 2 A Fine: 0-255 Open to Close Fine Blade 2 B: 0-255 Open to Close Blade 2 B Fine: 0-255 Open to Close Fine Blade 3 A: 0-255 Open to Close Blade 3 A Fine: 0-255 Open to Close Fine...
- Page 33 80-84 All motor reset 85-87 Scan motor reset 88-90 Colors motor reset 91-93 Gobo motor reset 94-96 Not used 97-99 Other motor reset 100-119 Internal program 1 (scene1~8 of EEPROM) 120-139 Internal program 2 (scene9~16 of EEPROM) 140-159 Internal program 3 (scene17~24 of EEPROM) 160-179 Internal program 4 (scene25~32 of EEPROM) 180-199...
- Page 34 14. ERROR MESSAGES When you turn on the device, it will first perform areset.The display may show“Err channel is XX”should there be problems with one or more functions.“XX” stands for channel 1 2 3 4 5 6 etc whose sensor has encountered a problem.For example when the display shows“Err channel is Pan movement it means there is an error on channel 1.If there are errors on channel 1 channel 3 channel 6 at the same time you may see the error message “Err channel is Pan...
- Page 35 Magenta Color wheel Er (Magenta Color wheel- error) This message will appear after the reset of the fixture if the head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective (or its driving IC on the main PCB).The CMY -movement is not located in the default position after the reset.
- Page 36 BLADE 1 wheel Er (BLADE 1 wheel - error) This message will appear after the reset of the fixture if the head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the steppermotor is defective (or its driving IC on the main PCB).The BLADE 1 - movement is not located in the default position after the reset.
- Page 37 (Animation_Rot wheel - error) This message will appear after the reset of the fixture if the head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the steppermotor is defective (or its driving IC on the main PCB).The Animation_Rot - movement is not located in the default position after the reset.