Page 2
Thank you for purchasing a Nivel System NL540 laser level. To best use the purchased instrument, please read the instructions carefully and put in a convenient spot so that in the future you will be able to use it.
Page 3
NL series levels may designate a vertical or horizontal laser plane, additionally the device defines the axis of the laser plane (laser line - point up and down). NL540 models can be controlled from the device control panel or remotely, with remote control.
Page 4
Never use a wet battery. The possibility of explosion. Never use a laser level near flammable gases and liquids. A short-circuit may cause a fire. Pay attention to not to short-circuit the battery while storing the device. Protection against shock When transporting the instrument it should be protected against shocks.
Once the green light shows the instrument is fully charged- charging normally takes 7 hours to give 50 hours of use. Use lasers NL540 with care, protect from moisture. Never put a wet instrument to the transport box (wait until dry).
Page 6
or work in difficult terrain, near the heavy construction equipment (does not react to the vibrations of the land). When the equipment is switched to manual mode, the display shows the "hand" icon. Select the inclination in axis (X, Y) - when the device is turned on - press the “G”...
10 cm). Working with the vertical plane NL540 can set horizontal or vertical beam. If you work with a vertical laser beam you must set the laser level on vertical position. After switching on the laser level the device will level by itself –...
Page 8
How to make connection between laser and remote controller: switch on the laser. By holding key for 3-5seconds until at screen of laser starts to flash switch on the remote, by holding key for for 3-5seconds until at screen of remote starts to flash ...
Page 9
Checking the vertical plane This procedure should be done after calibration of the horizontal plane. 1. Set the laser centered between the walls distanced from each other of 30 m 2. Turn on the laser level. 3. Place the paper sheets on the walls and mark the position of the laser beam. 4.
Page 10
LASER SENSOR RD700 DIGITAL display laser detector area level„zero” LED grade indicator lbubble keypad magnet unit (mm, cm, cal) On/Off / Beeper volume deadband resolution / LED On/Off Display numeric / text display grade indication arrows on grade indicator low battery grade indication arrows accuracy (1 / 2 / 5 / 10 mm) beeper volume...
Court with jurisdiction over the Warrantor’s registered office. 5. When the warranty services provided by the service centre are needed, please do not hesitate to contact your seller or a Nivel System service centre directly e-mail: service@nivelsystem.com...
Page 13
NL540 technical specification Laser red beam Light source laser diode, class II, 635 nm, output power <1mW ±1,0mm/10m Accuracy ±1mm/1,5m Accuracy of laser plummet ±5° Self-leveling range ±10% (digital) Inclination (X and Y axis) Work range (diameter) 500 m (with sensor)
Page 14
Dziękujemy za zakupienie niwelatora laserowego firmy Nivel System model NL540 Aby móc jak najlepiej wykorzystać zakupiony instrument, prosimy uważnie przeczytać instrukcję i położyć w dogodnym miejscu, żeby w przyszłości móc z niej skorzystać.
Page 15
WPROWADZENIE Wielozadaniowy niwelator laserowy to samopoziomujący laser budowlany, stosowany do wyznaczania różnicy wysokości przy pomiarach budowlanych. Model NL540 wykorzystuje wiązkę widzialnego światła i może być stosowany zarówno przy pracach wewnątrz budynku jak i na zewnątrz. Urządzenie zasilane jest z akumulatorków, które wykorzystują nowoczesną...
„własną rękę”. Istnieje ryzyko powstania pożaru, porażenia prądem lub obrażeń podczas samodzielnego wykonywania napraw. Naprawy mogą być wykonywane tylko przez serwis Nivel System lub jego autoryzowanych przedstawicieli. Wiązka lasera może być niebezpieczna dla wzroku człowieka przy nieprawidłowej obsłudze.
ładowania – dioda pali się na czerwono. Kiedy dioda zapali się na zielono, ładowanie zostaje zakończone. Jeżeli jest potrzeba wymiany akumulatorków - komora akumulatorków powinna być rozkręcona. Używaj niwelatorów NL540 z odpowiednią ostrożnością, chroń od zawilgocenia. Nigdy nie wkładaj mokrego instrumentu do kufra transportowego (zaczekaj aż obeschnie). PANEL STEROWANIA...
Page 18
Opis przycisków i funkcji: Włącznik/wyłącznik zasilania oraz przejście na tryb ręczny - włącza i wyłącza urządzenie - dłuższe przytrzymanie przycisku - ok. 6 sek. (gdy sprzęt jest włączony) włącza/wyłącza tryb ręczny. Sprzęt w trybie ręcznym może być pochylany (poza zakres samo-poziomowania) lub współpracować...
Praca z płaszczyzną pionową NL540 może wyznaczać wiązkę poziomą lub pionową. W przypadku pracy z wiązką pionową laser należy ustawić go w pozycji pionowej. Po włączeniu urządzenie samo spoziomuje się - głowica zacznie obracać się - wyznaczając płaszczyznę...
Page 20
Jak nawiązać połączenie między laserem a pilotem: włącz zasilanie lasera. Przytrzymaj przycisk przez 3-5 sekund aż symbol wyświetlaczu lasera zacznie migać włącz pilot, przytrzymaj przycisk przez 3-5 sekund aż symbol na wyświetlaczu pilota zacznie migać po tym laser i pilot połączą się automatycznie ...
Page 21
Uwaga! Jeśli błąd przekracza 3 mm, należy skontaktować się z serwisem. Sprawdzenie płaszczyzny pionowej Sprawdzenie to należy przeprowadzić po kalibracji płaszczyzny poziomej. 1. Ustaw instrument w połowie odległości między ścianami (odległymi o ok. 30 m od siebie). 2. Włącz niwelator. 3.
Page 22
CZUJNIK LASEROWY RD700 DIGITAL wyświetlacz detektor wiązki laserowej poziom „zero” sygnalizator LED libelka Moduł sterowania magnesy (mocowanie) zmiana jednostki pracy (mm, cm, cal) włącznie i wyłączanie zasilania / sygnalizatora dżwiękowego zmiana trybu pracy (dokładność) / włączenie/wyłączenie sygnalizatorów LED Wyświetlacz wskazania różnicy wysokości wskazania przewyższenia (powyżej „zera”) wskazania przewyższenia (poziom...
Gwaranta. W przypadku potrzeby skorzystania z usług serwisu gwarancyjnego prosimy o kontakt ze sprzedawcą lub bezpośrednio z serwisem Nivel System e-mail: service@nivelsystem.com ...
Page 25
Specyfikacja NL540 wiązka czerwona Laser Źródło światła 635 nm, <1mW Dokładność ±1,0mm/10m Dokładność pionownika ±1mm/1,5m 5 Zakres samo-poziomowania 10% (cyfrowo) Wyznaczanie spadków (oś X i Y) Zasięg pracy (średnica) 500 m (z czujnikiem) Prędkość wirowania głowicy zmienna: 0-120-300-600 obr/min Skanowanie 0-10°-45°-90°-180°...
Type of the instrument Rotating laser level Trade mark Nivel System Model NL540 Serial number The date of the check Instrument checked and calibrated Calibration technician EC declaration of conformity We declare that products Nivel System NL540 conform to: EN 61010-1:2010, EN 61326-1:2013...
Page 27
WARNING: The device contains a rechargeable Li-ion batteries which must be recycled and should be disposed in accordance with the requirements...