Page 1
Rotation Laser NL311, NL311G Thank you for purchasing a Nivel System NL311 / NL311G laser level. To best use the purchased instrument, please read the instructions carefully and put in a convenient spot so that in the future you will be able to use it.
Page 2
WARNING: The device contains a rechargeable nickel-hydrogen batteries which must be recycled and should be disposed in accordance with the requirements (WEEE-Reg .: DE23874031)
Page 3
(laser line - point up and down). The device can also "draw" a laser line (scan function) – thanks to it it's possible to stop the beam at a given distance. NL311 / NL311G models can be controlled from the device control panel or remotely, with remote control.
Page 4
A short-circuit may cause a fire. Pay attention to not to short-circuit the battery while storing the device. Protection against shock When transporting the instrument it should be protected against shocks. Strong shocks can cause measurements errors. The user of this instrument should follow the instructions contained in this manual and remember to periodically check the correctness of its working.
If it's necessary to replace the battery - battery compartment should be unscrewed with a screwdriver. Replacement batteries can be purchased from an authorized distributor. Use levelers NL311 / NL311G with care, protect from moisture. Never put a wet instrument to the transport box (wait until dry).
Page 6
(clockwise or counter-clockwise). The inclination of laser plane NL311/311G allows you to incline the laser plane in one or two directions Press 4 button which will go into a mode of enter the inclinations Press 3 to enable selection of the axis along which surface will be tilted (X or Y).
Working with the vertical plane NL311 / NL311G can set horizontal or vertical beam. If you work with a vertical laser beam you must set the laser level as in the picture beside. After switching on the laser level the device will level by itself –...
Page 8
Checking the laser level You should regularly check the following parameters of the laser level setting a horizontal plane cone error setting a vertical plane Checking and calibration of the horizontal and vertical planes is simple and in most cases can be done by the user.
7. Do not change the position of the laser and spin it 180°. 8. Mark the position of the laser beam on the paper sheet. Measure the distance between the markers 9. If the distance between the markers is less than 3mm calibration is not necesery. LASER SENSOR LCD Display Precise mode Coarse mode...
Court with jurisdiction over the Warrantor’s registered office. 5. When the warranty services provided by the service centre are needed, please do not hesitate to contact your seller or a Nivel System service centre directly (e-mail: serwis@tpi.com.pl, tel.: +48 22 632 91 40)
Page 12
NL311/NL311G technical specification Laser red beam (NL311), green beam (NL311G) Light source laser diode, class II 635 nm (NL301), 515 nm (NL301G), <1mW Accuracy ±1mm/10m Accuracy of laser plummet ±1mm/1,5m Self-leveling range ±5° Inclination (X and Y axis) ±8% (digital)
Page 13
Niwelator laserowy NL311, NL311G Dziękujemy za zakupienie niwelatora laserowego firmy Nivel System model NL311/NL311G Aby móc jak najlepiej wykorzystać zakupiony instrument, prosimy uważnie przeczytać instrukcję i położyć w dogodnym miejscu, żeby w przyszłości móc z niej skorzystać.
Page 14
UWAGA: Urządzenie zawiera baterie niklowo-wodorowe, baterie te muszą być poddane recyklingowi lub powinny być utylizowane zgodnie z wymogami (WEEE-Reg.: DE23874031)
Wielozadaniowe niwelatory laserowe to samopoziomujące lasery budowlane, stosowane do wyznaczania wysokości przy pomiarach budowlanych. Model NL311 / NL311G wykorzystuje wiązkę widzialnego światła (NL311 – czerwona wiązka, NL311G – zielona wiązka) i może być stosowany zarówno przy pracach wewnątrz budynku jak i na zewnątrz. Urządzenie zasilane jest akumulatorków,...
Page 16
Nigdy nie używaj rozładowanych baterii. Możliwość eksplozji. Nigdy nie używaj niwelatora w pobliżu łatwopalnych gazów i płynów. Zwarcie baterii może być przyczyną pożaru. Zwracaj uwagę, żeby podczas przechowywania nie doszło do zwarcia baterii Ochrona instrumentu przed wstrząsami Podczas transportu należy zabezpieczyć instrument przed wstrząsami (transportuj sprzęt w kufrze).
Jeżeli jest potrzeba wymiany akumulatorków - komora akumulatorków powinna być rozkręcona. Zastępcze akumulatorki można nabyć u autoryzowanego dystrybutora. Używaj niwelatorów NL311/NL311G z odpowiednią ostrożnością, chroń od zawilgocenia. Nigdy nie wkładaj mokrego instrumentu do kufra transportowego (zaczekaj aż obeschnie). PANEL STEROWANIA Opis przycisków i funkcji:...
Page 18
(zgodnie lub przeciwnie do ruchu wskazówek zegara). Pochylenie powierzchni laserowej NL311/311G umożliwia pochylanie powierzchni w jednym lub w obu kierunkach. Naciśnij przycisk 4 co spowoduje przejście urządzenia w tryb nadawania spadków. Naciśnij przycisk 3 co umożliwi wybór osi, wzdłuż której będzie pochylana powierzchnia (X, Y).
Po wprowadzeniu zadanego spadku dla osi X, osi Y, ponownie przyciśnij przycisk 3, po ok. 3 sekundach płaszczyzna zacznie być pochylana do zadanych wartości. Przyciśnięcie przycisku 4 spowoduje wyjście z trybu nadawania spadku, płaszczyzna zostanie automatycznie spoziomowana. ZASADA DZIAŁANIA Pomiar wysokości Włącz zasilanie, instrument sam spoziomuje się.
Page 20
SPRAWDZENIE Użytkownik powinien systematycznie sprawdzać następujące parametry pracy niwelatora ustawienie płaszczyzny poziomej błąd stożka ustawienie płaszczyzny pionowej Sprawdzenie i kalibracja płaszczyzny poziomej i pionowej jest proste i w większości przypadków może być wykonana przez użytkownika. Sprawdzenie błędu stożka może być wykonane przez użytkownika, ale błąd ten może zostać...
Page 21
6. Zaznacz na kartce miejsce położenia promienia lasera. Pomierz odległość między znacznikami. 7. Nie zmieniając pozycji lasera obróć go o 180. 8. Zaznacz na kartce miejsce położenia promienia lasera. Pomierz odległość między znacznikami. 9. Jeśli różnica odległości jest mniejsza niż 3 mm kalibracja nie jest konieczna. CZUJNIK LASEROWY Wyświetlacz LCD Tryb precyzyjny Tryb zgrubny...
W przypadku potrzeby skorzystania z usług serwisu gwarancyjnego prosimy o kontakt ze sprzedawcą lub bezpośrednio z serwisem Nivel System (e-mail: serwis@tpi.com.pl, tel.: +48 22 632 91 40) EC - DEKLARACJA ZGODNOŚCI Deklarujemy, że modele NL311, NL311G są zgodne z: EN 60825-1:2014, EN 5502:2010/AC:2011, EN 55024:2010...
Page 24
Specyfikacja NL311/NL311G Laser wiązka czerwona (NL311), wiązka zielona (NL311G) Źródło światła dioda laserowa, klasa II 635 nm (NL301), 515 nm (NL301G), <1mW Dokładność ±1mm/10m Dokładność pionownika ±1mm/1,5m 5 Zakres samo-poziomowania 8% (cyfrowo) Wyznaczanie spadków (oś X i Y) Zasięg pracy (średnica) 500 m (z czujnikiem) Prędkość...