1. Manuals
  2. Brands
  3. Huvema Manuals
  4. Drill
  5. HU 30 NC-4
  6. Manual

Huvema HU 30 NC-4 Manual

Column-drilling-machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
C O L U M N - D R I L L I N G - M A C H I N E
HU 30 NC-4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HU 30 NC-4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Huvema HU 30 NC-4

Summary of Contents for Huvema HU 30 NC-4

  • Page 1: Parts List Figure

    C O L U M N - D R I L L I N G - M A C H I N E HU 30 NC-4...

  • Page 2: Table Of Contents

    able des maTìeres General safety rules for all machines Additional safety rules Applications Main specifications Unpacking and checking contents Getting to know your drill press Assembly Lubrication Maintenance Wire diagram Troubleshooting Repair parts 10.1. Parts list figure 1 10.2. Parts list figure 2 10.3.

  • Page 3: General Safety Rules For All Machines

    HU 13 NC-4 eNeral safeTy rUles for all maCHiNes N.B.: Read the instructions carefully in order to avoid any problems. As with all machinery there are certain hazards involved with operation and use of this machine. Using the machine with respect and caution will considerably lessen the possibility op personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may occur.

  • Page 4: Additional Safety Rules

    ddiTioNal safeTy rUles Always keep in mind that: - the machine must be switched off and disconnected from the power supply during maintenance and repairs, - clamped workpieces may only be measured when the machine is switched off. Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap. Do not remove safety devices or guards.
  • Page 5 Description Description M12x1.75-40 long hex head scew Clamp-column lock M3 Hex “L” wrench Crank (With set screw) M4 Hex “L” wrench Handle Crank M5 Hex “L” wrench Feed handle M6 Hex “L” wrench Key-Chuck Key-drift Chuck Belt “V” A29 Idler pulley assembly Belt “V”...

  • Page 6: Getting To Know Your Drill Press

    2.Remove the protective oil that is applied to the table and column.Use any ordinary household type grease and spot remover. 3.Apply a coat of paste wax to the table and column to prevent rust.Wipe all parts thoroughly with clean dry cloth. If any parts are missing, please contact the seller.

  • Page 7: Assembly

    5. a ssembly Refer to the figure install all parts correctly, tighten the screw and bolts securelly. 1. Collar-Rack 2. Screw-Hex Soc Set M6*1.0-10 3. Support table w/indicator 4. Crank 5. Handle-crank 6. Rack 7 Screw-Hex Soc Set M10*1.5-12 8 support Column 9 Screw-Hex Hd M12*1.75-40 10 Base 11 Tube-Column...

  • Page 8: Troubleshooting

    Part no. Component/ Object Manufacturer Motor Motor AC400V/3PH/1500W Magnetic switch 400VAC/10A KJD18 Push Button-Emergency Stop 400VAC/12A HY57B Micro Switch 250VAC/16A KW-7-3B Micro Switch 250VAC/16A Transfer Switch 400VAC/10A ZH-A 9. T roUblesHooTiNG Trouble Probabale cause Remedy Noisy Operation 1.Incorrect belt tension. 1.Adjust tension.

  • Page 9: Repair Parts

    10. r epair parTs Figure 1 10.1. p arTs lisT fiGUre Key no. Description Key. no. Description Collar-Rack Tube Column Screw-Hex Soc set M6*1.0-10 Pin-Table Lock Support-Table w/Indicator Nut-Hex Hd M8*1.25 Crank Screw-Hex Hd M20*2.5-50 Handle-Crank Table w/Scale Rack Pin-Gear Screw-Hex Soc Set M10*1.5-12 Clamp-Column Support-Column...
  • Page 10 Figure 2 arTs lisT fiGUre Key no. Description Key. no. Description Nut-Lock M20*1.5 Key-Chuck Ring-Locking Chuck Washer Arbor Bearing-Ball 20mm Spindle Washer-Rubber Bearing-ball 30 mm Tube-Quill Bearing-Thrust Key-drill CHANGES AND T YPING ERRORS RESER VED...
  • Page 11 Figure 3 arTs lisT fiGUre Key no. Description Key. no. Description Belt-”V”A29 Washer Foam Bearing-Ball 15mm Guard-Pulley w/Labels Pully-Center Ring-Retaining Pivot-Ldler Bearing-Ball 30mm Pulley-Motor Spacer-Bearing Screw-Soc Set M8*1.25-12 Insert-Pulley Screw-Pan HD M5*0.8-12 Pulley-Spindle Clamp-Cord Nut-Pulley Bushing-Rubber Belt-”V”A33 Screw-RD Washer Hd M6*1.0-16 Knob Lock Washer Ext M6 CHANGES AND T YPING ERRORS RESER VED...
  • Page 12 Figure 4 arTs lisT fiGUre Key no. Description Key. no. Description Screw-Hex HD M8*1.25-16 Box Switch Lever-Adjusting Screw-Pan Cr M6*1.0-35 Support-Motor Bracket Switch Mount-Motor Screw-Self Tap Pan Hd M4.2*1.4-8 Lockwasher 12mm Key-Switch Nut-Hex M8*1.25 Cover-Switch Plate Motor Switch-Locker Nut-Hex M8*1.25 Screw-Pan Cr M6*1.0-15 Washer 8 Lead-3”...
  • Page 13 Knob Cord-Power Pin-Roll 2.5*10 Head w/Pointer and Trim Ring-Depth Stop W/Scale Connector-Wire Pin-Stop Screw-Pan Cr M6*1.0-12 Screw-Soc Hd Cap M8*1.25-30 Socket-Bulb Lock-Washer-Ext M5 Screw-Pan Cr M5*0.8-6 CHANGES AND T YPING ERRORS RESER VED...

  • Page 14: Ce Declaration Of Conformity

    (in accordance with supplement II A of the Machinery Directive) Industrie & Handelsonderneming Huberts bv, Kennedylaan 14, 5466 AA Veghel, the Netherlands, in the capacity of importer, is to be held responsible for declaring that the Huvema machine: HU 13 NC which this declaration relates to, is conform the following norms: •...
  • Page 15 CHANGES AND T YPING ERRORS RESER VED...
  • Page 16 Copyright © Huberts BV. All rights reserved.

Table of Contents