Huvema HU 40 GCC-4 TOPLINE Manual
  1. Manuals
  2. Brands
  3. Huvema Manuals
  4. Drill
  5. HU 40 GCC-4 TOPLINE
  6. Manual

Huvema HU 40 GCC-4 TOPLINE Manual

Industrial drilling machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
I N D U S T R I A L D R I L L I N G M A C H I N E
HU 40 GCC-4 TOPLINE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HU 40 GCC-4 TOPLINE and is the answer not in the manual?

Questions and answers

Related Manuals for Huvema HU 40 GCC-4 TOPLINE

Summary of Contents for Huvema HU 40 GCC-4 TOPLINE

  • Page 1 I N D U S T R I A L D R I L L I N G M A C H I N E HU 40 GCC-4 TOPLINE...

  • Page 2: Table Of Contents

    able of conTenTs General safety rules for all machines Additional safety rules Technical specifications Features Overall aspect Delivery & installation Unpacking Installation: Minimum room space for machine operation Use of main machine parts (see fig. L) Precaution for operation Adjusting table slack and compensate for wear (see fig. 3) 8 Clamping, table base, and machine base (see fig.

  • Page 3: General Safety Rules For All Machines

    hu 40 gcc-4 T ndusTrIal drIllIng machIne oplIne 1. g eneral safeTy rules for all machInes N.B.: Read the instructions carefully in order to avoid any problems. As with all machinery there are certain hazards involved with operation and use of this machine. Using the machine with respect and caution will considerably lessen the possibility op personal injury.

  • Page 4: Additional Safety Rules

    xTra veIlIgheIdsvo denk er steeds aan dat: 2. a ddITIonal safeTy rules - bij onderhouds- en rep Always keep in mind that: - ingespannen werkstukk • the machine must be switched off and disconnected from the power supply during maintenance and repairs, ga niet over de machine •...

  • Page 5: Overall Aspect

    Overall Aspect 4. o verall aspecT Arbor bolt cover Rapid speed for drilling Switch Speed lever Fine feed engagement Handle rod control Positive depth stop gauge Drill fine control Chuck guard calibrated Handle...

  • Page 6: Delivery & Installation

    5. d & elIvery InsTallaTIon 5.1 u npackIng Transportation to desired location before unpacking, please use lifting jack.(Fig. B) After unpacking, please use heavy duty fiber belt to lift up the machine. Allways keep proper footing & balance while moving this machine. Fig.B Installation: (1) BE SURE all locks of head-stock &...

  • Page 7: Use Of Main Machine Parts (See Fig. L)

    (1) To raise and lower the head by table. (2) Equipped with an electric switch for tapping operation clockwise or counterclockwise. (3) To adjust the quick or slow feeding by feed handle. 6. u . l) se of maIn machIne parTs (4) To adjust the table left and right travel by table handle wheel.

  • Page 8: Adjusting Table Slack And Compensate For Wear (See Fig. 3)

    Quill return spring adjustment: Spring tension for return of spindle, after hole drilling, has been pre-set at the factory. No further adjustment should be attempted unless absolutely necessary. Adjustment will probably be required if a multiple drilling or tapping head is used. If adjustment is necessary, loosen lock screw while holding. Do not allow the housing to turn in your hand, or spring will unwind.

  • Page 9: To Change Tools

    WARING: CHANGE SPEED ONLY WHEN MACHINE IS STOPPED For (4P) 50Hz 60Hz LEVERS 1260 1550 Table .1 10. T o change Tools (1) Removing Face Mill or Drill Chuck Arbor 10. TO CHANGE TOOLS Loosen the arbor bolt (see fig. 4) at the top of the spindle shaft approximately 2 turns with a wrench. (1) Removing Face Mill or Drill Chuck Arbor Rap the top of the arbor bolt with a mallet.

  • Page 10: Specification Of T-Solt

    EDING chine and push out the handle rod D, then the spindle will feed down automatically d of stroke you set. EMERGENCY switch F to stop the spindle running. Use button C for instant reverse of the UTO FEEDING spindle. will return to top when reaching the end of stroke you set.

  • Page 11: Lubrication

    16.2 l ubrIcaTIon All ball bearings in your mill/drill are sealed for life, requiring no lubrication. Points requiring lubrication are: (1) Internal spline drive assembly. Keep this area well lubricated with a good grade non-hardening grease, such as Fiske Company “Lubriplate”. Insert grease in the hole at the top of spindle pulley spline driver.
  • Page 12 Shake of spindle (a) The gap of spindle bearing too wide - Adjust the gap in proper or replace bearing and roughness with new one. of working (b) Spindle loosening up and down - Make two of inner bearing covers on the top surface has taken tight each other.

  • Page 13: Circuit Diagram

    19. c IrcuIT dIagram...

  • Page 14: Power Down Feed Operation

    needed. When adjusting the feeding depth, first release the dial fix-nut “B”(see Fig.2)and turn the indicating ring “c” to the depth needed. Then reset “B” “tightly again. 20. p ower down feed operaTIon 4. Start the machine and push out the handle rod “F”(see Fig.2), then the spindle 1.

  • Page 16: Exploded Drawings

    21. e xploded drawIngs -22-...
  • Page 17 -23-...
  • Page 18 -24-...

  • Page 19: Parts List

    22. p arTs lIsT PARTS LIST MODEL NO. 40HC / 40HS CODE NO PART NO DESCRIPTION SPECIFICATION NOTE 2401011S Head Body Set 2401001-2 Main Shaft Cover 6101 MT3 M10xP1.5 Chuck Arbor Bolt 6101-1 MT3 M12xP1.75 Chuck Arbor Bolt 6101-2 MT3 W3/8"-16 Chuck Arbor Bolt 6101-3 MT3 W1/2"-12...
  • Page 20 PARTS LIST MODEL NO. 40HC / 40HS CODE NO PART NO DESCRIPTION SPECIFICATION NOTE 11-7 6119-1 NT30 Bearing Cap 6554S Graduated Rod Set 6193 S008 1/4"x2"L Hex. Head Screw N003 1/4" Hex. Nut 6192 Position Set Bracket 61105S Spring Base Set S732 3/16"x3/4"L Cross Round Head Screw...
  • Page 21 PARTS LIST MODEL NO. 40HC / 40HS CODE NO PART NO DESCRIPTION SPECIFICATION NOTE HH001 Rivet ∮2 S708 Cross Round Head Screw 3/16"-24UNCx3/8"L 2401195 Lock Bolt 5/8"-11UNCx5-1/2"L W019 Washer 5/8" N008 5/8"-11UNC Hex. Nut 2401106 Pinion Shaft S307 3/16"x1/2"L Flat Cross Head Screw HK042 7x7x20L 61108S...
  • Page 22 PARTS LIST MODEL NO. 40HC / 40HS CODE NO PART NO DESCRIPTION SPECIFICATION NOTE 6120-4 25.4 W7/16"-20 Cutter Arbor 6120-7 27 M12xP1.75 Cutter Arbor 6120-9 Cutter Arbor 6120-10 27 M10xP1.5 Cutter Arbor 6122D MT3 M12-∮22 Cutter Arbor 6122 NT30 Cutter Arbor 6121 MT3 M10xP1.5 Chuck Arbor...
  • Page 23 PARTS LIST MODEL NO. 40HC / 40HS CODE NO PART NO DESCRIPTION SPECIFICATION NOTE 2401020S Gear Shaft HB001 ∮5/16"，∮0.8x7L Steel Ball/Spring 2401029S Gear Set 2401192A Bushing 2401031B Gear Shaft HK014 5x5x50L HK036 6x6x75L HCS07 C-Retaniner Ring 2401055 Gear 2401037S Gear Set HG004 ∮35x∮62x8t Oil Seal...
  • Page 24 -30-...
  • Page 25 -31-...
  • Page 26 -32-...
  • Page 27 -33-...
  • Page 28 PARTS LIST MODEL NO. 40C2F / 40S2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE 2450002S Head Body Set 2401001-2 Main Shaft Cover 6101 MT3 M10xP1.5 Chuck Arbor Bolt 6101-1 MT3 M12xP1.75 Chuck Arbor Bolt 6101-2 MT3 W3/8"-16 Chuck Arbor Bolt 6101-3 MT3 W1/2"-12 Chuck Arbor Bolt...
  • Page 29 PARTS LIST MODEL NO. 40C2F / 40S2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE W007 3/16" Washer For CE Only S708 3/16"x3/8"L Cross Round Head Screw For CE Only HS504 M3x15L Cross Round Head Screw For CE Only E075732 Control Wire For CE Only 61105S...
  • Page 30 PARTS LIST MODEL NO. 40C2F / 40S2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE 6120-3 25.4 W1/2"-12 Cutter Arbor 6120-4 25.4 W7/16"-20+D182 Cutter Arbor 6120-7 27 M12xP1.75 Cutter Arbor 6120-9 Cutter Arbor 6120-10 27 M10xP1.5 Cutter Arbor 6122D MT3 M12-∮22 Cutter Arbor 6122 NT30...
  • Page 31 PARTS LIST MODEL NO. 40C2F / 40S2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE CA6202ZZ 6202ZZ Bearing 2450005 Gear HS421 M6x6L Hex. Socker Headless Screw HCS06 C-Retainer ring HG002 ∮17x∮35x8t Oil Seal CA6003ZZ 6003ZZ Bearing HK007 5x5x16L HK006 5x5x10L 2450004 Transmission Worm 2450053...
  • Page 32 PARTS LIST MODEL NO. 40C2F / 40S2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE 401-8 HS421 M6x6L Hex. Socker Headless Screw 401-9 2450074A Bushing 401-10 2450072A Gear 401-11 2450071A Gear 401-12 2450070A Gear 401-13 2450073A Worm Shaft 401-14 HK010 5x5x28L 401-15 2450008...
  • Page 33 PARTS LIST MODEL NO. 40C2F / 40S2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE 416-3 2450030 Bushing Pin 416-4 2450032A Inch Scale Base 416-4 2450032B Metric Scale Base 416-5 HP017 ∮5 416-6 2450037 Handle Body 416-7 2450039 Handle Rod Pin 416-8 2450033 Scale Base Set Screw...
  • Page 34 -40-...
  • Page 35 PARTS LIST MODEL NO. 40HC / 40C2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE 12228 Table 6229 Fixed Block 6230 Movable Fixed Ring S402 1/4"x1/2"L Hex. Socket Head Screw HB111 1/4" Oil Ball 6601BS Table Handle Wheel 6027-1S Clamp Handle 6620 ∮17 Table Clutch...
  • Page 36 PARTS LIST MODEL NO. 40HC / 40C2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE 6605AS Metric Table Base Screw 6605BS Inch Table Base Screw 6611 Column Head S610 5/16"x5/16"L Hex. Socker Headless Screw 62217A Collar S627 1/2"x5/8"L Hex. Socker Headless Screw 62241-1 Base 62216...
  • Page 37 PARTS LIST MODEL NO. 40HC / 40C2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE 6158 Head Handle S630 3/8"x1/2"L Hex. Socker Headless Screw W205 Spring Washer 5/16" HD103 Plug PT1/4"x3/8"L 6630 Brass Bush 6241A Vise -43-...
  • Page 38 -44-...
  • Page 39 PARTS LIST MODEL NO. 40HS / 40S2F CODE NO PART NO DESCRIPTION SPECIFICATION QTY NOTE 623306 Swivel Base 62268 Bushing Bracket 62202S Bearing Cover (Lower) Set HB003 3/8" Steel Ball HP022 ∮5x38L 62213 Bearing Cover N007 5/16" Hex. Nut 62214 Fiexed Screw 62216 Column Base...

Table of Contents