Download Print this page
Eaton McGraw-Edison GLNA Galleonaire LED Installation Instructions Manual

Eaton McGraw-Edison GLNA Galleonaire LED Installation Instructions Manual

Advertisement

Available languages

Available languages

Quick Links

IB500021EN
Installation Instructions – Galleon / Galleonaire
Directives d'installation – Galleon / Galleonaire
Instrucciones de instalación – Galleon / Galleonaire
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this
product must be performed by a qualified electrician. This product must be installed in accordance
with the applicable installation code by a person familiar with the construction and operation of the
product and hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting
any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Fire- Refer to product label for specific minimum supply conductor requirements.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Fixture may become damaged and/or unstable if not installed properly.
Failure to comply with these instructions may result in death, serious bodily injury and property damage.
N
otee:
These instructions do not claim to cover all details or variations in the equipment, procedure, or process
described, nor to provide directions for meeting every possible contingency during installation, operation
or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for
user's purpose, please contact your nearest representative.
N
otee:
Care must be taken not to set lighting fixture down on optical lenses or lift the fixture in the lens area.
N
otee:
Specifications and dimensions subject to change without notice.
DISCLAIMER OF LIABILITYe: Eaton assumes no liability for damages or losses of any kind that may arise from the
improper, careless, or negligent installation, handling or use of this product.
NOTICEe: Green ground wire provided in proper location. Do not relocate.
ATTENTION Receiving Departmente: Note actual fixture description of any shortage or noticeable damage on
delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be
filed within 15 days of delivery. All damaged material, complete with original packing must be retained.
Safety: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and
ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under
installation section.
APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area
of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to
installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation
and insertion of photo control or shorting cap (if so equipped). Best results will be obtained if installed and
maintained according to the following recommendations.
WARNING
Brand Logo
reversed out of
black
INS #
INS #

Advertisement

loading
Need help?

Need help?

Do you have a question about the McGraw-Edison GLNA Galleonaire LED and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Eaton McGraw-Edison GLNA Galleonaire LED

  • Page 1 Specifications and dimensions subject to change without notice. DISCLAIMER OF LIABILITYe: Eaton assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product. NOTICEe: Green ground wire provided in proper location. Do not relocate.
  • Page 2: Installation Instructions

    40 ft-lbs./54 N·m. Set the fixture assembly 12. Close the cover and tighten the three screws to insure aside. the fixture will maintain it’s water tight seal. 13. Replace pole top cap after completion of fixture installation and wiring. EATON IB500021EN Installation instructions...
  • Page 3 Loosen (3) screws located in the access door of the fixture and open the door. Pull all supply wires through the mast arm/mast arm adapter and into the center grommet located between the mounting bolts at the back of the fixture. EATON IB500021EN Installation instructions...
  • Page 4: Maintenance

    A regular maintenance schedule should be followed to retain optimal light output and thermal performance. Optical lens cleaning should be performed with a clean dry cloth to remove any dust or other contaminants. Additional cleaning can be performed with non-abrasive acrylic cleansing solution. EATON IB500021EN Installation instructions...
  • Page 5 Les caractéristiques techniques et les dimensions sont sujettes à modifications sans préavis. EXONÉRATION DE RESPONSABILITÉ e: Eaton n’assume aucune responsabilité pour les dommages ou pertes de quelque nature que ce soit pouvant découler d’une installation, d’une manipulation ou d’une utilisation inappropriée, imprudente ou négligente de ce produit.
  • Page 6 Serrez les écrous au dos de la plaque murale 14. Replacez la protection supérieure du poteau une fois décorative selon un couple de 651 N·m. Mettez le l’installation et le câblage du luminaire terminés. luminaire de côté. EATON IB500021EN Instructions d’installation...
  • Page 7 Tournevis à tête cruciforme nº 2, perceuse et foret de 1,11 À Enfiler Sur La Crosse cm, cliquet et douille de 1,42 cm. Figure 3. Installation Avec Adaptateur Pour Crosse (Figure 3.) Desserrez les (3) vis de la porte d’accès du luminaire et ouvrez la porte. EATON IB500021EN Instructions d’installation...
  • Page 8 Le nettoyage de la lentille optique doit être fait à l’aide d’un linge propre et sec afin de retirer toute la poussière et les autres contaminants. Il est possible de nettoyer l’appareil plus en profondeur à l’aide d’une solution de nettoyage acrylique non abrasive. EATON IB500021EN Instructions d’installation...
  • Page 9 Las especificaciones y las dimensiones están sujetas a cambios sin previo aviso. RENUNCIA DE RESPONSABILIDADe: Eaton no asume ninguna responsabilidad por daños o pérdidas de ningún tipo que puedan derivarse de la instalación, manipulación o uso incorrecto, descuidado o negligente de este producto.
  • Page 10: Instrucciones De Instalación

    (cables completo. El lado largo debe estar en la parte superior blancos). del accesorio. 13. Cierre la cubierta y ajuste los tres tornillos para asegurarse de que el accesorio mantendrá ajustado su sellado de agua. EATON IB500021EN Instrucciones de instalación...
  • Page 11 Cierre la cubierta y ajuste los tres tornillos para asegurarse de que el accesorio mantendrá ajustado su sellado de agua. Placa De Sujeción (Hardware Para Otros) Junta De Pared Detalle De Montaje De Hardware (Arandelas/arandelas De Presión Y Tuercas) Figura 2. EATON IB500021EN Instrucciones de instalación...
  • Page 12: Mantenimiento

    óptimos. Debe limpiar la lente óptica con un paño seco árboles, etc. pueden afectar la posición final del limpio para extraer el polvo o cualquier otro contaminante. fotocontrol. Puede realizar limpieza adicional con una solución de limpieza de acrílico no abrasiva. EATON IB500021EN Instrucciones de instalación...
  • Page 13 Warranties and Limitation of Liability Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions. Garanties et limitation de responsabilité Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones.

This manual is also suitable for:

Galleon