Viking pump 323A Series Technical & Service Manual page 12

DANGER !
• Always disconnect, lockout, and tag out
supply circuits prior to installing.
• The installation must comply with standard
and local regulations.
• All wiring should be done by a licensed
electrician to meet local codes.
• Study this manual thoroughly before
installing and using the heat cartridges.
• Pay special attention to this section and the
parts marked "WARNING!" or "DANGER".
• Should questions or uncertainties arise,
please contact your authorized Viking
distributor.
Failure to follow these instructions may cause
an electrical shock and/or sparks, which may
result in serious injury or death.
NOTE:
1.
Heat cartridges, temperature probes, and controllers
must be wired by a licensed electrician to meet local
codes.
2. Heat cartridges require 240VAC, 1 Phase, 60 Hz or
220VAC, 1 Phase, 50 Hz power supply.
3. Heat cartridges are UL, CSA, & CE marked, RoHs
compliant.
4. Heat cartridges and cables are water resistant but not
water proof. They need to be installed in a protected
area.
5.
To make sure that the liquid within the pump is melted
and to avoid damage to the pump, do not start the pump
until the set point temperature has been reached.
6. Several factors such as the size of pump, the set point
temperature, and the insulation will affect the amount
of time it will take for the pump to reach the set point
temperature. Typically it will take 3-4 hours for the pump
to reach its set point temperature.
7. Do not use heat cartridges with different watt densities
from those supplied by Viking. Changing watt densities
may result in localized over or under heating.
8.
The thermocouple or temperature probe must be
installed in the bracket location shown in Figure 13
below. Any other location may result in localized over or
under heating.
9. Please see TSM 630.4 for technical information on the
Viking supplied controller for the heat cartridges.
VIKING PUMP, INC.
TECHNICAL SERVICE MANUAL
UNIVERSAL SEAL HEAVY DUTY PUMPS
SERIES 324A/AH/E/EH & 4324A/AH CAST IRON
SERIES 327A & 4327A STAINLESS STEEL
•
A Unit of IDEX Corporation
SERIES 323A & 4323A STEEL
SIZES N, R AND RS
WARRANTY
Viking pumps, strainers and reducers are warranted to be
free of defects in material and workmanship under normal
conditions of use and service. The warranty period varies by
type of product. A Viking product that fails during its warranty
period under normal conditions of use and service due to a
defect in material or workmanship will be repaired or replaced
by Viking. At Viking's sole option, Viking may refund (in cash
or by credit) the purchase price paid to it for a Viking product
(less a reasonable allowance for the period of use) in lieu of
repair or replacement of such Viking product. Viking's warranty
is subject to certain restrictions, limitations, exclusions and
exceptions. A complete copy of Viking's warranty, including
warranty periods and applicable restrictions, limitations,
exclusions and exceptions, is posted on Viking's website
(www.vikingpump.com/warranty/warranty-info). A complete
copy of the warranty may also be obtained by contacting
Viking through regular mail at Viking Pump, Inc., 406 State
Street, Cedar Falls, Iowa 50613, USA.
THIS WARRANTY IS AND SHALL BE VIKING'S SOLE
AND EXCLUSIVE WARRANTY AND IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ALL WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGMENT, ALL OF WHICH
OTHER WARRANTIES ARE EXPRESSLY EXCLUDED.
THE RIGHTS AND REMEDIES UNDER THIS WARRANTY
ARE AND SHALL BE THE SOLE AND EXCLUSIVE RIGHTS
AND REMEDIES AGAINST VIKING. EXCEPT FOR THE
SPECIFIC LIABILITIES AND OBLIGATIONS PROVIDED
UNDER THIS WARRANTY, VIKING SHALL HAVE NO
LIABILITY OR OBLIGATION WITH RESPECT TO ANY
PRODUCT CLAIMED TO BE DEFECTIVE IN ANY MANNER.
UNDER NO CIRCUMSTANCES
LIABLE UNDER THIS WARRANTY OR OTHERWISE FOR
SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENTIAL OR
PUNITIVE DAMAGES OF ANY KIND, INCLUDING, BUT NOT
LIMITED TO, LOST OR UNREALIZED SALES, REVENUES,
PROFITS, INCOME, COST SAVINGS OR BUSINESS, LOST
OR UNREALIZED CONTRACTS, LOSS OF GOODWILL,
DAMAGE TO REPUTATION, LOSS OF PROPERTY, LOSS
OF INFORMATION OR DATA, LOSS OF PRODUCTION,
DOWNTIME, OR INCREASED COSTS, IN CONNECTION
WITH ANY PRODUCT, EVEN IF VIKING HAS BEEN ADVISED
OR PLACED ON NOTICE OF THE POSSIBILITY OF SUCH
DAMAGES AND NOTWITHSTANDING THE FAILURE OF
ANY ESSENTIAL PURPOSE OF ANY PRODUCT.
10. The wires for the heat cartridges can be joined together
in a junction box, and a single wire from the junction box
can be connected to the controller.
11. WARNING Heat cartridges will be hot. Do not touch
pump or heat cartridges until they have been allowed
to cool.
•
Cedar Falls, IA 50613 USA
SECTION TSM 630.3
PAGE 12 OF 12
ISSUE L
SHALL VIKING BE
© 6/2018 Viking Pump Inc.
All rights reserved