Viking pump KE4195 Service Manual

Viking pump KE4195 Service Manual

Heavy-duty pumps 4195 series sizes ke, kke, lqe, lse, q, & qs
Hide thumbs Also See for KE4195:

Advertisement

Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com
CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Information. . . . . . . . . . . . . . . . . . . . 2
Special Information . . . . . . . . . . . . . . . . . . . 3
Special Mechanical Seals. . . . . . . . . . . . . . . . 3
Maintenance . . . . . . . . . . . . . . . . . . . . . . 3
Disassembly . . . . . . . . . . . . . . . . . . . . . . 4
Assembly . . . . . . . . . . . . . . . . . . . . . . . . 7
Thrust Bearing Adjustment . . . . . . . . . . . . . . . 8
Pressure Relief Valve Instructions . . . . . . . . . . . 9

INTRODUCTION

The illustrations used in this manual are for identification
purposes only and cannot be used for ordering parts. Obtain a
parts list from the factory or a Viking® representative. Always
give complete name of part, part number and material with
model number and serial number of pump when ordering
repair parts. The unmounted pump or pump unit model
number and serial number are on the nameplate.
In the Viking model number system, basic size letters are
combined with series number (4195) are used to indicate
either an unmounted pump or mounted pump unit.
KE- K KE
KE, KKE, LQE, & LSE 4195 SERIES - Flange & Foot Mounted Unmounted Pumps with Flanged Ports
Q & QS 4195 SERIES - Foot Mounted Unmounted Pumps with Flanged Ports
VIKING PUMP, INC.
TECHNICAL SERVICE MANUAL
SIZES KE, KKE, LQE, LSE, Q, & QS
L QE -LS E
FIGURE 1
A Unit of IDEX Corporation
HEAVY-DUTY PUMPS
SERIES 4195
UNMOUNTED PUMP
Flange & Foot Mounted
KE4195
LQE4195
KKE4195
LSE4195
Foot Mounted
Q4195
QS4195
This manual deals only with Series 4195 Heavy Duty Pumps.
Refer to Figures 1 through 10 for general configuration and
nomenclature used in this manual. Pump specifications and
recommendations are listed in Catalog Section 144, Series
4195 and 495 Heavy Duty Pumps.
Cedar Falls, IA 50613 USA
SECTION
TSM 144.1
PAGE
1 OF 10
ISSUE
B
UNITS
Units are designated by the
unmounted pump model
numbers followed by a
letter(s) indicating drive style.
D = Direct Drive
M = Horizontal Direct Drive
R = Reducer Drive
D = Direct Drive
R = Reducer Drive
Q -Q S

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KE4195 and is the answer not in the manual?

Questions and answers

Summary of Contents for Viking pump KE4195

  • Page 1: Table Of Contents

    Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL SECTION TSM 144.1 HEAVY-DUTY PUMPS PAGE 1 OF 10 SERIES 4195 ISSUE SIZES KE, KKE, LQE, LSE, Q, & QS...
  • Page 2: Safety Information

    For weight of the pump alone (which does not include ● You know what material the pump has been the drive and/or base plate) refer to the Viking Pump handling, have obtained a material safety data product catalog.
  • Page 3: Special Information

    For additional information on pressure relief valves, refer to Technical Service Manual TSM 000 and Engineering Service Bulletin ESB-31. DANGER ! SPECIAL MECHANICAL SEALS: Before opening any Viking pump liquid chamber This bulletin illustrates the mechanical seal which is standard (pumping chamber, reservoir,...
  • Page 4: Disassembly

    All 4195 models referenced in this TSM are disassembled and assembled in the same manner. DANGER ! Mark the head and casing before disassembly to insure proper reassembly. Before opening any Viking pump liquid chamber (pumping chamber, reservoir, relief valve Remove the head capscrews.
  • Page 5 FIGURE 4 - EXPLODED VIEW FOR MODELS KE, KKE, LQE, LSE 4195 ITEM NAME OF PART ITEM NAME OF PART ITEM NAME OF PART Locknut Ball Bearing (Inner) Head and Idler Pin Assembly Lockwasher Casing Capscrews for Head End Cap for Bearing Housing Head O-Ring Relief Valve O-Rings Bearing Spacer Collar...
  • Page 6 BEARING SPACER COLLAR INNER BALL BEARING OUTER BALL BEARING SETSCREW BEARING SPACER COLLAR LOCKNUT SHAFT ENDCAP BEARING HOUSING SETSCREW BEARING SPACER FIGURE 6 - THRUST BEARING ASSEMBLY KE, KKE, LQE, LSE SIZES INNER BALL BEARING OUTER BALL BEARING SETSCREW BEARING SPACER COLLAR LOCKNUT SHAFT ENDCAP...
  • Page 7: Assembly

    ASSEMBLY TAPERED INSTALLATION SLEEVE Standard Mechanical Seal (Synthetic Rubber Bellows Type) READ CAREFULLY BEFORE REASSEMBLING PUMP The seal used in this pump is simple to install and good performance will result if care is taken during installation. SHAFT The principle of a mechanical seal is contact between the FIGURE 8 rotary and stationary members.
  • Page 8: Thrust Bearing Adjustment

    .005” LQE, LSE 5/8” .005” DANGER ! Q, QS 11/16” .010” Before opening any Viking pump liquid chamber TABLE 1 (pumping chamber, reservoir, relief valve adjusting cap fitting, etc.) Be sure: 1. That any pressure in the chamber has been...
  • Page 9: Pressure Relief Valve Instructions

    PRESSURE ADJUSTMENT Mark the valve and head before disassembly to ensure proper reassembly. If a new spring is installed or if the pressure setting of the Remove the valve cap. pressure relief valve is to be changed from that which the factory has set, the following instructions must be carefully Measure and record the length of extension of the followed.
  • Page 10 FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ALL OF WHICH OTHER WARRANTIES ARE EXPRESSLY EXCLUDED. See complete warranty at www.vikingpump.com. • • © 6/2016 Viking Pump Inc. VIKING PUMP, INC. A Unit of IDEX Corporation Cedar Falls, IA 50613 USA All rights reserved...

This manual is also suitable for:

Lse4195Kke4195Lqe4195Qs4195Q4195

Table of Contents