Pyrolytic Cleaning Of The Oven Cavity; Pyrolytic Cleaning Operation; Before Carrying Out The Pyrolytic Function; After Pyrolytic Cleaning - Westinghouse WVE613 User Manual

3. Repeat step 2 until display shows 24:68. 3 beeps
sound and DEMO will be shown.
4. To disable DEMO mode repeat steps 1-3.

Pyrolytic cleaning of the oven cavity

The oven has the Pyrolytic self-cleaning function. It
cleans by burning off the spatters and accumulated dirt
and grease from the oven liner, at high temperature. This
process produces ash which can then be wiped out of the
oven cavity.
Pyrolytic cleaning will not remove salt and mineral
residue left in the cavity well when water evaporates.
It is recommended that the residue is cleaned prior
to conducting pyrolytic cleaning cycles. See section
'Cleaning the cavity well'.
WARNING
During the pyrolytic cleaning process the oven becomes
extremely hot.
• Please keep small children at a safe distance.
• Never clean non-stick baking trays and tins in the
oven during the pyrolytic cycle. High temperatures
damage the non-stick coating and poisonous gas
is released.
• To prevent damage, do not use acids, sprays or
similar cleaning agents.
CAUTION
• During pyrolytic cleaning the air outlet exhaust
above the door must be kept clear of any
obstruction (e.g. bulky tea towels).
• Do not use the oven to clean miscellaneous items
(e.g. cookware).

Before carrying out the Pyrolytic function

1. All accessories must be removed from the oven,
including shelves, trays and side racks.
2. Clean large deposits, spills or grease from the
oven cavity.
3. Ensure the cavity well is free of limestone scaling
(refer to cleaning the cavity well chapter)
4. Choose the Pyrolytic cleaning cycle from
the following:
soiling
light clean
normal clean
NOTE: Duration includes heat-up time, excluding
cool-down time.
Light clean
This is an energy saving cycle that can be used on a
regular basis if the oven is lightly soiled. Possibly after
every 2nd or 3rd roast.
duration
1hr 30mins
2hr 30mins
Normal clean
Use this as the regular cycle about once every
2-3 months.

Pyrolytic Cleaning Operation

The pyrolytic cleaning function can be selected by turning
the function selector switch clockwise to the pyrolytic
position. Use or to toggle between a pyrolytic
cleaning time of 1:30 hours or 2:30 hours. The pyrolytic
function can be stopped at any time by turning the
function selector counterclockwise to the OFF position.
IMPORTANT
During Pyrolytic cleaning the door will automatically
lock when the temperature in the oven approaches
300˚C. will appear on the display. During the
pyrolytic cleaning cycle there may be some burn off
odours. It is advised to keep the room well ventilated
during this cycle.
When the pyrolytic cleaning function is on, it is advisable
not to use a cooktop if it is fitted above the oven. This
could cause overheating and damage to both appliances.
The door will only unlock when the oven has cooled to a
safe temperature. Turning the function off will not unlock
the door. This will only happen when safe temperature
is reached.
NOTE: The cooling fan will operate at an increased speed
for Pyrolytic cleaning and will continue to run until the
oven has cooled down. This is normal. It is recommended
to clean the oven regularly to keep it in its best condition.

After Pyrolytic cleaning

After cool-down, wipe the ash out of the oven with a soft
damp cloth and warm water.
To restore the enamel shine to more difficult areas, use a
damp cloth with vinegar and detergent.
CAUTION
Do not turn off the mains power supply to the
oven during the pyrolytic cycle. This could
damage the appliance.
This knob cannot be
turned anticlockwise
from off position
25
USING YOUR OVEN