Removing The Crisper And Crisper Cover; Ice Cube Trays - Whirlpool ET14JK Use And Care Manual

Pull Shelf Out Until It Stops.
Lift the Front and Pull Agarn
Lift the Front, Then the Back -
Pull out to stop. -
Lift the Front and Pull Again.
A Twist of the Wrists
Raise Signal
Arm to Stop Ice Maker
Lower Signal
Arm to Start It
Adjusting the Shelves.
Adjust your refrigerator shelves to match your food storage
needs
for tall items, short items or sizes in between. It will be easier to move
a shelf if you take off all the food first.
Slide the shelf you want to move toward you until it stops. Lift up the
front and slide it out the rest of the way. To put it back on the shelf
guides, fit the back of the shelf on top of the guides with the wire
stops on the bottom of the guides. Slide it in, keeping the front
litted
up until the stops on the shelves clear the stops on the guides.
Removing the Crisper and Crisper Cover.
To remove the crisper, slide it out until it stops. Lift the front a little
and slide it out the rest of the way.
The cover rests on nubs built into the side walls of the refrigerator.
To remove the cover, lift the front and then the back. To replace the
cover, fit the notches in the back corners of the cover over the nubs
at the back of the walls. Then lower the front into place.
To replace the crrsper, slide It in, keeping the front lifted a little until
the crisper clears the stops
Replacing the Light Bulb.
WARNING: Before removing the light bulb, either unplug the re-
frigerator or disconnect the electricity leading to the refrigerator at
the main power supply. Shock and injury can occur if electricity
remains connected. To replace bulb, reach behind the control
con-
sole to find the bulb. Remove bulb and replace it with
a
40-watt ap-
pliance bulb.
Ice Cube Trays.
To remove ice from the flexible ice trays, hold a tray at both ends,
as shown. Slightly twist the tray; the ice will come out easily.
If cubes are not used for a number of weeks, they may become
smaller. The moving air is so cold that it starts a slow evaporation.
[That's also why it's so important to wrap food carefully.) The longer
they are stored, the smaller they can get.
Optional ICE MAGIC" Automatic Ice Maker.
If you have the automatic ice maker accessory or plan to add
one later [Part No. ECKMF-83) there are a few things you will want to
know.
l
The ON I OFF lever IS a wtre signal arm.
Down...for making Ice automatically;
Up .to shut off the Ice maker
l
Shake the brn occaslonally to keep cubes separated, and to obtain
Increased storage capacity.
l
It IS normal for Ice crescents to be attached by a corner. They will break
apart easily
l
You wtll hear water running when Ice maker is working. You'll hear ice
fall Into the bin. Don't let these sounds bother you.
l
The Ice maker will not operate until the freezer is cold enough
to make
Ice. This can take overnight
. Because of new plumbing connecttons, the first Ice may be discolored
or off-flavored. Discard the ftrst few batches of ice.
l
If ice is not being made fast enough and mcxe ice is needed, turn the
Refrigerator Control toward a higher number. Wait a day and, if nec-
essary, turn the Freezer Control toward A
l
If you remove the ice bin, raise the signal arm to shut off the Ice maker.
When you return the bin, push it all the way in and lower the arm to the
ON position
l
If cubes are stored too long, they may develop an off-flavor.like stale
water Throw them away. They will be replaced, Cubes in the ice bin
can also become smaller by evaporation.
l
The ICE: maker water supply
should not be softened water.
The chem-
icals could damage the Ice maker rnolds
5