Table of Contents
Advertisement
Quick Links
KNX LW sl
Brightness and Wind Sensor
Technical specifications and installation instructions
Item number 70164
EN
Elsner Elektronik GmbH Control and Automation Engineering
Sohlengrund 16
D - 75395 Ostelsheim Phone +49 (0) 70 33 / 30 945-0 info@elsner-elektronik.de
Germany
Fax
+49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for elsner elektronik KNX LW sl
Summary of Contents for elsner elektronik KNX LW sl
- Page 1 KNX LW sl Brightness and Wind Sensor Technical specifications and installation instructions Item number 70164 Elsner Elektronik GmbH Control and Automation Engineering Sohlengrund 16 D - 75395 Ostelsheim Phone +49 (0) 70 33 / 30 945-0 info@elsner-elektronik.de Germany +49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de...
-
Page 2: Technical Specification
Dimensions approx. 62 × 71 × 145 (W × H × D, mm) Weight approx. 85 g Ambient temperature Operation -30…+50°C, storage -30…+70°C Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes. -
Page 3: Installation Notes
• EN 60730-1: 2011 Installation and start-up 2.1. Installation notes Installation, testing, operational start-up and troubleshooting should only be performed by an electrician. Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes. -
Page 4: Installation Location
There must be at least 60 cm clearance to oth- er elements (structures, construction parts, etc.) below, to the sides and in front of the de- vice. 60 cm Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes. - Page 5 The device must be mounted in the horizontal Horizontal (transverse) direction. Fig. 4 The device must be aligned in the direction of the façade which is to be shaded. Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes.
-
Page 6: Device Design
Even a few drops of water can damage the device electronics. • Do not open the device if water (e.g. rain) can get into it. Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes. - Page 7 Fig. 8 The device is installed with two screws. Break off the two longitudinal holes in the lower part of the housing. Longitudinal holes Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes.
- Page 8 ATTENTION! The printout of the data sheet does not have original size! A separate, di- mensionally correct drilling plan is included ex works and this can be used as a tem- plate. Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes.
- Page 9 Feed the power lead through the rubber gas- ket. Rubber gasket Cable guide 2.4.3. Connection The connector is in the lower part of the housing. Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes.
-
Page 10: Instructions For Assembly And Initial Start-Up
The wind measurement value and thus also all wind switching outputs cannot be out- put until 35 seconds after the power is turned on. Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes. -
Page 11: Addressing The Equipment
15 mm. Use a thin object to reach the key, e. g. a 1.5 mm² wire. Fig. 17 Programming button for teaching the device Programming LED (under the semi-transparent lid) Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes. -
Page 12: Maintenance
ATTENTION The device can be damaged if water penetrates the housing. • Do not clean with high pressure cleaners or steam jets. Brightness and Wind Sensor KNX LW sl • Status: 05.11.2014 • Errors excepted. Subject to technical changes.
Need help?
Do you have a question about the KNX LW sl and is the answer not in the manual?
Questions and answers