elsner elektronik KNX R Installation And Adjustment
  1. Manuals
  2. Brands
  3. elsner elektronik Manuals
  4. Accessories
  5. KNX R
  6. Installation and adjustment

elsner elektronik KNX R Installation And Adjustment

Rain sensor
Hide thumbs Also See for KNX R:
Table of Contents

Advertisement

Quick Links

Download this manual
EN
KNX R
Rain Sensor
Installation and Adjustment

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KNX R and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for elsner elektronik KNX R

Summary of Contents for elsner elektronik KNX R

  • Page 1 KNX R Rain Sensor Installation and Adjustment...

  • Page 2: Table Of Contents

    6.2.4. Linkage inputs of OR logic ................. 18 Elsner Elektronik GmbH • Herdweg 7 • D-75391 Gechingen • Germany Rain Sensor KNX R • from software version 1.00, ETS programme version 1.1 Status: 20.08.2013 • Errors excepted. Subject to technical changes.
  • Page 3 Clarification of signs Installation, inspection, commissioning and troubleshooting of the device must only be carried out by a competent electrician. This manual is amended periodically and will be brought into line with new software releases. The change status (software version and date) can be found in the contents footer. If you have a device with a later software version, please check www.elsner-elektronik.de in the menu area "Service"...

  • Page 4: Description

    Description Description The Rain Sensor KNX R registers precipitation and transfers the status to the KNX system. One switching output as well as AND and OR logic gates are available. The sensor system, the evaluation electronics and the electronics of the bus connection are mounted in a compact housing.

  • Page 5: Installation And Commissioning

    Elsner Elektronik is not liable for any changes in norms and standards which may occur after publication of these operating instructions.

  • Page 6: Mounting The Sensor

    Fasten the mount vertically onto the wall or pole. Fig. 3 When wall mounting: flat side on wall, crescent- Collar shaped collar upward. Rain Sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.
  • Page 7 Sun, wind and precipitation can act upon the sensors without hindrance. Fig. 7 Example use of the hinge arm mounting: Fitting to a pole with worm drive hose clips Rain Sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 8: View Of Rear Side And Drill Hole Plan

    2.3.2. View of rear side and drill hole plan Fig. 8 a+b Drill hole plan Dimensions of rear side of housing with bracket. Sub- ject to change for technical enhancement. Langloch 7,5 x 5 mm Rain Sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 9: Preparing The Sensor

    For 24V devices the connection cable must be plugged in between the cover and circuit board. Rain Sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 10: Pcb Layout

    1.5 mm² or conductors with fine wires 4) Slot for KNX clamp +/- Opening for the bus cable 6) Programming pushbutton for the teach-in of the device 7) Programming LED Rain Sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 11: Mounting The Sensor

    “click”. Fig. 13 Make sure the cover and bottom part are properly snapped together! This picture is looking at the closed sensor from under- neath. Fastening Rain Sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 12: Notes On Mounting And Commissioning

    The device is supplied with the bus address 15.15.250. You can program another ad- dress into the ETS by overwriting the 15.15.250 address or by teaching via the pro- gramming key on the circuit board inside the housing. Rain Sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 13: Maintenance

    ATTENTION The device can be damaged if significant volumes of water penetrate the housing. • Do not clean with high pressure cleaners or steam jets. Rain Sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 14: Transmission Protocol

    OR Logic 4 Switching Output C R T OR Logic 4 8 bit Output A C R T OR Logic 4 8 bit Output B C R T Rain sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.
  • Page 15 C R W Logic Input 6 Input C R W Logic Input 7 Input C R W Logic Input 8 Input C R W Software Version readable Rain sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 16: Setting Of Parameters

    5 sec … 2 h (only if sending “cyclically”) Maximum telegram quota 1 • 2 • 3 • 5 • 10 • 20 Telegrams per second Rain sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 17: Logic

    Logic 1 / 2 / 3 / 4 not active • active Transmission delay of switching outputs 5 secs … 2 h after power up and programming Rain sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.
  • Page 18 • in case of the change of logic to 1 and cyclically • in case of the change of logic to 0 and cyclically send cyclically every 5 sec … 2 h (only if sending “cyclically”) Rain sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.

  • Page 19: Linkage Inputs Of And Logic

    AND logic output 2 AND logic output 2 inverted AND logic output 3 AND logic output 3 inverted AND logic output 4 AND logic output 4 inverted Rain sensor KNX R • Status: 20.08.2013 • Technical changes reserved. Errors reserved.
  • Page 20 Elsner Elektronik GmbH Control and Automation Technology Herdweg 7 D – 75391 Gechingen Phone +49 (0) 70 56 / 93 97-0 info@elsner-elektronik.de Germany +49 (0) 70 56 / 93 97-20 www.elsner-elektronik.de...

Table of Contents