Table of Contents
Advertisement
The following warnings and operating instructions are intended to
avoid unsafe operating practices which might lead to injury or
property damage.
Ingersoll-Rand recognizes that most companies who use material
handling equipment have a safety program in force at their facility.
If you are aware that some conflict exists between a rule set forth
in this publication and a similar rule already set by an individual
company, the more stringent of the two should take precedence.
The manual supports a fully installed system. Operators should be
familiar with the operation of the controls before using the system.
Safe Operating Instructions are provided to make an operator
aware of dangerous practices to avoid and are not necessarily
limited to the following list. Refer to specific sections in the
manual for additional safety information.
1.
Only allow personnel trained in, safety and operation on this
product to operate and maintain the balancer.
2.
Only operate a balancer if you are physically fit to do so.
3.
When a "DO NOT OPERATE" sign is placed on the
balancer controls, do not operate unit until sign has been
removed by designated personnel.
Manipulator arms consist of a connecting linkage type boom that
folds within itself to offer a large coverage area, these arms utilize
the Balance Air® lifting and balancing unit as the lifting power.
Series 700C Arm - Column/Ceiling Mounted
Arm Length
Part No.
ft
70015A**Z0613
6
70015A**Z0713
7
70015A**Z0813
8
70015A**Z0913
9
70015A**Z1013
10
70020A**Z0613
6
70020A**Z0713
7
70020A**Z0813
8
70020A**Z0913
9
70020A**Z1013
10
70035A**Z0613
6
70035A**Z0713
7
70035A**Z0813
8
70050A**Z0613
6
**
When ordering, please specify mounting option desired:
T00 = Ceiling mount
B00 = Column mount
4
SAFE OPERATING INSTRUCTIONS
SPECIFICATIONS
Capacity
Weight
m
lbs
kg
lbs
1.83
xx
2.13
xx
2.44
150
65
xx
2.74
xx
3.05
xx
1.83
xx
2.13
xx
2.44
200
90
xx
2.74
xx
3.05
xx
1.83
xx
2.13
350
155
xx
2.44
xx
1.83
500
225
xx
REVIEW COPY 9-7-99
4.
Do not use unit if hook latch has been sprung or broken.
5.
Before each shift, check unit for wear and damage. Never use
a unit that inspection indicates is worn or damaged.
6.
Never lift a load greater than rated capacity of unit. Refer to
capacity labels attached to the unit.
7.
Only operate the unit when the wire rope is centered over the
load. Do not "side pull" or "yard".
8.
Never operate unit with twisted, kinked or damaged wire
rope.
9.
Never run wire rope over a sharp edge.
10. Pay attention to the load at all times when operating the unit.
11. Make sure everyone is clear of the load path. Do not lift a
load over people.
12. Never use the unit for lifting or lowering people, and never
allow anyone to stand on a suspended load.
13. Never weld or cut a load suspended by the unit.
14. Do not operate the unit if wire rope is jumping, or if
excessive noise, jamming, overloading, or binding occurs.
15. Shut off air supply before performing any maintenance.
16. Avoid collision or bumping of the units.
17. Do not turn continuously in one direction when using the
arm.
18. Do use good posture when operating the system.
19. Do check air connections for leakage.
Series 700C Arm - Carriage Mounted
Part No.
kg
xx
70015A**Z0600
xx
70015A**Z0700
xx
70015A**Z0800
xx
70015A**Z0900
xx
70015A**Z1000
xx
70020A**Z0600
xx
70020A**Z0700
xx
70020A**Z0800
xx
70020A**Z0900
xx
70020A**Z1000
xx
70035A**Z0600
xx
70035A**Z0700
xx
70035A**Z0800
xx
70050A**Z0600
**
When ordering, please specify mounting option desired:
CA1 = Carriage A1 (A1 available only in 6, 7, 8 ft
[1.83, 2.13, 2.44 m] lengths / 150 and 200 lbs
[65 and 90 kg] capacity)
CA2 = Carriage A2
CS3 = Carriage S3
CE8 = Carriage ETA8
CS2 = Carriage S2
CTR = Carriage T-Rail
Arm Length
Capacity
ft
m
lbs
kg
6
1.83
7
2.13
8
2.44
150
65
9
2.74
10
3.05
6
1.83
7
2.13
8
2.44
200
90
9
2.74
10
3.05
6
1.83
7
2.13
350
155
8
2.44
6
1.83
500
225
MHD56162 - Edition 1
Weight
lbs
kg
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
Advertisement
Table of Contents
