Related Manuals for ESAB Miggytrac B501
Summary of Contents for ESAB Miggytrac B501
- Page 1 Miggytrac™ B501 Instruction manual 0463 404 001 GB 20150116 Valid for: serial no. 1501 xxxx...
-
Page 3: Table Of Contents
Weld operation ....................11 Start and stop of tractor ..................11 MAINTENANCE ....................12 Daily........................12 ORDERING SPARE PARTS ................13 DIMENSION DRAWING.....................14 ORDERING NUMBERS .....................15 ACCESSORIES ......................16 Rights reserved to alter specifications without notice. 0463 404 001 © ESAB AB 2015... -
Page 4: Safety
1 SAFETY SAFETY Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace. - Page 5 As the person responsible for the equipment, it is your responsibility to obtain information on approved collection stations. For further information contact the nearest ESAB dealer. 0463 404 001 - 5 - © ESAB AB 2015...
-
Page 6: Introduction
45°. A battery and a battery charger are not included in the delivery, refer to the "ACCESSORIES" chapter in this manual. ESAB's accessories for the product can be found in the "ACCESSORIES" chapter of this manual. 0463 404 001 - 6 - ©... -
Page 7: Technical Data
Horizontal tensile force without magnet 12 kg Horizontal tensile force with magnet 25 kg Vertical tensile force at 45° with magnet 11 kg Dimensions (l×w×h) 310 × 290 × 250 mm 0463 404 001 - 7 - © ESAB AB 2015... -
Page 8: Installation
Control panel Battery Driving wheels Adjust the front arm Adjust the front arm to be 10 mm shorter than the rear arm so that the Miggytrac™ goes diagonally along the plate. 0463 404 001 - 8 - © ESAB AB 2015... -
Page 9: Install The Battery
4 INSTALLATION Install the battery The Miggytrac™ is designed for a 18 volt battery with a capacity of 4 Ah. NOTE! Charge the battery with an approved battery charger before use. 0463 404 001 - 9 - © ESAB AB 2015... -
Page 10: Install The Magnet Kit (Optional)
A magnet kit can be installed at the bottom of the tractor to further stabilize the movement and increase the friction between the drive wheels and the foundation. CAUTION! The maximum slope of the foundation is set to 45° for security reasons. 0463 404 001 - 10 - © ESAB AB 2015... -
Page 11: Operation
Red blinking light Red rapidly blinking light NOTE! Charge the battery after a working day. NOTE! Make sure to have at least two charged batteries as back-up if welding in two shifts. 0463 404 001 - 11 - © ESAB AB 2015... -
Page 12: Maintenance
Daily • Charge the battery after each working day. • Clean the guide wheels, the drive wheels and the bottom of the Miggytrac™ with compressed air. 0463 404 001 - 12 - © ESAB AB 2015... -
Page 13: Ordering Spare Parts
Spare parts may be ordered through your nearest ESAB dealer, see the last page of this document. -
Page 14: Dimension Drawing
DIMENSION DRAWING DIMENSION DRAWING 0463 404 001 - 14 - © ESAB AB 2015... -
Page 15: Ordering Numbers
ORDERING NUMBERS ORDERING NUMBERS Ordering number Denomination Type Notes 0457 357 882 Miggytrac™ B501 Battery excluded 0463 404 001 - 15 - © ESAB AB 2015... -
Page 16: Accessories
0457 468 070 Battery, Makita 18V 4 Ah 0457 468 072 Battery charger, Makita 0457 468 073 Battery (18 V) and battery charger kit, Makita 0457 357 131 Magnet kit 0463 404 001 - 16 - © ESAB AB 2015... - Page 17 ACCESSORIES 0463 404 001 - 17 - © ESAB AB 2015...
- Page 18 ESAB subsidiaries and representative offices Europe NORWAY North and South America SOUTH KOREA AS ESAB ESAB SeAH Corporation AUSTRIA Larvik ARGENTINA Kyungnam ESAB Ges.m.b.H Tel: +47 33 12 10 00 CONARCO Tel: +82 55 269 8170 Vienna-Liesing Fax: +47 33 11 52 03...