Subscribe to Our Youtube Channel
Related Manuals for ESAB Arc 151i
Summary of Contents for ESAB Arc 151i
- Page 1 ® Caddy Arc 151i, Arc 201i Instruction manual 0460 446 101 GB 20110628 Valid for serial no. 927-xxx-xxxx...
- Page 2 - 2 -...
-
Page 3: Table Of Contents
1 SAFETY ............2 INTRODUCTION . -
Page 4: Safety
SAFETY Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of welding equipment. -
Page 5: Introduction
ESAB can provide you with all necessary welding protection and accessories. INTRODUCTION Arc 151i, Arc 201iis a welding current power source intended for use with coated electrodes (MMA welding) and TIG welding. ESAB's accessories for the product can be found on page 19. -
Page 6: Equipment
Equipment Arc 151i, Arc 201i is supplied with a 3 m welding cable, return cable, 3 m mains cable and an instruction manual for power source and control panel. Instruction manuals in other languages can be downloaded from the website, www.esab.com. -
Page 7: Technical Data
Equipment marked IP23 is designed for indoor and outdoor use. Application class The symbol indicates that the power source is designed for use in areas with increased electrical hazard. - 7 - © ESAB AB 2008 bh32d1e... -
Page 8: Installation
16 A 13 A type C MCB 16 A NOTE! The cable area and fuse rating above comply with Swedish regulations. Use the welding power source in accordance with the relevant national regulations. - 8 - © ESAB AB 2008 bh32d1e... -
Page 9: Operation
PFC circuit making it possible to use the full range of the machine on a 16 A fuse. The PFC also protects the machines against fluctuating mains voltage and makes it safer to use with a generator. Caddyt Arc 151i/201i can operate with extra long mains cables, over 100 m, giving you a very larger working radius. -
Page 10: Connection Of Welding And Return Cable
MMA welding Arc 151i / 201i gives direct current, and you can weld most metals to alloy and non- alloy steel, stainless steel and cast iron. Arc 151i / 201i allows you to weld most coated electrodes from Ø 1.6 to Ø 3.25. -
Page 11: Tig Welding
TIG welding is particularly useful where high quality is demanded and for welding thin plate. Arc 151i / 201i also has good characteristics for TIG welding. In order to TIG weld Arc 151i / 201i must be equipped with:... -
Page 12: Inspection And Cleaning
Check that the correct electrodes are being used. Check the gas flow. Fault codes Arc 151i, 201i comes with built-in fault monitoring. If a fault occurs, a code is shown in the display. See instruction manual for the control panel. - 12 - ©... -
Page 13: Ordering Spare Parts
Repair and electrical work should be performed by an authorized ESAB serviceman. Use only ESAB original spare and wear parts. Arc 151i, Arc 201i is designed and tested in accordance with the international and Eu ropean standards EN 60974-1 and IEC 60974-10 . It is the obligation of the service unit which has carried out the service or repair work to make sure that the product still conforms to the said standard. -
Page 14: Diagram
Diagram Arc 151i - 14 - © ESAB AB 2008 bh32e... - Page 15 - 15 - © ESAB AB 2008 bh32e...
- Page 16 Arc 201i - 16 - © ESAB AB 2008 bh32e...
- Page 17 - 17 - © ESAB AB 2008 bh32e...
-
Page 18: Ordering Number
Arc 151i, Arc 152i, A31 â 0459 839 028 Spare parts list Caddy Arc 151i, Arc 201i, A33 Instruction manuals and the spare parts list are available on the Internet at www.esab.com - 18 - © ESAB AB 2008 bh32o... -
Page 19: Accessories
Welding cable kit, Arc 151i ....0700 006 898 Return cable kit, Arc 151i ....0700 006 899 Welding cable kit, Arc 201i . - Page 20 Arc 151i/Arc 201i Only for A33 control panel Remote control MMA 1 (10 m cable) ..0349 501 024 MMA and TIG: current Foot control FS002 ..... .
- Page 21 NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ - 21 -...
- Page 22 ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ - 22 -...
- Page 23 - 23 -...
- Page 24 ESAB Romania Trading SRL ESAB VAMBERK s.r.o. SOUTH AFRICA ESAB Mexico S.A. Bucharest Vamberk ESAB Africa Welding & Cutting Ltd Monterrey Tel: +40 316 900 600 Tel: +420 2 819 40 885 Durbanvill 7570 - Cape Town Tel: +52 8 350 5959...
Need help?
Do you have a question about the Arc 151i and is the answer not in the manual?
Questions and answers