Table of Contents
Advertisement
Quick Links
OPERATING MANUAL
for
MORSO manual notching machine
Model NFL
Hoffmann Machine Company, Inc.
1386 Drexel Road
Valdese, NC 28690 USA
Fax: (828) 430 – 4620
Phone: (828) 430 - 4510
e-mail: info@Hoffmann-USA.com
www.Hoffmann-USA.com
Toll-free Technical Support: (866) 248 – 0100
© Hoffmann Machine Company, Inc.
Advertisement
Table of Contents
Related Manuals for Hoffmann MORSO
Summary of Contents for Hoffmann MORSO
- Page 1 OPERATING MANUAL MORSO manual notching machine Model NFL Hoffmann Machine Company, Inc. 1386 Drexel Road Valdese, NC 28690 USA Fax: (828) 430 – 4620 Phone: (828) 430 - 4510 e-mail: info@Hoffmann-USA.com www.Hoffmann-USA.com Toll-free Technical Support: (866) 248 – 0100 © Hoffmann Machine Company, Inc.
-
Page 2: Table Of Contents
Instructions Manual MORSØ Notch Cutting Machine Model NF CONTENTS Introduction page A-1 Work Piece Shortening of the work piece on a circular saw before cutting page B-1 Functional Description general description page C-1 machine description page C-2 description of the lever system page C-3 Technical Data... -
Page 3: Introduction
Instructions Manual MORSØ Notch Cutting Machine Model NF INTRODUCTION We recommend to read this instruction manual carefully before the first starting of the machine. Defects on the machine provably arisen due to mistakes in operation will not be covered by the warranty. -
Page 4: Work Piece
Instructions Manual MORSØ Notch Cutting Machine Model NF WORK PIECE Shortening of work piece on a circular saw before cutting Before the cutting of the work piece it must be shortened in the correct length on a circular saw. It is very important that the saw blade is exactly adjusted in 90°... -
Page 5: Functional Description
Instructions Manual MORSØ Notch Cutting Machine Model NF FUNCTIONAL DESCRIPTION C-1 General Description MORSØ-NF notch cutting machine is an important help to cut window bars, mullions, and cabinet front frames requiring haunch joints. MORSØ-NF is a manual foot-operated machine. The operation is easy. MORSØ-NF notch cutting machine is provided with 6 sliding longitudinal stops, fences (1500 mm) on both the right and left side of the machine,... -
Page 6: Machine Description
Instructions Manual MORSØ Notch Cutting Machine Model NF FUNCTIONAL DESCRIPTION C-2 Machine Description The MORSØ-NF is constructed as a compact machine with a solid dimensioned frame (1), with built in lever system (2). The cutting function (3) is placed on top of the machine. -
Page 7: Description Of The Lever System
Instructions Manual MORSØ Notch Cutting Machine Model NF FUNCTIONAL DESCRIPTION C-3 Description of the Lever System The cutting movement is carried out manually. The length of stroke of the knives is adjusted to max. 165 mm. The cutting takes place by means of a foot operated lever system. -
Page 8: Technical Data
Instructions Manual MORSØ Notch Cutting Machine Model NF TECHNICAL DATA Machine Dimensions (max.): Length (a) 3700 mm Width (b) 510 mm Height (c) 1150 mm Weight 96 kg Placing Measures: Spaciousness to Wall min. 1000 mm Noise/Pollution: Noise Level noiseless Pollution none/no dust Working Capacity:... -
Page 9: Mounting Instructions
Instructions Manual MORSØ Notch Cutting Machine Model NF MOUNTING INSTRUCTIONS E-1 In General The machine is delivered ready for start and complete with standard equipment. Only the table extensions (1) and fences (2) are dismounted during transport. NOTE before starting up first time: 1. -
Page 10: Operating Instructions
Instructions Manual MORSØ Notch Cutting Machine Model NF OPERATING INSTRUCTIONS F-1 Before Starting Before starting the machine the following must be checked and adjusted: Check a) knives (1) general condition sharpness b) waste room for waste c) safety devices fitting of all safety devices: safety guard for knives (2) d) table and table extension cleanness and undamaged surface... -
Page 11: Adjustment Of Cock-Bead Stops
Instructions Manual MORSØ Notch Cutting Machine Model NF OPERATING INSTRUCTIONS F-2 Adjustment of the cock-bead stops The cock-bead stops (1) are adjusted as follows: 1. Loosen the Allen screws on the cock-bead stops (1) and move these to rear of the sliding guide. -
Page 12: Adjustment Of Centre Stop
Instructions Manual MORSØ Notch Cutting Machine Model NF OPERATING INSTRUCTIONS F-3 Adjustment of the centre stop The centre stop regulates the amount of material cut from the corners of the cross-rails. The centre stop is adjusted as follows: 1. The adjustment screws (1) are located in each side of the Teflon head (3) on the centre stop (2). -
Page 13: Adjustment Of Flip Stops
Instructions Manual MORSØ Notch Cutting Machine Model NF OPERATING INSTRUCTIONS F-4 Adjustment of the flip-stops Making a Template For setting the flip stop positions a template of the stile (upright section) is made. Mark the centre of the positions on the cross-rails, incl. the top and bottom rails (see fig. -
Page 14: Adjustment Of Height Stop
Instructions Manual MORSØ Notch Cutting Machine Model NF OPERATING INSTRUCTIONS F-5 Adjustment of Height Stop The height stop (1) is used for adjustment of the knife block (2) to a suitable height compared to the moulding to be cut. In this way you avoid unnecessary high foot movements. -
Page 15: Cutting Of Bars With Rebate
Instructions Manual MORSØ Notch Cutting Machine Model NF CUTTING OF BARS G-1 Cutting of bars with rebate With the MORSØ-NF machine it is also possible to cut bars with rebate. You must make support mouldings (1) and support blocks (3) for the rebate in the bar. If these devises are not used the rebate will splinter during cutting. -
Page 16: Lubrication Instructions
Instructions Manual MORSØ Notch Cutting Machine Model NF SERVICE Lubrication Instructions Approx. every two weeks lubricate: The guidings for 1. Knife block (1) 2. Slide Frame (2) 3. Cross (3) (lubricates simultaneously the forward movement of the knife block). 4. Links for the draw bar (4) of the knife block. 5. -
Page 17: Changing Of Knives And Chip Breakers - Adjustment
Instructions Manual MORSØ Notch Cutting Machine Model NF SERVICE Changing of Knives and Chip Breaker – Adjustment 1. Knife Block (1) is placed in top position 2. The side knives (2) + (3) are dismounted by loosening screws (6). The nose knife (4) is dismounted by loosening screws (5). -
Page 18: Grinding Of Knives
Instructions Manual MORSØ Notch Cutting Machine Model NF SERVICE Grinding of Knives When grinding the knives you must only grind on the reverse of the cutting edge. You must under no circumstances grind on the front or ends of the knives, because the knives will then be destroyed. -
Page 19: Regulation Of Draw Bar
Instructions Manual MORSØ Notch Cutting Machine Model NF SERVICE Regulation of Draw Bar As the knives are worn it will be necessary to adjust the draw bar (1). The following procedure is used: 1. The foot pedal (2) is pressed home and locked by means of the height stop (3). -
Page 20: Adjustment Of Springs
Instructions Manual MORSØ Notch Cutting Machine Model NF SERVICE Adjustment of Springs The springs (1) that move the knife block (2) to the top position are by means of the spring holders (3) fastened in the bottom holes in the sides of the frame. -
Page 21: Changing Of Spare Parts
Instructions Manual MORSØ Notch Cutting Machine Model NF SERVICE Changing of Spare Parts If it is necessary to change worn out or destroyed parts we recommend that you proceed in the following way: 1. In the index of the spare parts list (see page K- 1) it is shown in which specified list the spare part can be found. - Page 22 Instructions Manual MORSØ Notch Cutting Machine Model NF LOCATING FAULTS Faults Cause Repair Incorrect cuttings Dull knives Replace knives See page H-2 Knives incorrectly installed Check the installation See page H-2 Incorrect measures The flip stops incorrectly Correct the adjustment adjusted See page F-4 Wrong dimension of end piece...
-
Page 23: Safety
Instructions Manual MORSØ Notch Cutting Machine Model NF SAFETY Safety Devices According to current safety regulations MORSØ- NF must not be used without the following safety devices: 2. Safety Guard (1) for knife block Safety Regulations On delivery of the machine to the consumer guarantees that the MORSØ-NF notch cutting machine is constructed and fitted according the CEN/TC 142 (Safety Regulations for wood...