Subscribe to Our Youtube Channel
Related Manuals for Vantron VT-IoT-Dongle
Summary of Contents for Vantron VT-IoT-Dongle
- Page 1 VT-IOT-Dongle VT‐IoT‐Dongle User’s Manual Chengdu Vantron Technology, Ltd. www.vantrontech.com.cn 1/ 21...
- Page 2 VT-IOT-Dongle Revision History: No. Version Description Date 1 V1.0 First release 2018.06.25 2 V1.1 Second release 2018.09.27 3 V1.2 Third release 2018.10.16 4 V1.3 Fourth release 2018.12.25 2/ 21...
-
Page 3: Table Of Contents
VT-IOT-Dongle Table of Contents 1. Foreword .......................... 4 1.1 Copyright Notice ........................4 1.2 Notes ............................4 1.3 Statement ...........................4 1.4 Disclaimer ...........................4 1.5 Limitation of Liability/Non‐warranty ..................5 1.6 Safety Instructions ........................5 1.7 Precautions ..........................5 1.8 Safety Instructions for Power Cables and Accessories ...............5 2. Overview .......................... 7 ... -
Page 4: Foreword
Please contact our technical department for relevant operation solutions if there is any problem that cannot be solved according to this manual. Vantron reserves all rights of this manual, including the right to change the content, form, product features, and specifications contained herein at any time without prior notice. The latest version of this manual is at ... -
Page 5: Limitation Of Liability/Non-Warranty
VT-IOT-Dongle 1.5 Limitation of Liability/Non‐warranty For direct or indirect damage to this device or other devices of Vantron caused by failure of conforming to this manual or the safety instructions on device label, Vantron assumes neither warranty nor legal liability even if the device is still under warranty. The VT‐IOT‐DONGLE should be installed, debugged and maintained by professional people. The outside antennas are not permitted to be installed or to be changed by ... - Page 6 VT-IOT-Dongle external power source is removed and therefore should not be short‐circuited during transportation or placed under high temperature. Place cables properly: Do not place cables at any place with extrusion danger. Cleaning Instructions Please power off before cleaning the device. Do not use spray detergent. Clean with a damp cloth. Do not try cleaning exposed electronic components unless with a dust collector. Support for special fault: Power off and contact technical support personnel of Vantron in case of the following faults: The device is damaged. The temperature is excessively high. Fault is still not solved after the operation according to the manual. ...
-
Page 7: Overview
VT-IOT-Dongle 2. Overview Front Side View Back Side View Connector window Side View 7/ 21... -
Page 8: Introduction
VT-IOT-Dongle 2.1 Introduction Thank you for choosing Vantron. It is our commitment to provide our valued customers with the embedded devices equipped with the state‐of‐the‐art technology and the best product services. Vantron’s VT‐IOT‐DONGLE products are based on the most advanced ARM and Intel Atom processors and have low‐power consumption and high integration. The products are designed for applications of VT‐IOT‐DONGLE in industrials, medicals, ... -
Page 9: Vt-Iot-Dongle Hardware Instructions
VT-IOT-Dongle 3. VT‐IOT‐DONGLE Hardware Instructions 3.1 Product Appearance RX led TX led Power led Status led Connector SIM CARD ... - Page 10 VT-IOT-Dongle 10/ 21...
- Page 11 120g Weight Black Plastic Box Enclosure Protection IP67 Operating: -10~+55℃, Storage: -20~+70℃ Temperature ETR: -40~+85℃ Optional 5~95%RH at 25-35 (Non-Condensation), Operating and Storage Humidity VT-IoT-Dongle contains FCC ID: RI7LE910NAV2 T-IoT-Dongle-CATM contains FCC ID: 2AJYU-SIM7000A 3.3 Interface Description 11/ 21...
- Page 12 VT-IOT-Dongle 3.3.1 CONNECTOR Connector： 2x5pin,2x2mm Pin1 Pin2 Pin9 Pin10 signal connector RX1+ RX1- TX1+ TX1- RS32_TX RS232_RX VCC_5V VCC_5V SPI_SCK SPI_D0 SPI_D1 SPI_CS RS485_B RS485_A The mating connector reference NSXD S2008H‐2X5P The connect diagram of the mating connector: ...
- Page 13 VT-IOT-Dongle The sample pictures: ...
- Page 14 VT-IOT-Dongle 3.3.3 USB TYPE‐C connector USB type-c connector 3.3.4 BOOT SWITCH Boot switch Pin1~3: 110:Boot from EMMC; 001:boot from SD card; 14/ 21...
-
Page 15: Sd Card &Debug Board(Optional)
VT-IOT-Dongle 3.3.5 SD CARD &DEBUG Connector Connect to debug SD board,1.25mmx12pin SD CARD&DEBUG CONNECTOR UART-TX UART-RX SD_CD DATA3 DATA2 CLK VCC3V3 DATA0 GND DATA1 CMD Default 3.3.6 SD CARD &DEBUG board(optional) SD CARD USB connector Audio Jack to DB9M... -
Page 16: Mounting Hole
VT-IOT-Dongle 3.3.7 Mounting hole ... -
Page 17: Operating Instruction
VT-IOT-Dongle 3.3.8 Operating instruction Install the device with a SIM Card, insert a network cable into the Ethernet port, insert the dedicate 5V DC into the power jack. The device will be powered up within 20 seconds. The system default mode is AP mode. - Page 18 VT-IOT-Dongle Note: Before configure in web page, please confirm the SIM card and antenna: plug the SIM card to the slot of the VT-XOS gateway and connect the antenna for cellular module when gateway is powered off. Steps to confirm your configuration: Step 1.
-
Page 19: Tips
Caution signs in this manual remind of possible danger. Please comply with relevant safety tips below each sign. Meanwhile, you should strictly conform to all safety tips for operation environment. Notice Considering that reasonable efforts have been made to assure accuracy of this manual, Vantron assumes no responsibility of possible missing contents and information, errors in contents, citations, examples, and source programs. Vantron reserves the right to make necessary changes to this manual without prior notice. No part of this manual may be reprinted or publicly released in for ... - Page 20 VT-IOT-Dongle RF exposure warning This equipment must be installed and operated in accordance with provide instructions and the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co‐located or operation in conjunction with any other antenna or transmitter. End‐users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐‐ Reorient or relocate the receiving antenna. ‐‐ Increase the separation between the equipment and receiver. ‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐‐ Consult the dealer or an experienced radio/TV technician for help. ...
- Page 21 Address:440 Boulder Court, Suite 300, Pleasanton, CA 94566 Tel. +1 916-202-7042 Email: sales@vantrontech.com China Office: Chengdu Vantron Technology, Ltd. Address: 6rd floor, 1rd building, No.9, 3rd WuKe East Street, WuHou District, Chengdu, P.R. China 610045 Tel: 86-28-8512-3930/3931, 8515-7572/6320 Email: sales@vantrontech.com.cn...
Need help?
Do you have a question about the VT-IoT-Dongle and is the answer not in the manual?
Questions and answers