hager TRM600AU Quick Start Manual

TR M 60 0A U
0 V 50 Hz
ε 0, 5A AC 1 23
m W
43 3. 5 M hz 10
L/ N
TRM600AU
Radio control for latching relay,
timer
TRM600AU
0,5A AC1 230 V 50Hz
433.5 Mhz 10mW
Metal surfaces in the direct vicinity of the
product (e.g. flush mounted metal boxes)
may reduce the radio range.
Avoid the use of a metal front plate for
switches in combination with flush mounted
metal boxes.
1
z
Complies with
IMDA Standards
DA101847
- The device is to be installed only by a
qualified electrician in accordance with
the installation standards in force in the
country.
- Cut off the 230V power supply before
connecting the device.
The TRM600AU allows to add a radio control to an
existing latching relay or timer circuit powered by
230V. It is a radio receiver which only delivers a
calibrated pulse. It is dedicated to this application
and is placed in a flush mounted box, behind one of
the push buttons of the circuit to control. It connects
in parallel to the push button and consumes equal
to that required by a neon indicator of a push
L/N
button.
The TRM600AU is itself controlled through radio
transmitters. On each command received, its
output contact closes for 200 ms to control the
latching relay or timer in question.
Legend
1 Push button and function LED T of the output
2 Push button and configuration LED
3 Terminal block
Functions
• Single function receiver (pulse) controlled by radio
• 1 pulse output to control a latching relay or timer
In operation :
• Option of manual control of the output: each
press of the T push button = 1 control pulse.
• Display of the output status on the fct LED: 1
single red flash corresponds to 1 pulse of 200 ms.
Quicklink configuration
Quicklink is the name of the tool free Hager
configuration mode for radio products. It uses the
function (fct) and configuration (cfg) buttons and
its Leds, located directly on the products. Only
the "pulse" function (select the timer symbol) and
erasing of the link are available on this product.
Limitations
Only latching relays or timers controlled at 230V
are compatible. In case of use with illuminated
push buttons, the current consumed by the product
must be considered as < than 1mA.
Factory Reset
Press and hold the
LED starts flashing (>10s). The factory reset is
complete when the cfg LED light goes out.
This operation leads to complete erasing of the
product configuration, regardless of the configuration
mode. After switching on or a factory reset, wait for
15 sec. before proceeding with configuration.
This manual is an integral part of the product
O
and must be kept by the end user.
Technical characteristics
Supply voltage
Product consumption
R
Transmission frequency/
Emission power
Dimensions
Max. switch current
Contact closure
duration
Degree of protection
Operating altitude
Pollution degree
Overvoltage category
Operating temperature
Storage temperature
Receiver category 2 / Transmitter duty cycle
<10%
Electric connection:
Hager Controls hereby declares that the radio
transmitter/receiver complies with the 2014/53/
The CE declaration can be consulted
www.hager.com
push button until the cfg
R
230 V +10 %-15% 50 Hz
240 V +6%/-6% 50 Hz
100mW (max. 150mW)
433,05 - 434,79 MHz
10 mW
40 x 40 x 18 mm
0.5A
200ms
IP 20
≤ 2000 m
2
III
-15 °C —> + 45 °C
- 25°C —> + 70 °C
2 2
0,5 mm —> 1,5 mm
2 2
0,5 mm —> 2,5 mm
å
and
EU directive.
on the site:
6LE005074D