Advertisement
Quick Links
Advertisement
Related Manuals for hager Tebis TX 100
Summary of Contents for hager Tebis TX 100
- Page 1 Configuration tool tebis TX 100 How to... / What to do if... 6T 7231a...
- Page 2 Sommaire général How to..........2 Description des touches Dialing and product research phase .
- Page 3 Dialing and product research phase Num. How to... Solutions To order the auto- - Make sure that no output product (wire and radio) is under voltage. matic dialing - Set the configurer in mode 'prog'. outputs. - Make a long pressure of key to start the automatic search of outputs.
- Page 4 Configuration or programming phase How to... Solutions Num. To configure and - For a scenario including rolling shutters or blinds, first set up the lowering time (see set a scenario. item No. 10). - Dial the input intended to activate the scenario to be configured. - Select the scenario function S1 to S8.
- Page 5 Configuration or programming phase How to... Solutions Num. Special case: The position of the shutter is configurable for scenarios 1 to 5. To configure and - Set up the total lowering time of the rolling shutter (see item No.10). set a modifiable - Dial the input intended to activate the scenario.
- Page 6 Configuration or programming phase Num. How to... Solutions To store states of a Since push-buttons on front face of these products do not simulate a long press, it is scenario controlled necessary to use the input simulation mode of TX100 (see §17 page 27 of User’s by a time switch or Instructions TX100) to store the training.
- Page 7 Configuration or programming phase Num. How to... Solutions To link a main dim- - Identify the dimmer switch intended to operate as a Master and carry out a unit mer switch to one factory return (see E17 page 18 of User’s Instructions TX100). or more dimmer - Set the configurer in mode 'prog'.
- Page 8 Configuration or programming phase Num. How to... Solutions activate - Select the desired input (note: the function is not available for all inputs). weather alarm fea- - Assign to it the bad weather alarm function. ture for shutters or - Establish a link between this input and all outputs concerned. blinds.
- Page 9 Others Num. How to... Solutions To locate a pro- See §15 page 26 of User’s Instructions TX100. duct UNIDIR with Recommended procedure to signal an unidir product initiating the indication ‘‘ battery indication of "low low‘ in an installation: battery". - While in mode ‘‘...
- Page 10 Others Num. How to... Solutions To remove the link The link between the input and the local output is factory preconfigured but does not inputs/outputs appear at the time of automatic search. products TR501 It is thus necessary: and TR521. - to dial the input - to assign it a function - to carry out the link with the output concerned.
- Page 11 Dialing and product research phase Num. What to do if... Solutions The dialing of a - Check the wiring of the product. radio input fails. - If not, switch back into mode ' Prog'. - Give the key (a long press (see §3.1 page 9 of TX100 Instructions). - Carry out a new test of dialing.
- Page 12 Configuration or programming phase Num. What to do if... Solutions Note: icon - the number associated with this symbol corresponds to the total number of incom- appears in the left plete or inconsistent remote loadings that have occurred at the time of installation upper corner configuration...
- Page 13 Configuration or programming phase Num. What to do if... Solutions A product - Check in the list '' product information '' (see §3 page 19 of TX100 Instructions) the capacity over- products preceded by: ! range (number of - Select the concerned product using the key links).
- Page 14 Annexes Application Symbole Type de commande Allumage Extinction Marche - Arrêt type interrupteur Marche - Arrêt type télérupteur Marche - Arrêt type télérupteur pour produits unidirectionnels Augmentation du niveau de variation Eclairage Diminution du niveau de variation Variation sur bouton poussoir Forçage Arrêt Forçage Marche Marche temporisée...
- Page 15 Notes...
- Page 16 Hager Tehalit Systèmes SAS 132 Boulevard d’Europe BP 78 F-67212 Obernai Cedex www.hager.com...