Sony CDX-G1200U Service Manual page 5

1-2. Display in Destination Setting Mode
Note: The displayed contents of the following fi gure is an example. The
destination code is different depending on the destination of the
product.
Destination code
1-3. Entering the Destination Code
• Method of operation by main unit
1. Rotate the control dial, and select the alphanumeric character
of "0 to F".
2. The digit advances by pressing the [PUSH ENTER/MENU] or
[ ] button.
> M
The digit returns by pressing the [MODE
ton.
3. The setting is completed by pressing the [PUSH ENTER/
MENU] button at the state of cursor position of "OP0", then
the display turns off, the initialization operation is done, and
the display returns to the clock display.
• Method of operation by remote commander
(Except AEP, UK and HK models)
Note: The model to which the remote commander is not attached can
also be operated by using the remote commander.
1. Press the [ V ] or [ v ] button, and select the alphanumeric char-
acter of "0 to F".
2. The digit advances by pressing the [ b ] or [ENTER] button.
The digit returns by pressing the [ B ] button.
3. The setting is completed by pressing the [ENTER] button at
the state of cursor position of "OP0", then the display turns off,
the initialization operation is done, and the display returns to
the clock display.
OP5 OP4 OP3 OP2 OP1 OP0
6 digits
] or [ ] but-
m .
CDX-G1200U/G1201U/G1202U/G1280UM
1-4. Destination Code
Model Destination OP5 OP4 OP3 OP2 OP1 OP0
US, CND
AEP, UK, HK
E, AUS
CDX-G1200U EA
AR
KR
IND
AEP, UK
E
CDX-G1201U
EA
KR
AEP, UK
CDX-G1202U
EA
CDX-G1280UM IND
2. Confi rmation After Destination Setting
Execute the following operation after completing the destination
setting, and confi rm a correct destination was set.
Destination setting checking method:
1. In the state of source off (the clock is displayed on the liquid
crystal display), enter the test mode by pressing the buttons in
order of the [ 4] t [5] t [
button for two seconds).
Clock display
2. In the state in which the software main version is displayed on
the liquid crystal display (refer to the following fi gure), enter
the destination setting value display mode by pressing the [
SCRL DSPL] button twice (software main version t soft-
ware DSP version t destination code).
(Displayed characters/values in the following fi gure are ex-
ample)
Software main version
3. Confi rm the alphanumeric character of 6 digits on the liquid
crystal display is a value correctly input.
Note: The displayed contents of the following fi gure is an example. The
destination code is different depending on the destination of the
product.
Destination code
4. The resetting operation is executed by pressing the [ OFF
SRC] button for 1 second after the confi rming ends, and the
unit returns to the normal condition.
Display after reset
0 0 9 0 0 2
0 0 9 0 0 1
3 0 B 8 0 0
2 0 9 8 0 4
3 0 B 8 0 3
3 0 9 8 0 0
1 0 9 8 0 0
0 0 9 0 0 1
3 0 B 8 0 0
2 0 9 8 0 4
3 0 9 8 0 0
0 0 9 0 0 1
2 0 9 8 0 4
1 0 9 8 0 0
6] (press only the [
u u
OP5 OP4 OP3 OP2 OP1 OP0
6 digits
6]
5