Page 1
I N S T A L L A T I O N I N S T R U C T I O N S TIL1X2PT TIL1X3PT TIL1X4PT TILVABPT Accessory PT Series LED Wall Mounts / Accessory Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description...
ACCESSORY: AN ACCESSORY is the secondary Chief product which is attached to a primary Chief product, and may have a component attached or setting on it. WARNING: Do not use this mounting system outdoors. COMPONENT:...
Page 3
TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole...
Installation Instructions TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT INSTALLATION Determine location for the top left corner of the LED wall. (See Figure 2) Preinstallation Make a mark 7" below the planned top left corner of the LED wall. (See Figure 2) IMPORTANT ! : Reference the LED screen installation manual for specific instructions regarding care, handling, Using a level, mark a horizontal line across width of LED...
Page 6
TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Installation Instructions Installing First Mount IMPORTANT ! : It is easier to install the vertical connector kit BEFORE the mounts are attached to the The TIL1X2PT / TIL1X3PT /TIL1X4PT (TVF Series) LED wall wall.
Page 7
Installation Instructions TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT IMPORTANT ! : Refer to Fastener Installation Methods Slide the left (A-Left) and right (A-Right) adjustment washers (located in Appendix at end of Installation Instructions) into place behind the partially installed lag screws. (See for details on installing product into various wall types.
Page 8
TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Installation Instructions Adding Additional Mounts 12. Drill pilot holes in centerline of lower slots (see Table 1 for size) and follow fastener information (appropriate for wall Hold additional wall mount against wall ensuring that type) located in Table 1.
Page 9
Installation Instructions TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT 11. Lay levels across flat of the mounting holes and center-of- screen indicators, and vertically along side of mount to ensure wall mount is square and level. NOTE: Lift up slightly on the far side of the second mount to help level the mount.
Page 10
TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Installation Instructions 18. Install the remaining #10 x 1/2" self-tapping screws (G) on 19. Run a string between the self-tapping screws installed in the mount, as necessary, to assist in centering the LED Step 18 to assist with alignment across long sections of housings.
Page 11
Installation Instructions TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Installing Housings and LED Screens Install the first LED housing in the lowest left-hand corner of the video wall by aligning mounting buttons on the housing IMPORTANT ! : Reference the LED screen installation with the mounting holes on the wall mount.
Page 12
TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Installation Instructions Using levels, check the level and plumb of the housings installed on the mounts and adjust as necessary following information in the Adjustments section. 10. Connect housings following instructions included with LED screens.
Page 13
Installation Instructions TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Fastener Installation Methods Steel Stud IMPORTANT ! : See Table 1 for appropriate hardware IMPORTANT ! : See Site Requirements for Steel Stud and pilot hole sizes for various wall types. Installation section before proceeding with Steel Studs IMPORTANT ! : The expanse of the LED wall will most installation to ensure installation site meets requirements!
Page 14
TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Installation Instructions Steel stud Line up anchor with attachment point. (if present) Insert 1/4-20 x 1-3/4" Phillips pan head screw through 1/4" Drywall washer, corresponding mounting hole in wall bracket and into anchor, and tighten until flush against wall bracket. DO Plastic cap NOT over tighten! (See Figure 24) Plastic straps...
Page 15
TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Installation Instructions Site Requirements for Wood or Steel Stud Installation If back side of wall is unfinished, drywall must be installed 16" or 24" (on center) Studs to a minimum of one stud left and right of the stud(s) being used to install the mount.
Installation Instructions TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Configuration Examples The following are just two examples of the many configurations which are possible with the PT Series wall mounts.
TIL1X2PT / TIL1X3PT / TIL1X4PT / TILVABPT Installation Instructions USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Asia Pacific A Office No.
Need help?
Do you have a question about the PT Series and is the answer not in the manual?
Questions and answers