Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eastwood 21304
Summary of Contents for Eastwood 21304
- Page 1 Item #21304 30˝ 3-IN-1 SHEAR, BRAKE & SLIP ROLL INSTRUCTIONS...
-
Page 2: Safety Information
The EASTWOOD 30” 3-IN-1 SHEAR, BRAKE AND SLIP ROLL are three precision engineered metal working tools all rolled into one. It is designed to shear and produce accurate bends and shapes in mild, 20 gauge sheet steel and 18 gauge aluminum in widths up to 30”. Create complex shapes such channels, ribs, patch panels, cones, cylinders and much more in sheetmetal, wire and tubing, all with one convenient bench mount tool. -
Page 3: Read Instructions
• Be sure there is sufficient working room around the tool to allow for safe handling of various sizes of metal. • The Eastwood 3-in-1 Brake, Shear, & Slip Roll was specifically designed to be operated by one person only. Never have one person operate the Handle while another feeds the workpiece or serious injury could occur. - Page 4 SET-UP • The Eastwood Shear, Brake and Slip Roll must be securely mounted on a heavy, solid workbench, stand, floor etc, capable of holding the static weight of the unit plus the stresses from operation. • Place the Shear, Brake and Slip Roll over the chosen location, then mark mounting hole locations by tracing holes in the feet.
- Page 5 """" " " " " Upper Brake Holes Angle Up FIG. 3 """" " " " " Lower Shear Holes Angle Down FIG. 4 10” 8” 6” 3” 2” 1” To order parts and supplies: 800.343.9353 >> eastwood.com...
-
Page 6: Operation
OPERATION The Eastwood 3-in-1 Brake, Shear, & Slip Roll has 3 major metalworking tools designed into one frame. For the purpose of providing the most accurate instruc- tions possible, the 3 major tool functions of Metal Shear, Bending Brake and Slip Roll, with all required adjustments, are described independently as follows:... - Page 7 Set-Up With careful planning, measuring and cutting, many complex sheet metal forms such and boxes, pans, channels and ribs can be created with the Eastwood 3-in-1 unit. NOTE: The factory installed Finger array consists of 1 x 1”, 1 x 2”, 1 x 3” & 1 x 6”, 1 x 8”, & 1 x 10”. In all they total 30”. To configure the Brake: - Select the Finger width or combination of Fingers (N) required to bend the desired width of Sheetmetal.
- Page 8 • Rotate the Hand Crank (Clockwise as viewed from the right side) to form the piece. Continue rotating the hand crank until the entire piece exits the Rollers. NOTE: If a tighter radius is desired, the piece may be re-run through the Rollers with the Rear Roller raised as needed. Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
- Page 9 • Swing the left side of the Upper Roller outward and on an angle but do not try and remove the Roller. Simply slide the work piece off the Roller. • Replace the Upper Roller back into the Thickness Adjustment Screw (R). " " " " FIG. 6 To order parts and supplies: 800.343.9353 >> eastwood.com...
-
Page 10: Maintenance
WIRE AND TUBE ROLLING • The Eastwood 3-in-1 features 3 grooves in the left and right ends of the Lower and Rear Rollers. These are for forming bends into solid wire and tubing. The three sizes of wire and tubing that this tool can be used to form are: 3/16”, 1/8”, and 1/4” [2.2mm, 3.3mm, and 6.3mm]. -
Page 11: Troubleshooting
20 gauge mild steel, or 22 gauge stainless steel. Rollers Slipping/Will Not Feed Metal Upper or Rear Rollers Adjusted Follow Roller Adjustment instructions. Through When Too Loosely and Slipping Handle is Turned To order parts and supplies: 800.343.9353 >> eastwood.com... -
Page 12: Additional Items
#51088 Shrinker/Stretcher Set If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: techelp@eastwood.com PDF version of this manual is available online >> eastwood.com/21304Qmanual The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA US and Canada: 800.343.9353...