Data Output Mode - A&D FC-50Ki Instruction Manual

11-2. Data Output Mode

11-2. Data Output Mode
11-2. Data Output Mode 11-2. Data Output Mode
q The data output modes and parameters are set by F-Functions in f-06
described in the F-Function parameters, section 9.
q To control the scale using commands from an external device, refer to "11-5.
Command Mode Command Mode Command Mode Command Mode".
q Refer to "11-5. Command Mode 11-5. Command Mode 11-5. Command Mode" about the output data format. 11-5. Command Mode
Data Out Mode ( f-06 Data Out Mode (
Data Out Mode ( Data Out Mode (
q Key Mode (f-06/07/08-01
f-06/07/08-01="0") f-06/07/08-01 f-06/07/08-01
When the weight display is stable, data is sent by pressing the PRINT key.
The count display will blink when the data has been sent.
q Stream Mode (f-06
Data is sent continuously. The data-update rate is approximately 10 times per
second for f-06 f-06 f-06 f-06
06 06 06 06 07 07 07 07 08-3="1 1 1 1 " or "2 2 2 2 ", the interval between continuous data is approximately 1.6 08-3 08-3 08-3
/ /
seconds.
q Auto-print Mode A (f-06
Data is sent if the WEIGHT display is stable at +5d (weighing display division) and
above. Next transmission can not occur until after the weight display falls below +5d.
q Auto-print Mode B (f-06
Data is sent if the WEIGHT display is stable at ±5d (weighing display division) and
above/below. Next transmission can not occur until after the weight display falls
between –5d and +5d.
Data to be Sent ( f-06 Data to be Sent (
Data to be Sent ( Data to be Sent (
Select which data is o be sent by keying in a 0 or 1 for the data: Date / time, ID No.,
PCS (count), weight or unit weight.
Example: Key in 0
ID number and the count.
f-06 / / / / 07 07 / / / / 08-01 08-01 ) ) ) )
f-06 f-06 07 07 08-01 08-01
f-06 f-06 f-06 07 07 07 07 08-01 08-01 08-01="1 1 1 1 ") 08-01
/ /
07 07 07 07 08-03="2 2 2 2 ". This rate is same as the display-update rate. For f- 08-03 08-03 08-03
/ /
f-06 07 07 08-01="2 2 2 2 ") 08-01
f-06 f-06 07 07 08-01 08-01
/ /
f-06 07 07 08-01 08-01="3 3 3 3 ")
f-06 f-06 07 07 08-01 08-01
/ /
f-06 / / / / 07 07 / / / / 08-02 08-02 ) ) ) )
f-06 f-06 07 07 08-02 08-02
1 1 0 0 to display 01100, this setting would send only the
# # # #
f-06-02
C o m p a r a t o r
12 34 56 78 C0 00 04 56 78i d
!
2 3 S A M U U W ( g ) 1 2 C l e a r I D
12 34 56 70. 00 00 04 56 789 0 12 34 56 7
# # #
&&
F?I
-00 1 10 0
43
f-06 07 07 08-X as 08-
f-06 f-06 07 07 08- 08-
/ /
'0' not to send data
'1' to send data
Unit weight
Weight
PCS (count)
ID
Date / time
11-5.
11-5. 11-5.
f- f- f-