Part Names - Sharp EC-A1RAS Operation Manual

PART NAMES

MAINTENANCE
Suction head (Rotary brush)
Names of each part and how to assemble
When using the product in the Stick state Removing the dirt
Press Release button to remove respective parts.
Wheel
Right side surface
Rotary brush cover
Napped cushion
Remove the dust attached to the
Suction head with a Duster Nozzle
and cut off the hair and lint
Dust cup assembly
entangled in the
wipe with wrung cloth.
Dust disposal
Remove dirt that became attached to
hook (yellow)
fine parts with a pair of scissor or a pair
of tweezers with thin tips.
Press the Dust disposal hook (yellow) to split the
Dust Cup from the Cover section.
Wash respective filter with water when the Filter care
Cut along the slot of the Rotary brush for
lamp (red) blinks rapidly
removal.
(Do not cut the tips of the bristles of the brush.)
Accessories
Stop using the product when the
becomes worn, check
your nearest service center approved by
Charger (1 unit)
SHARP.
Vacuum cleaner body, Enclosed nozzles and
contacts (terminals) of charging section
Vacuum cleaner body
Wipe with cloth moistened with some water
Enclosed Nozzles
or thinned neutral detergent. Do not use any
paint thinner or benzene product. [Risk of
Duster Nozzle
deterioration or discoloration]
(1 piece)
The vacuum cleaner body,
charger and battery cannot
CAUTION
be washed with water.
EN-5 EN-17
EC-A1RA_Eng_A4(ai sorted).indd 5
Roller
Switch
EN-4, 7
Battery
EN-7
Battery release button
Exhaust port
The built in filter cannot
Rotary brush
be removed.
Cleaning is not
required.
section and then
Cover section
Pleat filter
Filter Cover
Mesh filter
Dust Cup
Dirt accumulates
here.
EN-15, 16
The section Suction head
EN-4
and contact
EN-7 Battery (1 piece)
(Already attached to
Charger at shipping)
Cord
(Approx. 80 cm)
EN-11, 12
Crevice Nozzle
(1 piece)
Suction head, vacuum cleaner body,
Enclosed nozzles and contacts
(terminals) of charging section
When lint, rubber band, hair or pet hair and the like is attached.
Wash with water
When heavily dirtied
After removing the Rotary brush and washing it with water,
remove water and moisture properly and sufficiently dry in
a ventilated location before re-installing.
The Suction head cannot be washed with water in its entirety.
Removal
Remove the Rotary brush cover by sliding the
Release lever to the "OPEN" position.
Rotary brush cover
Remove the belt from the gear while lifting up the
Rotary brush and remove the Rotary brush.
and Pipe described above are also accessories.
Cleaning Brush (1 piece)
(Attached to vacuum cleaner body)
Enclosed nozzles
Wash with water
Plug Adapter
or thinned neutral
detergent.
2-flat-pin adapter
Dry the parts after washing
with water.
Handle / Control switch
Always hold on the handle on the
vacuum cleaner body to transport
the product.Holding onto other parts
(such as a pipe of the Dust Cup) can
dislodge such parts from the vacuum
cleaner body and the product may
fall and lead to injury or product
malfunction.
EN-9
Lamps EN-6
Back side
Holder
section
EN-10, 19
Cup release
lever (black)
Release lever
EN-13
Release button
Pipe
Release button
Suction head EN-17
Belt
Remove
the belt
Gear
Attach the brush in the direction
shown in the diagram after use.
When heavily dirtied
(1 piece)
Use the adapter if your
EN-16
outlet is for 2-flat-pin plug.
This adapter is not used
in Singapore.
2017/07/21
CA
A
Co
Wi
wit
10:00:55