Sharp EC-A1RAS Operation Manual page 11

Parts that may be washed with water
EN-17
Cleaning the Filters
Pleat Filter
Dislodge and remove dirt and dust by
dusting.
Insert the battery into the vacuum cleaner body.
Dust in the direction illustrated in
the diagram on the right as dirt
Remove the battery
tends to accumulate on the back
side. from the charger.
Do not use a cleaning brush
[Risk of damages].
4
Mesh filters (Upper and Lower), Filter Cover
Remove dirt and dust with a cleaning brush.
Gently rub
the mesh.
When heavily dirtied, wash with water.
Notices
Pleat filter
In cases where charging is not possible, verify followings.
Is the power plug of the charger dislodged?
Is the battery correctly set to the charger?
Carefully wash
Information on Charging
the back side.
The charging time may be long in following cases.
When not in use for long period of time
Wash with water or thinned neutral detergent.
The battery is charged in an environment at a low temperature (approx. 5°C or lower) or a high temperature
(approx. 35°C or higher) (charge the battery in an environment with at room temperature between 5°C and 35°C).
Filter Cover Mesh filter
Information on operating time
The operating time gradually becomes shorter as the
battery is used repeatedly.
When the remaining charge in the battery becomes low, the
Battery level indicator lamp (green) blinks to notify the
status.
Dry the parts after washing with
The Charging lamp (red) of the charger blinks slowly)
water.
If the blinking occurs when the room temperature is between 5°C and 35°C, then it is time to replace the battery.
Thoroughly dry prior to assembling.
There is no malfunction if the product blinks in an environment with a low temperature (about 5°C or lower) or a high
[Risk of filter clogging not improving even after
temperature (about 35°C or higher). Charge the battery in an environment that is between 5°C to 35°C.
cleaning.]
When the Charging lamp (red) of the charger rapidly blinks, that may be caused by malfunction of the charger,
Properly remove moisture, gently wipe off moisture
or deterioration or malfunction of the battery. Contact your nearest service center approved by SHARP.
with a towel or the like, dry in shade at a well
ventilated location to thoroughly dry.[Risk of
emission of odor or product malfunction.]
Estimated 12 hours.
drying time: (This may vary depending on
the environment and season.)
Do not apply any hot air, such as air blown by a hair dryer.
[Risk of deformation or product malfunction.]
EC-A1RA_Eng_A4(ai sorted).indd 8
EN-17 EN-17
Top side
Insert the battery
into the vacuum
cleaner body.
When the odor stands out,
dilute bleach for clothing in
water and immerse the filter
in this solution following
instruction for the bleach,
then rinse with
water.
Dust Cup
Warning
Always do followings during maintenance
Press the to stop the operation of the product
and remove the battery.
Disconnect the power cord of the charger from the
electrical outlet.
[Risk of electrocution or injury.]
Assembling the Filters
Install the Filter Cover and the Mesh
1
filters (Upper and Lower).
Align the
positions..
Securely insert the battery along the
grooves on the vacuum cleaner body until
the "click" sound is emitted.
Once the terminals are connected, the Battery Level
Indicator lamp on the vacuum cleaner body turns on
for about five seconds to notify the remaining
charge in the battery. Be sure to securely insert the
Click!
battery until the "click" sound is heard, even if the
lamp starts to light up during the process.
Align the
positions..
2
Align the salient part of the Pleat
filter to the recessed section of the
Filter Cover and press in.
Is there any dirt or foreign matter attached to a terminal of
the charger or the battery? Remove the dirt or foreign
matter with dry cloth. EN-17, 18
Salient
section
Install the Dust Cup.
3
Install the Dust Cup.
Continuous operation time*
About 8
Align the protrusion on the Dust Cup and the
High mode
minutes
Dust disposal hook (yellow) and insert.
About 30
EN-6
Standard mode
minutes
Dust
disposal
hook
(yellow)
Protrusion
Each part must be assembled
correctly in order for them to fit onto
CAUTION
the vacuum cleaner body.
Caution is required to ensure that the
Mesh filters (Upper and Lower) are
not lost while throwing out dirt or
cleaning.
Turn
Turn
Slot
Align the
terminals.
Recessed
section
When a single battery is used
(fully charged and initial condition
of the battery / 20°C). Conditions
may vary depending on the
material of the floor surface,
environment in which the product
is used and the condition under
which the product is used.
EN-4
Click!
EN-16 EN-8
2017/07/07 11:43:19