Page 4
Remove the clogging dirt. insulation defects due to humidity and the like, which location with high Contact your nearest service center approved by SHARP if the product still stops during cleaning even can cause fire disaster.) temperature such as inside if the measures described above have been implemented.
Page 5
If the Filter care lamp (red) and the Battery level indicator lamp (green) on the vacuum cleaner body are blinking Rotary simultaneously the product may be malfunctioning. Contact your nearest service center approved by SHARP . brush Charger...
Back side Do not immerse or wet the product with water. Do not use any charger for a battery that is not specified by Sharp. (Risk of heating, smoke generation, bursting, ignition of fire or liquid leakage.) Holder Always use a battery that is specified by Sharp.
Page 7
This cordless vacuum cleaner is intended for Do not apply lubricant to the Rotary brush (Risk of Replace only with same SHARP Corporation type BY-5SB battery pack. household use and must not be used for commercial plastic parts cracking).
Charger (1 unit) EN-7 Battery (1 piece) Cleaning Brush (1 piece) the belt Gear SHARP. (Already attached to (Attached to vacuum cleaner body) Charger at shipping) Attach the brush in the direction Cord shown in the diagram after use.
Page 9
About 1,100 times of charge/discharge ◆ Click! According to tests conducted based on Sharp's standard Release for repeatedly charging and charge/discharge a battery. The life of a battery can vary depending on the conditions button of use and the environment.
MAINTENANCE PREPARATION EN-6 Dust cup assembly tips for making the battery last. Guide for cleaning Charging battery Removal Dispose of dirt and remove the dirt and The battery is not charged when the product is purchased, so the battery must be removed from Remove the Dust Cup.
Page 11
Properly remove moisture, gently wipe off moisture Protrusion or deterioration or malfunction of the battery. Contact your nearest service center approved by SHARP. with a towel or the like, dry in shade at a well ventilated location to thoroughly dry.[Risk of Each part must be assembled emission of odor or product malfunction.]...
Page 12
VACUUMING EMPTYING THE DUST CUP Guide for disposing Removal Flow of cleaning process of dirt Removing the Dust cup assembly Start When the level of the accumulated Control The mode toggles between the "High mode" and the "Standard dirt reaches the "MAX" line. Cup release lever switch Pull the...
Page 13
Mounting the Dust Tips for Vacuuming Emptying the Dust Cup Cup Assembly Remove the Dust Cup and dispose of Install the Dust cup assembly the dirt. on the vacuum cleaner body. Stick state Handy state Move the Suction head so that it moves Press the Dust disposal lightly and glides slowly.
VACUUMING Using accessory nozzles (Duster nozzle and Crevice nozzle) Duster nozzle The accessory may be used by attaching on the vacuum cleaner body or on a pipe. For cleaning high places, such as above furniture. Do not press the while operating when cleaning with the vacuum cleaner body facing up.
Page 15
Do not use the product to clean items that scratch easily, such as a piano. Using Accessory Suction Inlet (Duster nozzle and Crevice nozzle) Crevice nozzle The accessory may be used by attaching on the vacuum cleaner body or on a pipe. For cleaning gaps between furniture and sash on the windows.
EMPTYING THE DUST CUP VACUUMING Guide for disposing Removal Flow of cleaning process of dirt Removing the Dust cup assembly Start When the level of the accumulated Control The mode toggles between the "High mode" and the "Standard dirt reaches the "MAX" line. Cup release lever switch Pull the...
Page 17
Mounting the Dust Tips for Vacuuming Emptying the Dust Cup Cup Assembly Remove the Dust Cup and dispose of Install the Dust cup assembly the dirt. on the vacuum cleaner body. Stick state Handy state Move the Suction head so that it moves Press the Dust disposal lightly and glides slowly.
Page 18
MAINTENANCE PREPARATION EN-6 Dust cup assembly tips for making the battery last. Guide for cleaning Charging battery Removal Dispose of dirt and remove the dirt and The battery is not charged when the product is purchased, so the battery must be removed from Remove the Dust Cup.
Page 19
Properly remove moisture, gently wipe off moisture Protrusion or deterioration or malfunction of the battery. Contact your nearest service center approved by SHARP. with a towel or the like, dry in shade at a well ventilated location to thoroughly dry.[Risk of Each part must be assembled emission of odor or product malfunction.]...
Charger (1 unit) EN-7 Battery (1 piece) Cleaning Brush (1 piece) the belt Gear SHARP. (Already attached to (Attached to vacuum cleaner body) Charger at shipping) Attach the brush in the direction Cord shown in the diagram after use.
Page 21
About 1,100 times of charge/discharge ◆ Click! According to tests conducted based on Sharp's standard Release for repeatedly charging and charge/discharge a battery. The life of a battery can vary depending on the conditions button of use and the environment.
Back side Do not immerse or wet the product with water. Do not use any charger for a battery that is not specified by Sharp. (Risk of heating, smoke generation, bursting, ignition of fire or liquid leakage.) Holder Always use a battery that is specified by Sharp.
This cordless vacuum cleaner is intended for Do not apply lubricant to the Rotary brush (Risk of Replace only with same SHARP Corporation type BY-5SB battery pack. household use and must not be used for commercial plastic parts cracking).
Remove the clogging dirt. insulation defects due to humidity and the like, which location with high Contact your nearest service center approved by SHARP if the product still stops during cleaning even can cause fire disaster.) temperature such as inside if the measures described above have been implemented.
Page 25
If the Filter care lamp (red) and the Battery level indicator lamp (green) on the vacuum cleaner body are blinking Rotary simultaneously the product may be malfunctioning. Contact your nearest service center approved by SHARP . brush Charger...
Need help?
Do you have a question about the EC-A1RAS and is the answer not in the manual?
Questions and answers