Sharp EC-A1RAS Operation Manual page 25

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
If the Cord of the Charger is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
The Suction head and Pipe (accessories) are only to be used with the appliance. Do not connect these accessories with
Symptoms
the power outlet or plug, socket-outlet, connector or appliance inlet that is connected with the power outlet.
■ Details on the types of matters that must be observed are
The temperature of the vacuum cleaner body can rise to about 40°C during operation, but this is
explained using following symbols.
not abnormal.
rs with
The vacuum cleaner
or Do not do this
body is hot
y".
The charger or the
battery becomes hot
while charging.
The Dust cup assembly
cannot be installed on
the vacuum cleaner body
When product is used
Never modify the structure of the vacuum
nce
The Dust cup
cleaner body or the charger and do not
assembly cannot be
disassemble and no one must repair the
assembled.
product unless the individual is a repair
technician.
(Risk of fire disaster, electrocution or injury.)
Contact your nearest service center approved by
SHARP.
Do not touch the terminals of the charger
or the battery while charging or
wet
immediately after completing charging.
The Rotary brush
(Risk of burns.)
does not rotate.
ure
o be
Do not touch the terminals of the vacuum
cleaner body, the charger or the battery with
a metal object such as a needle or a pin.
(Risk of heating, ignition of fire, electrocution or
product malfunction.)
A rattling sound is
do
coming out of the
Suction head.
ter).
The air discharged
from the vacuum
cleaner body smells.
Terminal
A part of the Pleat
Do not touch the Rotary Brush or Roller
filter appears to be
Switch (with safety stop mechanism).
white and floating.
(Risk of injury of a hand or the like.)
Be particularly careful with children!
If the Filter care lamp (red) and the Battery level indicator lamp (green) on the vacuum cleaner body are blinking
simultaneously the product may be malfunctioning. Contact your nearest service center approved by SHARP .
Must do the followings when servicing
or inspecting the product
est
EC-A1RA_Eng_A4(ai sorted).indd
Is there any clogging on the Mesh filters or Pleat filter?
Must do this
Heat is generated due to the electrical current that is supplied to the
control circuit, but this is not abnormal.
Are respective components of the Dust cup assembly assembled
properly?
Is there any dirt accumulating at the bottom of the Dust Cup?
Is there any dirt entangled on the Mesh filters?
Is the Pleat filter properly installed to the Filter Cover?
Are respective components of the Dust cup assembly assembled properly?
The Rotary brush stops automatically for safety purpose when the
Suction head is off the floor. (Safety Stop)
Is the pipe dislodged from the vacuum cleaner body?
Is any hair or lint tangled on the brush?
The Rotary brush may stop in some instances as the automatic stop
function is triggered when the Suction head becomes stuck on a surface
when the product is used to clean carpets and mats on which the Suction
head can become closely attached and blocked. In such instances, turn
off the product.
The automatic stop function will be released and the product can then be
used again.
Is the Suction head assembled properly?
This is a sound emitted by the Roller Switch, due to the structure
(safety stop mechanism).
This is not abnormal.
Is there much dirt accumulating in the Dust Cup?
(Depending on the type of accumulated dirt some odor may be emitted.)
Has the Mesh filters or the Pleat filter been washed with water and then
sufficiently dried? [Using the product while moisture remains on or in the
product may lead to the emission of an odor]
Terminal
The white filter material can become visible at times, but there is no quality
issue with such a situation.
Roller
Switch
Rotary
brush
Press the and remove the battery
from the vacuum cleaner body.
Disconnect the power cord of the charger
from the electrical outlet.
(Risk of electrocution or injury.)
22
Check details described
below
for repairs or contacting
for inquiries).
Check here
Caution
When product is used
EN-7
Terminal
Charger
Remove
the plug
(prior to requesting
Matters for preventing electrocution,
fire disaster and malfunction of
vacuum cleaner body
Do not block the air exhaust port
Do not operate the product over a
long period of time with the Suction
head blocked.
(Risk of deformation of vacuum
cleaner body, ignition of fire
and fire disaster due to
overheating.)
Do not allow any metal objects or pins to
enter in the pipe insertion slots, pipe
contacts or air exhaust port.
(Risk of electrocution and
malfunction of product.)
Pipe contact
Do not transport the product by
holding on a pipe or the Dust Cup.
(Risk of injury or malfunction of product
when the vacuum cleaner body becomes
dislodged or falls.)
Be sure to remove the power plug from
the power outlet by holding onto the
power plug with a hand.
(Risk of electrocution, short circuiting and ignition
of fire.)
Disconnect the power cord of the product
from the electrical outlet when not using
the product over a long period of time.
(Risk of electrocution, electric current leakage and
fire disaster due to deterioration of insulation.)
Reference
Pages
EN-15, 16
−
EN-16
EN-14
EN-16
EN-16
EN-16
EN-9
−
EN-17
−
EN-17
−
EN-13, 14
EN-15, 16
−
EN-2
EN-22
2017/07/07 11:43:22