pronovost P-INV-74 Operator's & Parts Manual page 20

SNOWBLOWER P-INV-74 (cont'd)
REF. PART #
1 120-07642
2 140-25432
2 140-25432
3 319-38280
3 319-38280
4 300-40280
5 130-81581
6 UCPE208-24
7 110-44301
8 300-44355
9 110-44242
10 110-44282
11 300-36250
12 6253
13 300-40520
14 300-40490
15 Std.
16 150-06012
17 300-40460
18 110-44233
19 110-44234
20 140-25941
21 300-40340
22 110-33781
23 110-44372
24 130-83744
25 130-83743
26 300-32220
27 Std.
28 Std.
29 300-46370
30 Std.
31 8186
32 336-44000
33 110-44401
34 300-40415
35 300-36250
36 110-45522
37 110-45512
38 300-40280
39 300-40310
40 130-81811
41 UCFD207-20
42 190-12331
42 26A60
42 59-60
43 160-26791
44 160-26501
45 300-32310
46 110-44351
10
47 160-26511
48 110-44342
49 110-44292
50 8030
51 8251
52 140-10571
DESCRIPTION
Frame P-INV-74 ......................................................................................................
Scraper blade 3/8" x 2 1/2" x 72 3/4" lg standard steel ..............................................
Scraper blade 3/8" x 2 1/2" x 72 3/4" lg standard steel (rear mount scraper blade) ......... opt.
Plow bolt 7/16" NC x 1 1/4" lg + lockwasher ...........................................................
Plow bolt 7/16" NC x 1 1/4" lg + nut & lockwasher (rear mount scraper blade) (8) ......... opt.
Bolt 1/2" NC x 1 1/4" lg .........................................................................................
Shaft end retainer ....................................................................................................
Bearing 1 1/2" .......................................................................................................
Adjustment plate for impeller shaft + 2 nuts 1/2" NC ..................................................
Bolt 5/8" NC x 2 1/4" lg .........................................................................................
Impeller 26" ø x 9" - 4 blades .................................................................................
Impeller shaft ..........................................................................................................
Bolt 3/8' NC x 1" lg + nylon locknut ........................................................................
Pin category 1 ........................................................................................................
Bolt 1/2" NC x 5" lg + nylon locknut .......................................................................
Bolt 1/2" NC x 4 1/2" lg + nylon locknut .................................................................
Hitch pin clip 5/32" ................................................................................................
Pin (top link) ...........................................................................................................
Bolt 1/2" NC x 4" lg + nylon locknut .......................................................................
Right lower hitch .....................................................................................................
Left lower hitch .......................................................................................................
3-points side bar .....................................................................................................
Bolt 1/2" NC x 2" lg + nylon locknut .......................................................................
Hoses support ........................................................................................................
Upper hitch ............................................................................................................
Right guard ............................................................................................................
Left guard ..............................................................................................................
Bolt 1/4" x 3/4" lg + nylon locknut ..........................................................................
Grease fitting 1/4" - 28 straight ................................................................................
Hitch pin clip 1/8" x 2 9/16" ...................................................................................
Bolt 3/4" NC x 2 1/2" lg + nylon locknut .................................................................
Grease fitting 1/4" - 28 elbow 90 deg. .....................................................................
Idler sprocket # 60 ..................................................................................................
Nut 5/8 NC ............................................................................................................
Idler ......................................................................................................................
Bolt 1/2" NC x 3 1/4" lg + nylon locknut .................................................................
Bolt 3/8" x 1" lg + nylon locknut .............................................................................
Interior chain guard (center) ......................................................................................
Interior chain guard (front) ........................................................................................
Bolt 1/2" x 1 1/4" lg + flat washer + nylon locknut ...................................................
Bolt 1/2" x 1 1/2" lg + nylon locknut .......................................................................
Mounting plate for drive ass'y ...................................................................................
Bearing 1 1/4" + flange & 2 grease fitting straight ......................................................
Chain #60 45 3/4" lg 61 links ................................................................................
Connecting link #60 ................................................................................................
Offset link #60 .......................................................................................................
Spacer for drive shaft ...............................................................................................
Brass bushing 1 1/4" i.d. x 1 1/2" o.d. x 5/8" lg .......................................................
Bolt 1/4" NC x 1 1/2" lg grade 5 + nylon locknut ......................................................
Sprocket #60 + shearplate (including no. 44 & 47) ....................................................
Brass bushing 1 1/4" i.d. x 1 1/2" o.d. x 5/8" lg .......................................................
Auger drive shaft 27 3/32" lg hors tout (including no. 89) ...........................................
Auger ....................................................................................................................
Key for gearbox ......................................................................................................
Gear box T27D ......................................................................................................
Back plate ..............................................................................................................
- 20 -
QTY
1
1
8
1
1
1
1
2
1
1
4
2
2
2
3
1
2
1
1
2
3
1
1
1
1
1
3
4
1
2
2
1
1
1
6
1
1
3
4
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1