Maintenance - eisenblatter VARILEX 1802 HT Original Instructions Manual

Machines with paddle switch
(with dead man function):
I
Switch on: Slide the switch­on lock (9) in the direction of
the arrow and press the trigger (9).
Switch off: Release the trigger switch (9).
Continuous duty
I
Switch on: Switch the machine on as described
above. Now slide the trigger switch (9)
forwards again and release in the front
position to lock the trigger switch (9)
(continuous operation).
Switch off: Push the trigger switch (9) upwards
and release.
7.3 Working Directions
Grinding and sanding operations:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Grinding with grinding fl aps discs:
position the machine at an angle of 30° ­ 40° for the
best working results, apply moderate pressure.
Cutting-off operations:
Always work against the run of the disc
(see illustration). Otherwise there is the dan­
ger of the machine kicking back from the cut
out of control. Guide the machine evenly at a
speed suitable for the material being processed. Do not
tilt, apply excessive force or sway from side to side.
Wire brushing:
Press down the machine evenly. Let the wire brushes
work.
8. Dust Prevent System and Cleaning
8.1 Dust Prevent System (DPS)
Your machine is already equipped with the Dust Prevent
System (DPS) by Eisenblätter. The DPS is a permanent
instalment to the rear ventilation intakes of the machine.
It has been developed utilizing aerodynamic particle
simulation and its application is widely maintenance free
compared to other standard covering ventilation caps.
The DPS can effectively assist in the reduction of hostile
particle accumulations in the machines internals while
in normal working operation. The functional principle is
20
9
0
9
0
based on the fundamentals of aerodynamics in conside­ based on the fundamentals of aerodynamics in conside­
ration of the course a particle (metal cuttings e.g.) travels ration of the course a particle (metal cuttings e.g.) travels ration of the course a particle (metal cuttings e.g.) travels ration of the course a particle (metal cuttings e.g.) travels
from its point of creation (spindle) to the ventilation from its point of creation (spindle) to the ventilation from its point of creation (spindle) to the ventilation from its point of creation (spindle) to the ventilation from its point of creation (spindle) to the ventilation
intakes of the machine. intakes of the machine. intakes of the machine.
Mit DUST PREVENT SYSTEM: DUST PREVENT SYSTEM:
Ideale Wärmeabfuhr und Ideale Wärmeabfuhr und
vor Feinstaub geschützter Motor vor Feinstaub geschützter Motor
Ohne DUST PREVENT SYSTEM: DUST PREVENT SYSTEM:
Heiße Luft und Feinstaub gelangen Heiße Luft und Feinstaub gelangen
in das Innere der Maschine in das Innere der Maschine
Ensure good ventilation of the workspace and use an Ensure good ventilation of the workspace and use an
extraction unit and/or air purifi er, extraction unit and/or air purifi er,
for the DPS's ability to reduce particles to reach the
internals of the machine of your personal workspace not
particles that enriched the air surrounding you.
Using the machine without the DPS is not advisable due
to altered geometries at the ventilation intakes.

Maintenance:

Clean the machine as 8.2 describes.
Hereby point the compressed or vacuumed air pistol right
at the circular intake of the DPS.
After long usage it may be advisable to clean machine
parts beneath the DPS.
Unscrew the placement screw on the lower end of the
DPS for a few turns and push the DPS towards the gear
housing (pos. 54). Clean the area with dry air and/or a
cloth. Fix the DPS is opposite direction.
Be aware of the tab location that will lock the DPS in
place in one continuous line beginning at the speed dial
on the machines handle.
8.2 Cleaning
While working on different materials it is possible that
particles deposit inside the power tool. Clogging may
compromise the cooling of your power tool. Conductive
build­up can impair the protective insulation of the power
tool and cause electrical hazards. The power tool should
be cleaned regularly, often and thoroughly through all
front and rear air vents using a vacuum cleaner or by blo­
wing in dry air. Prior to this operation, separate the power
tool from the power source and wear protective glasses
and dust mask.
EN