Equipment And Accessories; Maintenance - eisenblatter PIPE MAX 802 HT Original Instructions Manual

EN
8. Dust Prevent System and Cleaning
8.1 Dust Prevent System (DPS)
Your machine is already equipped with the Dust Prevent
System (DPS) by Eisenblätter. The DPS is a permanent
instalment to the rear ventilation intakes of the machine.
It has been developed utilizing aerodynamic particle
simulation and its application is widely maintenance free
compared to other standard covering ventilation caps.
The DPS can effectively assist in the reduction of hostile
particle accumulations in the machines internals while
in normal working operation. The functional principle is
based on the fundamentals of aerodynamics in conside-
ration of the course a particle (metal cuttings e.g.)
travels from its point of creation to the
ventilation intakes of the machine. ventilation intakes of the machine.
With DUST PREVENT SYSTEM: DUST PREVENT SYSTEM:
Ideal heat dissipation and Ideal heat dissipation and
motor protected from particulate matter motor protected from particulate matter
Without DUST PREVENT SYSTEM: DUST PREVENT SYSTEM:
Hot air and particulate matter Hot air and particulate matter
reach the machine´s interior reach the machine´s interior
Ensure good ventilation of the workspace and use an Ensure good ventilation of the workspace and use an
extraction unit and/or air purifi er,
for the DPS's ability to reduce particles to reach the
internals of the machine of your personal workspace not
particles that enriched the air surrounding you.
Using the machine without the DPS is not advisable due
to altered geometries at the ventilation intakes.

Maintenance:

Clean the machine as 8.2 describes.
Hereby point the compressed or vacuumed air pistol right
at the circular intake of the DPS.
After long usage it may be advisable to clean machine
parts beneath the DPS.
Unscrew the placement screw on the lower end of the
DPS for a few turns and push the DPS towards the gear
housing (pos. 54). Clean the area with dry air and/or a
cloth. Fix the DPS is opposite direction.
Be aware of the tab location that will lock the DPS in
place in one continuous line beginning at the speed dial
on the machines handle.
8.2 Cleaning
While working on different materials it is possible that
particles deposit inside the power tool. Clogging may
compromise the cooling of your power tool. Conductive
build-up can impair the protective insulation of the power
tool and cause electrical hazards. The power tool should
be cleaned regularly, often and thoroughly through all
front and rear air vents using a vacuum cleaner or by blo-
wing in dry air. Prior to this operation, separate the power
tool from the power source and wear protective glasses
and dust mask.
9. Troubleshooting
The machine does not start.
The electronic signal display fl ashes.
The restart protection is active. If the mains plug is
inserted with the machine switched on, or if the power
supply is restored following an interruption, the machine
does not start up. Switch the machine off and on again.

10. Equipment and accessories

10.1 Five-fold rocking hand grip
The rocking handle of the power tool
can be secured in fi ve different posi-
tions. Using different angles of the
forward hand grip eases work load in
different working positions. For right-
and left-handed users. To tilt the
handle, unscrew the handle for a few
turns, bring the handle in the desired position, lock the
handle by screwing it snug.
10.4 Accessories
Use genuine Eisenblätter accessories.
Use only accessories which fulfi l the requirements
and specifi cations listed in these operating instructions.
Cutting guard clip / guard for cut-off grinding
Designed for work with cutting disc and diamond
cutting discs. Once the cutting guard clip is fi tted,
the safety guard becomes a cutting guard.
Accessories PIPE MAX 802 HT
Item
38663
Ball joint mount
38702
Accessory set coarse grinding to perfect mirror fi nish
50104
Solid heavy-duty transport case
11. Repairs
Repairs to electrical tools must be carried out
by qualifi ed electricians ONLY!
If the connection lead is damaged, it must be
replaced by a new connection lead.
Contact your Eisenblätter representative if you
have Eisenblätter power tools requiring repairs.
You can download a list of spare parts from
www.eisenblaetter.de
Description
15