Download Print this page

Sharp AH-XPC9RV Installation Manual

Split type room air conditioner
Hide thumbs

Advertisement

Quick Links

SPLIT TYPE ROOM AIR CONDITIONER
INSTALLATION MANUAL
This manual describes the installation of indoor unit only
For the installation of the outdoor unit, see the installation manual accompanying outdoor unit.
SAFETY PRECAUTIONS
• Installation must be made in accordance with the installation
manual by
service personnel.
• Be sure to use the attached accessories parts and
for installation.
falling.
• The appliance shall be installed in accordance with national wir-
ing regulations.
• After installation has complete, check that there is no leakage of
refrigerant gas.
• Ventilate the room if refrigerant gas leaks during installation.
• Use the
electrical cable.
Make sure the cable is secured in place and that the terminals are free
result.
• Form the cable so that the control box cover, the cord holder and
cable holder are not loose.
ACCESSORIES
ITEMS
Q'ty
APPLICATION
1 MOUNTING PLATE
To mount the indoor
4 DRY BATTERY
unit on the wall.
1
2 LONG SCREW
5 SHORT SCREW
(M4.5x30)
plate with the wall
(M4x20)
7
plugs.
3 REMOTE CON-
To control remotely.
TROL
1
INSTALLATION DIAGRAM
50 mm or more
50 mm or more
50 mm or more
Coating tape
(Commercially
70 mm or more
available)
Provide as much installation space as possible for
Use the refrigerant pipes shown in the table below.
Pipe
Pipe size
Thermal insulation
thickness
Liquid
1/4"
Thickness:
side
(ø 6.35 mm)
6 mm or thicker
0.8 mm
Gas
3/8"
Material:
side
(ø 9.52 mm)
Polyethylene foam
• The thermal insulation should cover both the gas and liquid
pipes.
A3AHXPC9_2RV_B510.indd 1
AH-XPC9RV
AH-XPC12RV
• Tighten the
nut with a torque wrench according to the
method.
long time and cause refrigerant gas leakage.
parts
• When installing the unit, take care not to enter air substance other
than the
refrigerant(R410A) in the refrigerant cycle.
Otherwise, it will cause burst and injury as a result of abnormal high pres-
sure in the refrigerant cycle.
• Be sure to connect the refrigerant pipe before running the compres-
sor.
Otherwise, it will cause burst and injury as a result of abnormal high pres-
sure in the refrigerant cycle.
• Earth the unit.
Incomplete earth may cause electrical shock.
• Install an earth leakage breaker to avoid electric shock in case of
leak.
Use the current-activated, high-sensitivity, high-speed type breaker with a
rated sensitivity current of below 30 mA and an operating time of below 0.1
second.
• Arrange the drain hose to ensure smooth drainage.
• This room air conditioner uses refrigerant R410A.
Use the
ITEMS
Q'ty
APPLICATION
ITEMS
For the remote con-
6 REMOTE CONTROL
trol.
HOLDER
2
AAA batteries.
REMOTE
7 CABLE COVER
CONTROL HOLD-
2
ER.
8 MANUALS
COVER
1
NOTES ON LOCATIONS
1.
entire room.
2. Make a drain hose hole for easy drainage.
3.
both sides and above the unit.
4.
5. Keep TV set, radio and the like 1 m or more away from the unit and the remote
control.
6. Keep the air inlet clear of obstacles that could block incoming air.
7. The remote control may not function properly in a room equipped with an electronic
lighting.
8. Select a location that does not cause loud operation noise and extreme vibrations.
INSTALLATION DIMENSION OF INDOOR UNIT
(unit size)
860
175
Outline of indoor unit
I
D
I
D
A
F
108
115
Center of wall hole
A
F
Carefully read and follow these instructions for
smooth and trouble-free installation.
B510
1
PLACING THE MOUNTING PLATE AND MAKING A PIPING HOLE
Installing the mounting plate
(1) Referring to the "INSTALLATION
DIMENSION OF INDOOR UNIT",
holes and the piping hole.
marked in circle around the hole.
(7 points)
• Make sure that the mounting
plate is horizontally.
(2) Secure the mounting plate to the
wall with the long screws and
check the stiffness.
2
SETTING UP THE INDOOR UNIT
Piping route
.
without leaving any sharp edge.
(Keep the cut-out plate for possible future use.)
Q'ty
APPLICATION
To mount the remote
control on the wall.
1
Mounting the indoor unit
For right side piping
To secure the cable.
(1) Pass the pipes and the drain hose through the
1
piping hole.
(2) Hook the unit onto the mounting plate.
1
Installation manual
(3) Pull the connecting cable into the indoor unit.
1
Operation manual
(4) Push the unit and apply the bottom hooks to the
mounting plate's support.
(5) Pull the bottom of the unit to check that the unit
For left side piping
(1) Reverse the positions of the drain hose and
drain cap. Refer to "Exchange the drain hose".
(2) Connect the pipes and wrap tape around the in-
sulation of the piping joints tightly not to become
thick.
(3) Bind the pipes and connecting cable with tape.
(4) Set the pipes and connecting cable along the
back of the unit, and attach the piping holder.
(5) Pass the pipes, connecting cable and the drain
hose through the piping hole.
125
(6) Hook the unit onto the mounting plate.
J
(7) Push the unit and apply the bottom hooks to the
E
mounting plate's support.
E
(8) Pull the bottom of the unit to check that the unit
J
Notes:
• Bend the pipes carefully as not to damage them.
• Lay the drain hose below the pipes.
Center of wall hole
Length unit: mm
Making a piping hole
(1) Drill a piping hole
with 70mm diameter
concrete drill or a hole
saw with a 5mm down
ward slant to the out-
side.
(2) Set the sleeve and
2 LONG SCREW
caps.
1 MOUNTING PLATE
zone
Plate
Plate
Cut the plate along
notch.
Plate
MOUNTING PLATE
Taping
Hook
MOUNTING PLATE
Exchange the drain hose
Drain Hose
(1) Remove the screw and pull out the drain
hose.
Drain Cap
Tape
(2) Pull out the drain cap.
Insulation
(3) Reconnect the drain hose to the right
and insert the drain cap to the left.
Pipes
• Fully insert the drain hose until it stops and
• Insert a hexagon wrench (4 mm diagonal)
into the drain cap, and press it fully.
Drain Hose
Tape
Piping holder
Caution:
After replacing, make sure that both the drain
ENGLISH
Wall
Outdoor
Indoor
Cut with a saw.
Cap
5 mm
Sleeve
(Downward to
outdoor)
Screw
Drain Hose
Drain Cap
Screw
Hexagon wrench
Drain Hose
Drain cap
2011-8-11 8:13:41

Advertisement

loading

  Also See for Sharp AH-XPC9RV

  Related Manuals for Sharp AH-XPC9RV

  Summary of Contents for Sharp AH-XPC9RV

  • Page 1 • Form the cable so that the control box cover, the cord holder and cable holder are not loose. Piping route • This room air conditioner uses refrigerant R410A. zone Use the without leaving any sharp edge. (Keep the cut-out plate for possible future use.) ACCESSORIES Plate Plate Cut the plate along notch.
  • Page 2 CONNECTING THE CABLE TO THE INDOOR UNIT HANGING THE REMOTE CONTROL Fix the remote control holder Use a copper cable.(Cross-section area 1.0 mm to the wall with the short 50 mm screws. 40 mm ible cord (code designation 60245 IEC 57). 8 mm 6 REMOTE CONTROL (1) Process the end of the connecting cable for the indoor side.

This manual is also suitable for:

Ah-xpc12rv