Cutting Tools - Makita DUR369N Instruction Manual

3. The cutting attachment continues to rotate for
a short period after turning the tool off. Don't
rush to contact the cutting attachment.
4. During operation, use the shoulder harness if
supplied with the tool. Keep the tool on your
right side firmly.
5. Do not overreach. Keep proper footing and
balance at all times. Watch for hidden obsta-
cles such as tree stumps, roots and ditches to
avoid stumbling.
6. Always be sure of your footing on slopes.
7. Walk, never run.
Never work on a ladder or tree to avoid loss of
8.
control.
9. If the tool gets heavy impact or fall, check the
condition before continuing work. Check the
controls and safety devices for malfunction. If
there is any damage or doubt, ask our autho-
rized service center for the inspection and
repair.
10. Do not touch the gear case during and imme-
diately after the operation. The gear case
becomes hot during operation and can cause burn
injury.
11. Take a rest to prevent loss of control caused
by fatigue. We recommend taking a 10 to 20-min-
ute rest every hour.
12. When you leave the tool, even if it is a short
time, always remove the battery cartridge. The
unattended tool with the battery cartridge installed
may be used by unauthorized person and cause
serious accident.
13. If grass or branches get caught between the
cutting attachment and guard, always turn the
tool off and remove the battery cartridge before
cleaning. Otherwise the cutting attachment may
rotate unintentionally and cause serious injury.
14. Never touch moving hazardous parts before
the moving hazardous parts have come to
a complete stop and the battery cartridge is
removed.
15. If the cutting attachment hits stones or other
hard objects, immediately turn the tool off.
Then remove the battery cartridge and inspect
the cutting attachment.
16. Check the cutting attachment frequently
during operation for cracks or damages.
Before the inspection, remove the battery
cartridge and wait until the cutting attachment
stops completely. Replace damaged cutting
attachment immediately, even if it has only
superficial cracks.
17. Never cut above waist height.
18. Before starting the cutting operation, wait until
the cutting attachment reaches a constant
speed after turning the tool on.
19. When using a cutting tool, swing the tool
evenly in half-circle from right to left, like
using a scythe.
20. Hold the tool by insulated gripping surfaces
only, because the cutting tool may contact
hidden wiring. Cutting tool contacting a "live" wire
may make exposed metal parts of the tool "live"
and could give the operator an electric shock.
21. Do not start the tool when the cutting tool is
tangled with cut grass.
22. Before starting the tool, be sure that the cut-
ting tool is not touching the ground and other
obstacles such as a tree.
23. During operation always hold the tool with both
hands. Never hold the tool with one hand during use.
24. Do not operate the tool in bad weather or if
there is a risk of lightning.

Cutting tools

1. Do not use a cutting tool which is not recom-
mended by us.
Use an applicable cutting attachment for the
2.
job in hand.
— Nylon cutting heads (string trimmer heads)
and plastic blades are suitable for trimming
lawn grass.
— Never use other blades including metal
multi-piece pivoting chains and flail blades. It
may result in serious injury.
3. Only use the cutting tool that are marked with
a speed equal or higher than the speed marked
on the tool.
4. Always keep your hands, face, and clothes
away from the cutting tool when it is rotating.
Failure to do so may cause personal injury.
5. Always use the cutting attachment guard prop-
erly suited for the cutting attachment used.
Vibration
1. People with poor circulation who are exposed
to excessive vibration may experience injury
to blood vessels or the nervous system.
Vibration may cause the following symptoms
to occur in the fingers, hands or wrists: "Falling
asleep" (numbness), tingling, pain, stabbing sen-
sation, alteration of skin color or of the skin. If any
of these symptoms occur, see a physician!
2. To reduce the risk of "white finger disease",
keep your hands warm during operation and
well maintain the tool and accessories.
Transport
1. Before transporting the tool, turn it off and
remove the battery cartridge.
2. When transporting the tool, carry it in a hori-
zontal position by holding the shaft.
3. When transporting the tool in a vehicle, prop-
erly secure it to avoid turnover. Otherwise
damage to the tool and other baggage may result.
Maintenance
1. Have your tool serviced by our authorized
service center, always using only genuine
replacement parts. Incorrect repair and poor
maintenance can shorten the life of the tool and
increase the risk of accidents.
2. Before doing any maintenance or repair work
or cleaning the tool, always turn it off and
remove the battery cartridge.
3. Always wear protective gloves when handling
the cutting tool.
12 ENGLISH