1. Manuals
  2. Brands
  3. Lincoln Electric Manuals
  4. Cutter
  5. Growth Series
  6. Assembly manual

Lincoln Electric Growth Series Assembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

GROWTH SERIES
GROWTH SERIES
GROWTH SERIES
GROWTH SERIES
Torchmate 2X4 Growth Series
with
ACCUMOVE™2
™
™
Assembly Guide
May 14, 2015
Copyright 2012–2015 by Torchmate, Inc.
TMS-011-0204-02
Technology

Advertisement

Table of Contents
loading

Related Manuals for Lincoln Electric Growth Series

Summary of Contents for Lincoln Electric Growth Series

  • Page 1 TMS-011-0204-02 GROWTH SERIES GROWTH SERIES GROWTH SERIES GROWTH SERIES ™ ™ Torchmate 2X4 Growth Series with ACCUMOVE™2 Technology Assembly Guide May 14, 2015 Copyright 2012–2015 by Torchmate, Inc.
  • Page 2 1170 Trademark Drive, #101 Reno, NV 89521 www.torchmate.com Copyright © 2011-2015 by Lincoln Electric Cutting Systems All rights reserved. Reproduction of this work, in whole or in part, without written permission of the publisher is prohibited. The publisher does not assume and hereby disclaims any liability to any party for any loss or damage caused by any error or omission in this manual, whether such error results from negligence, accident, or any other cause.
  • Page 3 GROWTH SERIES GROWTH SERIES ™ 2X4 Growth Series CNC Cutting Table pictured with optional water table and plasma torch Assembly Guide...

  • Page 4: Table Of Contents

    Step B10: Test jog gantry at high speed ..... . . 44 Typical additional wiring steps......45 Torchmate Growth Series...
  • Page 5 Maintenance and Parts........79 Growth Series care and maintenance ..... . 80 Recommended 2X4 spare and replacement parts .

  • Page 6: Statement Of Warranty

    Statement of Warranty Lincoln Electric Cutting Systems equipment is designed and built with quality in mind. However, your overall satisfaction with our products generally can be increased by proper installation ... and thoughtful operation on your part. 30 Day guarantee...
  • Page 7 Any claim by Buyer with reference to the Goods sold hereunder shall be deemed waived by the Buyer unless submitted in writing to seller within the earlier of (i) thirty (30) days following the date Buyer discovered or by reasonable inspection should have discovered, any claimed breach of foregoing warranty, or (ii) 12 months following the date of shipment.

  • Page 8: Welcome To Torchmate

    Call, Call, Call! We are here for you! Thank you again for putting your trust in us. We will do our best to not let you down. Sincerely, The Torchmate Technical Support Team Lincoln Electric Cutting Systems Torchmate Growth Series viii...

  • Page 9: Torchmate Company History

    Growth Series: the expandable Torchmate 2x2, 2x4, and 4x4 CNC Systems. In 2011, the Kunz’ family vision was realized when Lincoln Electric, a stalwart welding ma- chine company from Cleveland, Ohio, acquired Torchmate. To bring world-class metal cutting equipment to its customers world-wide, Torchmate will continue to create, sell, and support products in Reno, NV.

  • Page 10: Technical Support

    Torchmate Technical support is available Monday through Friday from 6 AM to 4 PM (06:00 to 16:00) Pacific Time Zone. Toll Free: 1-866-571-1066 International: 775-673-2200 Fax: 775-673-2206 Email: support@torchmate.com Call us for Consumables, or visit our web store www.TorchmateStore.com Torchmate Growth Series...

  • Page 11: Safety Information

    Safety Information Assembly Guide...

  • Page 12: Safety First

    Safety First Lincoln Electric Cutting Systems equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thoughtful operation on your part. WARNING DO NOT INSTALL, OPERATE, OR REPAIR THIS EQUIPMENT...
  • Page 13 Arc rays ARC RAYS can burn. Plasma Arc Rays can injure your eyes and burn your skin. The plasma arc process produces very bright ultraviolet and infrared rays. These will damage your eyes and burn your skin if you are not properly protected. Use safety glasses and a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when performing or observing plasma arc cutting or gouging.
  • Page 14 Fire and explosion can be caused by hot slag, sparks, oxygen fueled cutting flame, or the plasma arc. Have a fire extinguisher readily available. Provide a fire watch when working in an area where fire hazards may exist. Torchmate Growth Series...
  • Page 15 When not cutting or gouging, make certain no part of the electrode circuit is touching the work or ground. Accidental contact can cause overheating and create a fire hazard. Be sure there are no combustible or flammable materials in the workplace. Any material that cannot be removed must be protected.
  • Page 16 Never coil the torch cable around your body. 8.4.3 Do not place your body between the torch and work cables. If the torch cable is on your right side, the work cable should also be on your right side. Torchmate Growth Series...
  • Page 17 8.4.4 Connect the work cable to the workpiece as close as possible to the area being cut or gouged. 8.4.5 Do not work next to cutting power source. Automatic AUTOMATIC OPERATION operation Any CNC machine may begin to operate automatically without warning. Only a trained individual familiar with the software, machine, and computer system should operate this equipment.
  • Page 18 17.2 Hot sparks, flying debris, other objects, or vehicles can melt, burn, or puncture these lines. Check them for punctures, burns, or other damage or defects that could cause failure. 17.3 Check the routing of the lines to keep them away from traffic and from underfoot. Torchmate Growth Series...
  • Page 19 Other Important Refer to the following standards or their latest revisions for more information: Pubications • OSHA, SAFETY AND HEALTH STANDARDS, 29CFR 1910, obtainable from the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402 • ANSI Standard Z49.1, SAFETY IN WELDING AND CUTTING, obtainable from the American Welding Society, 550 N.W.
  • Page 20 Torchmate technical support is available Monday through Friday, from 6 AM to 4 PM (06:00 to 16:00), Pacific Time Zone. Toll Free: 1-866-571-1066 International: 775-673-2200 Fax: 775-673-2206 Email: support@torchmate.com Call us for Consumables, www.TorchmateStore.com or visit our web store Torchmate Growth Series...

  • Page 21: Receiving And Preparation

    Receiving and Preparation Assembly Guide...

  • Page 22: Preparations Before Assembly

    Always consult with your electrical service provider or a qualified electrician regarding electrical code requirements in your local area for grounding rods and other measures you can take to reduce EMI. For additional information, see: http:/ /www.torchmatesupport.com/help/EMI Reduction.zip Torchmate Growth Series...
  • Page 23 • Recognize that smoke and dust are created by the cutting processes. Plan to remove it and Fumes to provide a supply of clean air. The Lincoln Electric Modular Extraction Hood removes dust and smoke. The Lincoln Electric...

  • Page 24: Receiving Your Shipment

    Receiving your shipment Your Torchmate 2X4 Growth Series CNC Cutting System will arrive in a shipping crate. If you ordered the optional water table, you will receive two crates. Please take the time to check your shipment as soon as it arrives.

  • Page 25: Parts Checklist

    Parts checklist On the next few pages, the parts included in your Torchmate 2X4 Growth Series CNC Cutting System ship- ment are listed in the order you assemble them. To make it easier to complete the assembly of your cutting system, you can lay out the received parts in this order as you check them against this list.
  • Page 26 Cable, motor, XLR / Molex, 25 ft TMS-402-0010-01 USB flash drive: VMD software and TMS-100-1000-01 owners manuals. 99R6 ball bearings TMS-432-0010-01 Screw, BSCS, ⁄ "–16 X 1 TMS-410-0218-16 Nut, Nylock, ⁄ "–16 steel, zinc-plated TMS-414-0201-18 Washer, flat, ⁄ ", steel, cadmium- TMS-413-0406-18 plated Torchmate Growth Series...
  • Page 27 Parts for the C-steps (optional)  Qty. Part Description Part Number Step GS water table side—long with cutout TMS-180-0001-05 GS water table side backplate—long TMS-180-0001-06 Screw, BSCS, 10–32 X ⁄ " TMS-410-0511-08 Nut, Nylock, 10–32, steel, zinc plated TMS-414-0201-11 GS water table leg—corner leg TMS-180-0001-28 GS water table leg—side leg TMS-180-0001-29...
  • Page 28 Height Control Lifter, Accumove2 TMS-101-1100-02 Screw, SCS, ⁄ ”-18 X 1.0” lg, hex drive TMS-410-0016-16 Plasma cutter power supply unit Purchased separately CNC Interface cable Supplied with plasma cutter Height Control VFC TMS-101-1100-01 Arc Voltage/Ohmic Cable TMS-101-1109-01 Torchmate Growth Series...
  • Page 29 Raw arc voltage cable Depends on plasma (included with CNC Interface cable for power unit Lincoln Electric plasma power units) Quick connect crimp terminal (female) From your toolbox Terminal Block Plug 2Pos Str 5.08mm TMS-403-0076-01 Input Cable, Accumove, Torchmate Pro...

  • Page 30: Step-By-Step Setup

    D steps—Deploy the selected tooling. The steps here vary by tool type: • Mount the tool • Run the cable(s), gas lines, etc. • Set up the tool in the VMD software The C steps for the water table are optional Torchmate Growth Series...
  • Page 31 List parts and • On previous pages you were provided a parts list, organized to help you receive parts. The location, in terms of the numbered steps that follow, were also listed so you can quickly components locate the step that uses a particular part. •...
  • Page 32 Torchmate Technical Support is available Monday through Friday from 6 AM to 4 PM (06:00 to 16:00), Pacific Time Zone. Toll Free: 1-866-571-1066 International: 775-673-2200 Fax: 775-673-2206 Email: support@torchmate.com Call us for Consumables, or visit our web store www.TorchmateStore.com Torchmate Growth Series...

  • Page 33: Assembling The Cutting Table

    Assembling the cutting table Assembly Guide...

  • Page 34: Assembly Overview

    Assembly overview In the following steps, you will assemble the Torchmate 2X4 Growth Series CNC Cutting System table. It pre- cisely controls the motion of the torch or other tools. Seven steps are required for Assembly. Additional steps will be used to bind the controller to the table and complete the adjustment for level and square. If you pur- chased the optional water table, you will find the instructions for assembling the water table and mounting the cutting table on it following this section.
  • Page 35 125 lbs Weight of • The completed CNC cutting table is sturdy and heavy-duty, so that it can precisely and accurately move the torch, support your completed CNC 57 kg material, and support the weight of the water in the water table cutting table reservoir.

  • Page 36: Step A1: Prepare Table Sides

    Step A1: Prepare table sides The sides of your Torchmate 2x4 Growth Series CNC Cutting System are pre-assembled with a drive-screw, motor, and steel rails. The cross-members are extruded aluminum channels which are held to the sides with T-nuts. Here you will prepare sides by adding the T-nuts. In the next step you will add the cross-members.

  • Page 37: Step A2: Assemble Table Frame

    Step A2: Assemble table frame The Torchmate 2x4 Growth Series CNC Cutting System table uses extruded aluminum cross-members attached to the sides with T-nuts. Here you will create the initial linking of the sides with the cross-members. The final adjustment for squareness is completed at a later step.

  • Page 38: Step A3: Install The Gantry

    Step A3: Install the gantry Like the sides of the Torchmate 2x4 Growth Series CNC Cutting System table, the full gantry is pre-assembled with a drive-screw, motor, and steel rail. In this step, you will set the gantry on the side rails.

  • Page 39: Step A4: Check / Adjust Vertical Bearings

    Step A4: Check / adjust vertical bearings The smooth motion of the Torchmate 2x4 Growth Series CNC Cutting System gantry is managed by the four vertical bearings that carry the gantry’s weight. In this step you check the gantry’s clearance above the side rails and adjust its height, if necessary, by moving the vertical bearings.

  • Page 40: Step A5: Adjust The First Cross-Member

    Step A5: Adjust the first cross-member With the gantry positioned on your Torchmate 2x4 Growth Series CNC Cutting System table, you can now begin to adjust the table’s squareness and begin to tighten the cross-members. Squaring is essential for smooth and accurate gantry operation.

  • Page 41: Step A6: Adjust The Second Cross-Member

    Step A6: Adjust the second cross-member With the gantry secured to your Torchmate 2x4 Growth Series CNC Cutting System table, you can now ad- just the table’s squareness and securely tighten the cross-members. When squared, the gantry will operate smoothly and accurately.

  • Page 42: Step A7: Link The Gantry To The Drive Screws

    Step A7: Link the gantry to the drive screws Your Torchmate 2x4 Growth Series CNC Cutting System achieves accuracy and precision in cutting complex shapes because it uses anti-backlash nuts, which minimize backlash (play) on its drive screws. Here you will attach the gantry to the side rail drive screw brackets.

  • Page 43: Binding The Accumove ™ 2

    Binding the Accumove ™ Assembly Guide...

  • Page 44: Overview Of Wiring

    Overview of wiring For adjusting the 2x4 Growth Series CNC Cutting System table, you only need a minimal setup for the Torch- mate Accumove2. Establish communications between the controller and the computer, load the software, and run the X and Y motor cables from the table to the controller. Later, you will see how to connect a typical plasma cutter and other tools.

  • Page 45: Step B1: Run Crossover Ethernet Cable

    Step B1: Run crossover Ethernet cable Using an Ethernet cable connection, the Torchmate Accumove2 receives commands from the VMD (CAM) software that runs on the laptop (or PC) . To make it easy to begin operations, an Ethernet crossover cable (red) is provided that requires no other network devices to establish communication.

  • Page 46: Step B2: Run Motor Cables

    This will cause irreversible damage to the Accumove2. Connect motor cables in the indicated order: 1 green Motor Cables = gantry 2 yellow = rail 3 purple Ethernet = Z-axis / AVHC Crossover Cable 4 white = rail Torchmate Growth Series...

  • Page 47: Step B3: Install The Vmd Software

    Step B3: Install the VMD software The VMD software controls the table. The laptop (or desktop) computer that runs Torchmate VMD software sends commands to the Accumove2, which then sends signals to the table’s motors and also (typically) to the plasma cutter to fire the torch. The software must be installed on the computer from the USB flash drive. Required parts / Part Description...

  • Page 48: Step B4: Set The Ip Address

    Tab key to fill in the Subnet mask. Click OK to save. • Power on the Accumove2, then start the VMD software. Installation screens Select Use the following IP address Disable all connections except the Accumove2. To check, unplug/replug the red cable Torchmate Growth Series...

  • Page 49: Step B5: Set The Initial Datum And Log On To Vmd

    Step B5: Set the initial datum and log on to VMD So that the VMD can begin communicating position information with the Accumove2, the first requirement is to set the initial location as the machine's temporary datum. This will be reset to the actual machine datum after the configuration file is loaded.

  • Page 50: Step B6: Load Configuration File For Table

    Illustrations Click the Load Configuration button Click on the file name to highlight it, then click OK Torchmate Growth Series...

  • Page 51: Step B7: Setting And Resetting The Table's Datum

    Step B7: Setting and resetting the table's datum The Accumove2 calculates all position offsets and speeds by referring to a 3-axis zero point. This point is referred to as the table’s “datum.” Without its datum, your table cannot operate, so it must be set whenever the Accumove2 is powered on.

  • Page 52: Step B8: Jog Gantry To Set Side Bearings

    Illustration Use the Y-axis arrow keys to jog the gantry to each end of the table If the gantry binds, contact TECHNICAL SUPPORT Torchmate Toll Free: 1-866-571-1066 Technical Support International: 775-673-2200 Fax: 775-673-2206 support@torchmate.com Email: Torchmate Growth Series...

  • Page 53: Step B9: Add Underside Bearings (Optional)

    Step B9: Add underside bearings (optional) If a routing tool is mounted on the Torchmate 2x4 Growth Series CNC Cutting System table, you can help prevent the gantry from being lifted from the rails during routing by installing underside roller bearings. The top and side bearings are pre-installed on the gantry, but you must add the underside bearings for routing configurations.

  • Page 54: Step B10: Test Jog Gantry At High Speed

    Step B10: Test jog gantry at high speed The Torchmate 2X4 Growth Series CNC Cutting System table should now be ready for operation. This step tests for any binding or problems with moving the gantry at fully adjusted operational speeds.

  • Page 55: Typical Additional Wiring Steps

    Typical additional wiring steps The Torchmate 2X4 Growth Series CNC Cutting System table is most frequently used with a plasma cutter. This general discussion describes the additional connections that prepare the table for plasma cutting. Required parts / Part Description...
  • Page 56 Torchmate Growth Series...

  • Page 57: Coupling The Water Table (Optional)

    Coupling the water table (optional) Assembly Guide...

  • Page 58: Assemble The (Optional) 2X4 Water Table

    (208V or 230V / 1 or 3 phase / 50 or 60 Hz), power for the computer and CNC controller (120 V), access to compressed air (and/or recommended gas), and how to obtain (and drain) the water. Torchmate Growth Series...
  • Page 59 155 lbs • The completed water table is sturdy and heavy-duty, so that it Weight of can safely support the material you cut. completed 71 kg water table • With the cutting table installed, the table is even heavier: close to 280 lbs (127 kg).

  • Page 60: Step C1: Assemble The Two End Panels

    Attach the Side Panel Back Plate to the ‘Torchmate’ Cut Side using six #10–32 Button Instructions • Head Cap Screws and six #10–32 Hex Nuts. • Repeat this assembly for both cut sides. • Fully tighten the nuts to the screws. Illustration Torchmate Growth Series...

  • Page 61: Step C2: Add A Leveling Foot To Each Leg

    Step C2: Add a leveling foot to each leg The second step in water table assembly is to attach a leveling foot to each of the four legs. The leveling feet are used to level the table when the floor is uneven. Each leg will be adjusted individually before filing the table with water.

  • Page 62: Step C3: Attach Legs To Each End Panel

    "–18 Hex Nuts • The side panels are slotted to be adjusted once the cutting table is attached. • Repeat this assembly for the second cut out side. • Do not fully tighten the cap screws. Illustration Torchmate Growth Series...

  • Page 63: Step C4: Connect The Side Legs And Side Panels

    Step C4: Connect the side legs and side panels In the fourth step, you will attach the side legs and panels to the corner legs and end panel assemblies. Be- cause adjustments may be required, you’ll only partly tighten the screws. Required parts / Part Description...

  • Page 64: Step C5: Insert Cross-Member Into Frame

    Do not fully tighten the cap screws at this time. Illustrations This overhead view of the water table 's The cross-member is retained by the legs and sides shows where to add the welded support channels in the side cross-member. legs. Torchmate Growth Series...

  • Page 65: Step C6: Seal The Edge To The Water Pan Bed

    Step C6: Seal the edge to the water pan bed The 2x4 Growth Series water pan bed, which holds the water, is built in multiple pieces so that during “growth” to the larger sized water tables, the existing pans can continue to be used. The sixth step attaches the pans and edge as well as seals the water pans.

  • Page 66: Step C7: Install The Drain Valve And Pan

    • You may connect a hose or other plumbing to the drain valve so that you may dispose of the table’s water appropriately, as necessary. Illustration Install the drain valve and lower the pan into the frame Torchmate Growth Series...

  • Page 67: Step C8: Add The Material Support Slats

    Step C8: Add the material support slats The 2x4 water table provides a heavy-duty support system for the material being cut using slats that you supply (and replace from time to time) from local material. Placed on edge, with a slight curvature, the slats de- velop the strength required to provide durable, long lasting service.

  • Page 68: Step C8: Secure Cutting Table To Water Table

    A5 of the cutting table installation for the beginning steps of the squaring procedure. • With the table square and level, fully tighten all screws. • Fill the water pan with water and check for leaks. Illustration Torchmate Growth Series...

  • Page 69: Deploying The Plasma Cutter

    Deploying the Plasma Cutter Assembly Guide...

  • Page 70: Cutting Tools For Growth Series ™ Tables

    Approximately 95% of Growth Series customers use their equipment for cutting metal plate Intelligent AVHC and this number seems to be growing. With this in mind, the Growth Series CNC tables with for plasma Accumove2 Technology come with an advanced system for achieving high quality cutting, with intelligent Arc Voltage Height Control.
  • Page 71 • With special optional mounting adapters, a router z-axis and Router Z-axis motor may be installed upon your Growth Series CNC table to enable three-dimensional routing of wood, plastic, and foam, and the light-duty machining of metals and composites. •...

  • Page 72: Features Of The Accumove2 Avhc

    Features of the Accumove2 AVHC The Growth Series tables with Accumove2 Technology includes an intelligent AVHC system to produce cuts with a high quality level. Other than good quality consumables, the primary factor governing cut quality is the length of the plasma arc. Standard arc lengths are published for each plasma cutter and the AVHC system uses the arc voltage measuring technique to control the height of the torch above the material being cut.
  • Page 73 For more information on what you can do to reduce EMI effects and ensure the highest cut quality for your Growth Series with Accumove2 Technology CNC system, please find the file EMI Reduction.pdf on the Torchmate / Lincoln Electric Cutting Systems USB Flash Drive supplied with your system, or download it from this web location: http:/ /www.torchmatesupport.com/help/EMI Reduction.zip...

  • Page 74: Step D1: Attach The Tool Mounting Bracket To The Tool Mounting Pate

    Insert the screws through the front of the lifter station, then through the mounting plate. The nuts will be behind the mounting plate. • Tighten the nuts securely. • Re-mount the tool mounting plate (with the bracket) to the gantry. Torchmate 2x2 Growth Series...
  • Page 75 Remove the four bolts Illustration to remove the tool mounting plate from the gantry Bolt the bracket to the plate with the bolts and locknuts. Then re-mount the plate on the gantry. Optional direct • Use of the tool mounting bracket is only required if the full 24” of travel is required on the use of the tool Y-axis.

  • Page 76: Step D2: Mount The Avhc Lifter

    Step D2: Mount the AVHC lifter Mount the Arc Voltage Height Control (AVHC) machine torch lifter station to the tool-mounting bracket (or directly to the tool mounting plate) on the Growth Series gantry using the included hardware. Required parts /...
  • Page 77 Illustration There are six threaded mounting holes in a rectangular array on the back of the Z-axis lifter. Use the four holes that are closest to the end of the Z-axis lifter to mount it to the tool mounting bracket or tool mounting plate. Connect the •...

  • Page 78: Step D3: Prepare The Plasma Cutter

    CNC system, and respond to signals when the CNC system tells it to start and stop cutting. All these signals go through the CNC interface cable on Lincoln Electric plasma cutters. Other plasma cutters must use additional wiring. These cables must be prepared for connection to the Accumove2 and VFC. Other...
  • Page 79 For other plasma power units, the raw arc voltage signal is frequently not available on the CNC cable. • If you purchased one of these units with your Torchmate Growth Series CNC System, the factory will have installed the necessary raw arc voltage cable before shipping. •...

  • Page 80: Step D4: Place The Vfc Unit

    EMI is an important consideration for producing high quality cutting with your CNC system. For more information on EMI, download the PDF document from this web location: http:/ /www.torchmatesupport.com/help/EMI Reduction.zip Mount the Accumove VFC securely Use the mounting holes Torchmate 2x2 Growth Series...
  • Page 81 • To reduce the length of the raw arc voltage wires, you can trim the entire CNC interface Trim the CNC cable so that it just reaches the Accumove VFC unit interface cable Locate the Accumove VFC near the plasma Shorter distance Longer distance power unit to trim...

  • Page 82: Step D5: Connect The Vfc Unit

    • Splice the red and black wires from the arc voltage cable to the arc voltage wires in the Lincoln Electric CNC interface cable (red [+]goes to G [+] and black [-] goes to D [-]. • If a non-Lincoln Electric plasma power unit was supplied with your CNC system, splice to the installed raw arc voltage cable.
  • Page 83 Splice and Splice the red and black wires connect the to the plasma power unit’s cables raw arc voltage wires. Be sure to observe polarity. Run the orange wire to the ohmic sensing cap using a quick connect crimp terminal Run the ground wire from the VFC to the Accumove2 ground...

  • Page 84: Step D6A: Wiring For Lincoln Electric Plasma Cutters

    Step D6a: Wiring for Lincoln Electric plasma cutters Wiring for Lincoln Electric plasma cutters is simplified because all connections to the plasma cutter are contained in the CNC cable. The additional wiring steps are based on the diagram on the following page.
  • Page 85 Use this wiring diagram for Lincoln Electric plasma cutters Assembly Guide...

  • Page 86: Step D6B: Wiring For Non-Lincoln Electric Plasma Cutters

    Step D6b: Wiring for non-Lincoln Electric plasma cutters Wiring for Lincoln Electric plasma cutters is simplified because all connections to the plasma cutter are con- tained in the CNC cable. The additional wiring steps are based on the diagram on the following page.
  • Page 87 Use this wiring di- agram for plasma cutters not made Lincoln Electric SPLICE SPLICE Assembly Guide...
  • Page 88 Torchmate 2x2 Growth Series...

  • Page 89: Maintenance And Parts

    Maintenance and Parts Assembly Guide...

  • Page 90: Growth Series Care And Maintenance

    Growth Series care and maintenance Although your Growth Series table may be brand new and shiny, it won’t stay that way for long unless you take care of it. But, more important than how it looks is how well it performs, yet the number one mainte- nance item that will keep your Growth Series machine running well is keeping it clean and free of rust.
  • Page 91 • A typical nylon scrubbing pad, moistened with some metal care lubricant can quickly Cleaning the rails remove light amounts of corrosion and dirt from the rails, and help to protect the rails which are in regular use. • Use the lubricant cleaner sparingly, but leave a light film on the rails to keep dust and moisture from accumulating on the rails.

  • Page 92: Recommended 2X4 Spare And Replacement Parts

    ⁄ ” shaft collar TMS-433-0012-01 99R6 ball bearings TMS-432-0010-01 Replacement torch mounting sleeve or depends on torch head. torch model Order spare parts • These can be easily ordered through the TorchmateStore.com website or by calling 866-571-1066. Torchmate Growth Series...

  • Page 93: Upgrade Parts For The Growth Series 2X4

    Upgrade parts for the Growth Series 2X4 When it’s time to grow your GS 2X4 to a 4X4 or to add a water table, use the following part number guide when you call our sales department. For this upgrade Order this part...
  • Page 94 Toll Free: 1-866-571-1066 International: 775-673-2200 Fax: 775-673-2206 Email: support@torchmate.com Torchmate Growth Series...

This manual is also suitable for:

Torchmate 2x4 growth accumove 2 series

Table of Contents