Sony CCP-8000 Operation Manual page 12

a REMOTE connector (BNC type)
Connect this connector with a BNC cable to an S-BUS data
link via a T bridge.
An S-BUS data link is a single signaling circuit (S-BUS)
to which multiple devices can be connected to exchange
data.
Connecting devices such as HDS-X3000 series routing
switchers and remote panels to an S-BUS data link enables
the following kinds of control.
• Returning to the S-BUS, tally data created by this unit on
the basis of data received from other devices
• Switching the cross-points of a routing switcher from the
center control panel
• Switching the cross-points of a switcher from the remote
panel
• Displaying on the center control panel source names set
on a routing switcher
b REF IN (reference signal input) connectors
(BNC type)
If you wish to synchronize this unit to an external reference
signal, input the reference signal. For an HDTV system,
input an HD tri-level sync signal, black burst signal, or
analog sync signal. For an SDTV system, input a black
burst signal or analog sync signal.
The two connectors have a loop-through configuration.
Signal input to one connector can be output from the other
connector. If you will not be using the loop-through
output, be sure to terminate the unused connector with the
supplied 75Ω terminator.
c EXT (extension) PANEL 1 to 3 connectors
(D-sub 50-pin, special interface)
Connect to the MKS-8075 Extension Adaptors and AUX
panels to install operation modules apart from the center
control panel.
d GPI (General Purpose Interface) connector
(D-sub 25-pin)
Connect to external devices for input and output of trigger
signals. Up to eight inputs and eight outputs are possible,
with input and output conditions set on the center control
panel.
e LTC IN (longitudinal timecode input) connector
Connect to a timecode generator.
The specifications of this connector vary as shown below
according to the type of the system control unit.
System Control Units
MKS-8010
MKS-8010A
f - AC IN (AC power input) A and B connectors
(3-pin)
Connect to 100 to 240 V AC power supply with the
optional AC power cords.
12
Location and Function of Parts
Connectors
D-sub 9-pin (RS-422A standard)
BNC Type
Depending on the configuration of your unit, the Backup
Power Supply Unit may not be installed. In that case, the
AC IN B connector is not used.
Caution
For information about installing, contact your Sony
service representative.
g U (signal ground) terminal
Connect to the system ground.
h EDITOR PANEL connector
The specifications of this connector vary as shown below
according to the type of the system control unit.
System Control Units Connectors
MKS-8010 D-sub 9-pin (RS-422A standard)
MKS-8010A D-sub 15-pin (RS-422A standard)
This connector is reserved for future system expansion.
i PERIPH (peripheral) connector (RJ-45)
Connect to the DCU-8000 Device Control Unit Pack with
a cross cable to enable communications with the DCU-
8000.
Note
An Ethernet switch is required to connect two or more
DCU-8000 Device Control Units.
j DEVICE connector (USB Type A)
Connect to the HOST connector of the main panel, AUX
panel or the MKS-8076 Memory Card/USB Adaptor.
k DATA connector (RJ-45)
Connect to an Ethernet switch.*
The MVS-8400/8300/8200 Switcher Processor Pack, the
MVE-8000 DME Processor Pack and other devices can be
connected in the same way to the Ethernet switch to form
a network for exchange of signals between the devices.
This network is used primarily for exchange of various
types of data (key frame effects, snapshots, etc.) and still
pictures of frame memory.
* Ethernet is a trademark of XEROX Corporation.
For information about Ethernet switches that can be used in an MVS
system, contact your Sony service representative.
For more information about Ethernet switch connectors,
see "MVS-8000 System Configuration" (page 17).
For detailed information about setting up the Ethernet
switch, refer to the documentation supplied with the
Ethernet switch.
l MAIN PANEL connector (D-sub 50-pin,
special interface)
Connect to the SCU connector of the main panel.