Subscribe to Our Youtube Channel
Related Manuals for REMKO KFB 4
Summary of Contents for REMKO KFB 4
- Page 1 Operating and installation instructions REMKO cabled remote controls for MVD, MVW and MXV unit series KFB 4 0230-2019-08 Edition 1, en_GB Read the instructions prior to performing any task!
- Page 2 Read these operating instructions carefully before commis- sioning / using this device! These instructions are an integral part of the system and must always be kept near or on the device. Subject to modifications; No liability accepted for errors or mis- prints! Translation of the original...
-
Page 3: Table Of Contents
Table of contents Safety and usage instructions......................4 1.1 General safety notes........................4 1.2 Identification of notes........................4 1.3 Personnel qualifications........................4 1.4 Dangers of failure to observe the safety notes................4 1.5 Safety-conscious working....................... 4 1.6 Safety notes for the operator......................5 1.7 Safety notes for installation, maintenance and inspection.............. -
Page 4: Safety And Usage Instructions
REMKO cabled remote controls Safety and usage instructions CAUTION! This combination of symbol and signal word 1.1 General safety notes warns of a potentially hazardous situation, which if not avoided may cause injury or mate- Carefully read the operating manual before com- rial and environmental damage. -
Page 5: Safety Notes For The Operator
The setup, connection and operation of the plete and return the "certificate of warranty" to units and its components must be undertaken REMKO GmbH & Co. KG at the time when the in accordance with the usage and operating units are purchased and commissioned. -
Page 6: Transport And Packaging
REMKO cabled remote controls 1.11 Transport and packaging The devices are supplied in a sturdy shipping con- tainer. Please check the equipment immediately upon delivery and note any damage or missing parts on the delivery and inform the shipper and your contractual partner. -
Page 7: Technical Data
Technical data 2.1 Unit data Series KFB 4 Cabled remote control for Operating mode MVD, MVW and MXV unit types °C / Operating range -5 to +43 / 40 to 90 r.H. °C / Temperature range for storage purposes -10 to +60 / 20 to 85 r.H. -
Page 8: Operation
REMKO cabled remote controls Operation “Function” key By pressing this key it is possible to switch It is operated by the touch fields on the lower area between the functions. Alternatively, it is possible of the remote control. Information and settings are to switch between the individual functions by shown on the display. - Page 9 Remote control display Digital display The digital display shows the set room target tem- perature on the main screen and is also used to display settings and setting values in the Service menu. Switch-on delay This text is displayed when the switch-on delay is set or activated.
- Page 10 REMKO cabled remote controls Switching the remote control on and off 2. Dehumidification mode: In Dehumidification mode, the setpoint tempera- ture and the fin position can be set. It is not pos- sible to set the fan speed. The fan is switched off at certain intervals to lower the fin temperature.
- Page 11 Adjusting the target temperature Adjusting the air outlet fins The positioning of the fins can be adjusted with the “Swing fin” key. Five angles and an automatic mode are available, in which the air outlet fin oscil- lates. In Automatic mode, the air outlet fin can be stopped at the current position by pressing the Swing fin key again.
- Page 12 REMKO cabled remote controls Activating and deactivating functions Energy saving function On the cabled remote control, certain functions are If the energy saving function is activated in cooling available to the user depending on the operating mode, the fan speed is set to automatic and the mode.
- Page 13 Para- Factory meter Function Setting setting Description Reserved Activates or deactivates Activated Enable heating function the enabling of the Deactivated heating function Reserved Deactivated Determines after how every 1250 hrs. many operating hours Filter cleaning reminder every 2500 hrs. the cabled remote con- time span trol displays a reminder every 5000 hrs.
- Page 14 REMKO cabled remote controls Para- Factory meter Function Setting setting Description Heating request is termi- nated when measured Control behaviour in temperature is ... °C heating mode higher than the setpoint value. same as DIP switch set- ting on indoor unit 0 °C...
- Page 15 Para- Factory meter Function Setting setting Description E-valve position in Determines E-valve stand-by mode or position in standby mode heating mode or heating mode. same as DIP switch set- ting on indoor unit Determines the unit in °C (Celsius) Temperature unit which temperatures are °F (Fahrenheit) to be displayed.
-
Page 16: Assembly Instructions For Qualified Personnel
REMKO cabled remote controls Assembly instructions Installation for qualified personnel Disconnect the power supply. Check the contents of the packaging for complete- Connect the 2-core cable to the terminals on ness and check the unit for visible transport the rear side as shown in the wiring diagram. -
Page 17: Electrical Wiring
Electrical wiring Electrical wiring diagram Fig. 13: Electrical wiring diagram 1: Indoor unit 2: Cabled remote control Commissioning Switch the unit on using the room tempera- ture controller. Check all functions. Install all removed parts. Familiarise the operator with the functions. -
Page 18: Index
REMKO cabled remote controls Index Assembly ......16 Recirculation mode ..... . . 8 Removing the housing cover . - Page 20 REMKO QUALITY WITH SYSTEMS Air-Conditioning | Heating | New Energies Telephone +49 (0) 5232 606-0 REMKO GmbH & Co. KG Hotline within Germany +49 (0) 5232 606-0 Klima- und Wärmetechnik Telefax +49 (0) 5232 606-260 Im Seelenkamp 12 E-mail info@remko.de...
Need help?
Do you have a question about the KFB 4 and is the answer not in the manual?
Questions and answers