Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ACTi Manuals
  4. Security Camera
  5. Q51
  6. Configuration manual

ACTi Q51 Configuration Manual

With ras
Hide thumbs Also See for Q51:

Advertisement

Quick Links

Download this manual
Q51 Configuration Guide
with RAS
2019/05/28

Advertisement

loading

Related Manuals for ACTi Q51

Summary of Contents for ACTi Q51

  • Page 1 Q51 Configuration Guide with RAS 2019/05/28...
  • Page 2 2. Find the Q51 camera you would like to install. 3. Open IE browser. (Please be sure to use IE browser.) 4. Enter the IP address of Q51 to connect by using IE browser. 5. Enter the account / password (admin/123456) and login to the web configurator of Q51.
  • Page 3 “eMap” and save it on the desktop. This step will be used in Part two “(Step 5) – Heat Map, Increase eMap Note: settings”. 7. Click on the tool icon to enter the settings page of Q51. www.acti.com...
  • Page 4 8.3 Click “Apply” to save. 9. Please set the network parameters according to the following figure. 9.1. Click “IP Setting” 9.2. Click “Connection Type” 9.3. Click “Static IP Address” 9.4. Configure the related IP parameters 9.5. Click “Apply” to save the settings. www.acti.com...
  • Page 5 - Server 1 :Please tick - Network Address: Please enter the IP address set by the installed Server (MGB Server) - Network Port: Please enter “8082” - Account: Please enter “admin” - Password: Please enter “123456” 10.5. Click “Apply” to save the settings. www.acti.com...
  • Page 6 CONFIGURATION GUIDE 11. Please set the Location parameters according to the following figure. 11.1. Click “Location” 11.2. IVS Server Name: Please fill in the store name, Ex: ACTi) Note: This will be used in Part two (Settings of adding device). Write down the name you have set on a piece of paper.)
  • Page 7 12.3 After entering the setting page, click “Setup” to start 12.4 Draw the analysis range as shown in the following figure, you can draw polygons to avoid the range that does not need to be detected, please try to avoid the light or screen. www.acti.com...
  • Page 8 12.6 Refer to the illustration and the following text to set 1. Check “Enabled” 2. Active on -> Tick all 3. Start Time: 00:00 4. End Time: 24:00 5. Reporting Server: All 12.7 Click “Apply” to save the settings. www.acti.com...
  • Page 9 CONFIGURATION GUIDE 13. Please set the HeatMap parameters according to the following figure. 13.1 Click “Intelligent video” 13.2 Click “Dwell time” on the setting page 13.3 After entering the setting page, click “Setup” to start. www.acti.com...
  • Page 10 13.5 Click “Setup”, then click “Get” to confirm the screenshot of the live environment. 13.6 Refer to the illustration and the following text to set 1.Check ”Enabled” 2.Active on -> Tick all 3.Start Time:00:00 4.End Time:24:00 5.Reporting Server:All 13.7 Click “Apply” to save the settings. www.acti.com...
  • Page 11 2. Sign in RAS (admin/123456) 3. Settings of adding device 3.1 Click “Overview”→ “Setting”→“MGB Server” 3.2 Click the same name as the one attached to the server. (Ex: MGB Server) 3.3 Click “Add new device” as the picture below www.acti.com...
  • Page 12 CONFIGURATION GUIDE 3.4 Choose “Q51” for the Device Type (Please refer to the picture below) www.acti.com...
  • Page 13 3.7 Be sure all the devices have been set properly, then click “Lock” . Click “Lock”→ “Save” （If there are still other devices that need to be added (except Q51), please click “Lock” after all the devices have been set without error.）...
  • Page 14 6. Enter Customer Number 7. Select “HeatMapDwell Device” same as the device we mentioned above. 8. Press “Save” 9. Click “Lock”, then press “Save” again for the settings （Please wait for the store to complete the related information, click “Lock” after confirmation.） www.acti.com...
  • Page 15 CONFIGURATION GUIDE Note: The saved settings cannot be changed after clicking “Lock”！ （If there is any setting error or there is a need to adjust, please contact ACTi customer service to unlock.） 4. Permission 1. Click “Setting” 2. Click “UserManagement”...
  • Page 16 2. Click “Add eMap” 3. Click “Upload eMap” 4. Click the camera icon to open the picture you saved in Part one 5. Click “Open file” 6. Click “Save” 7. Drag Q51 to the actual installation position as shown below www.acti.com...
  • Page 17 Copyright © 2019, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C. TEL : +886-2-2656-2588 FAX : +886-2-2656-2599 Email: sales@acti.com...