Advertisement
1
ORANGE BAG
STEP
• Place a piece of packaging under
the front of the unit to aid in assembly
of the front foot.
• Secure the front stabilizer tube to the
base frame plate with four socket
head bolts (M8x20L) and four arc
washers (8.2x18x1.5T). Tighten with
the 6mm L-shaped wrench.
2
BLUE BAG
STEP
• Take the right pedal arm and set the
roller wheel in the aluminum guide track.
Slide the opposite end of the pedal arm
into the U-shaped knuckle bracket.
Slide a socket head bolt (M10x55L)
with a washer (10x24.5x1T) through
the hole in the knuckle bracket and
pedal arm. Fix in place with a
washer (10x24.5x1T) and nylon nut
(M10). Tighten with the 8mm L-shaped
wrench and the 17mm wrench.
• Slide the pedal arm cover over the
TV Bracket
knuckle joint and fix in place with a bolt
Cables
(M5x12L). Tighten with the screwdriver.
• Repeat these steps on the left side.
Heart Rate
Wires
3
PINK BAG
STEP
• Slide the console mast boot onto
the console mast.
• Cut the zip ties holding the cables
and wires onto the console mast.
• Attach the mounting plate to the
bottom of the console mast with four
socket head bolts (M10x25L) and four
lock washers (M10). Tighten as much as
possible with the 8mm L-shaped wrench.
• Mount the console mast on the
frame by sliding the guide hole on the
mast mounting plate over the guide
screw on the front of the frame bracket.
Place a lock washer (M8) followed by
a flat washer (8x16x2T) on each of
the four remaining socket head bolts
(M8x25L). Insert the bolts to the rear
holes but do not completely tighten.
Next, insert the bolts to the front holes.
Tighten all four bolts as much as possible
with the 6mm L-shaped wrench.
• Wrap the wire tie that exits the hole
at the bottom front side of the console
mast around the data cable, coaxial
cable, and TV power cable coming
up from the frame. Pull the wire tie
and all cables up through the top of
the console mast.
• Remove the protective plastic
around the cables and data cable.
• Tuck the coaxial and TV power
cables into the console mast.
NOTE: If you have purchased the TV
bracket assembly, remove the screws
from the TV bracket cover located at
the front of the console mast, and
remove the cover. Feed the coaxial
and TV power cables through the hole
4
STEP
at the front of the console mast.
• Insert a zip tie through the hole in
the middle of the console plate and
loop it around the heart rate wires and
data cable. Pull to snug, but do not
over tighten.
2
STEP
Data Cable
Console Plate
Console Mast
Console Mast
Boot
3
STEP
Frame Bracket
Mounting Plate
End Cap
Pedal Arm
Link Arm
Knuckle Bracket
Plastic Wave
Washer
Plastic Wave
Washer
Flat Washer
Thin Metal
Wave Washer
4
GREEN BAG
STEP
• Remove protective covers from sleeves
of the pedal arms.
I M P O RTA N T: The washers in the
following step must be assembled in
the correct order.
• Slide one thin metal wave washer
1
STEP
(26x36x0.3T), one flat washer (25.5x38x1T),
and one plastic wave washer (26x36x2T)
onto the axle of the right link arm. Slide
the axle of the right link arm through the
sleeve on the right pedal arm. Secure
the link arm onto the pedal arm with the
plastic wave washer (26x36x2T), end
cap, and bolt (M8x12L). Tighten with
the 5mm L-shaped wrench.
• Repeat the step on the left side.
5
BLACK BAG
STEP
Front Stabilizer Tube
NOTE: With this next step it is helpful
to have a second person to hold the
dual-action arms in place while you
assemble them.
• Take the right dual-action arm and
Console
center the holes in the rotation housing
on the console mast. Secure with four
socket head bolts (M8x25L) and four
lock washers (M8). Tighten with the
6mm T-shaped wrench.
• Attach the dual-action arm rotation
6
STEP
cover to the dual-action arm center.
Secure in place with two bolts
(M5x15L). Tighten with the screwdriver.
• Slide a spacer onto each side of the
socket joint located on the end of the
link arm. Slide the bottom of the dual-
action arm bracket over the link arm
socket and spacers. From the outside
of the bracket, slide the bolt (M8x55L)
through the hole in the bracket and
socket joint. Secure with a washer
(8x16x1T) and nylon nut (M8).
Tighten with the 6mm T-shaped
wrench and 13mm wrench.
• Attach the inside dual-action arm
cover onto the bottom of the dual-
action arm with a bolt (M5x15L).
Insert the plastic connector to the
Accessor y Tray
inside dual-action arm cover. Slide the
outside dual-action arm cover onto the
other end of the plastic connector.
Secure the outside dual-action arm
Rotation
cover to the bottom of the dual-action
Housing
arm with a bolt (M5x15L). Tighten
both bolts with the screwdriver.
• Repeat these steps on the left side.
6
YELLOW BAG
STEP
• Slide the accessory tray onto the
console mast. Secure in place with
four panhead bolts (M8x20L). Tighten
with the 5mm L-shaped wrench.
• Remove the four bolts (M5x12L)
Dual-Action
from the back side of the console.
Arm
Connect the data cable and the heart
rate wires to the plugs in the back side
of the console. Place the console on
the mast and secure in place with the
bolts (M5x12L).
5
STEP
• Place the X6850HRT in its intended
location and plug in the power cord
to the electrical outlet.
Advertisement
