Table of Contents
Advertisement
SECTION 1
ductor with Amphenol to Amphenol plugs; order one of the
following:
6-foot. 19-cond., P/N 30686.
30-foot, 19-cond., P/N 30780.
60-foot, 19-cond., P/N 30781.
C. Welding Torch
Mig welding torches, with contact tip, wire conduit and
outlet guide for wire size/type to be employed, will be
required. Suitable air (MT-400) or water-cooled (MT-
450W, ST-16) torches may be used with the Digimig.
When using a water-cooled torch it will be necessary to
connect the torches water hose to either a continuous
water supply or to the wire feeder base by using an
optional water kit (see Section 1.5).
D. Gas Regulation
Shielding gas regulator/flowmeter and fitted hose to bring
gas from flowmeter to wire feeder. Such as:
Wire Type/
Size In. (mm)
Soft
.030 (.8)
.035 (.9)
3/64 (1.2)
1/16 (1.6)
Hard
.023 (.6)
.030 (.8)
.035 (.9)
.045 (1.2)
.052 (1.4)
1/16 (1.6)
Cored
.035 (.9)
.045 (1.2)
.052 (1.4)
.063, 1/16 (1.6)
5/64 (2.0)
U=U-groove, V=V-groove, Serr. = serrated
**
Requires outlet guide insert as follows: For .030, .035 wire use 993902, For 3/64 wire use 05N57, For 1/16 wire use 12N75, For 3/32 wire
use 05N58.
†
Recommended U-Groove Pressure Roll 2075346 be used.
†† Recommended U-Groove Pressure Roll 2075348 be used
(a) Includes replaceable sleeve (995651).
(b) Includes replaceable sleeve (995692).
(c) Requires guide bushing (17997).
(d) Requires replaceable sleeve (995693)
Table 1 - Digimig Feed Rolls
Two Roll Drive
Feed Roll
2075304 (U)
2075304 (U)
2075301 (U)
†
2075298 (U)
††
17998 (V)
2075300 (V)
2075303 (V)
2075302 (V)
2075330 (V)
2075299 (V)
19761 (Serr.)
19761 (Serr.)
2075261 (Serr.)
2075261 (Serr.)
2075261 (Serr.)
Regulator/Flowmeters:
R-5007 Argon/Helium/Nitrogen, P/N 998124.
R-5008 C0
, P/N 998125.
2
Gas Hoses:
Standard Duty, 40V77 (12-1/2-ft.) or P/N 34V38 (25-ft.)
Heavy Duty, P/N 19416 (12-1/2-ft.)
Must be used for C0
E. Feed Rolls
The Digimig comes equipped with a pressure roll but NOT
a feed roll. Select the proper feed roll and outlet guide from
Table 1 for the wire size and type to be used. To convert
the 2-Roll to 4-Roll Drive, order optional 4-roll Drive
Accessory Support, P/N 600216 and the appropriate kit
listed in Table 1.
F. Water Cooling
Water supply with fitted hose assemblies are required to
bring cooling water from supply to wire feeder, order
Water Hose 12-1/2-ft. P/N 40V76 as shown in Fig. 2-1.
Four Roll Drive
Feed Roll Kit*
999320
999321 (U)
999322 (U)
999322 (U)
—
999325 (V)
999326 (V)
999327 (V)
999328 (V)
999329 (V)
—
999330 (Serr.)
999331 (Serr.)
999332 (Serr.)
999333 (Serr.)
DESCRIPTION
or P/N 19415 (25-ft.).
.
2
Outlet
Guide
29N13**
29N13**
29N13**
29N13**
999745 (c)
993860 (a)
993860 (a)
39N15 (b)
39N15 (b)
39N15 (b)
993860 (a)
39N15 (b)
39N15 (b)
39N15 (b)
62N17 (d)
7
Advertisement
Table of Contents
