Vinotemp VINO1500CD Use And Care Manual
Wine-mate cooling unit
Hide thumbs
Also See for VINO1500CD:
- Installation instruction (2 pages) ,
- Use & care manual (20 pages) ,
- Use & care manual (21 pages)
Table of Contents
Advertisement
Quick Links
WINE-MATE Cooling Unit
Use & Care Manual
VINO1500CD, CTED
VINO2500CD, CTED
V
i
n
o
t
e
m
p
I
n
t
e
V
i
n
o
t
e
m
p
I
n
t
w
w
w
.
v
i
n
w
w
w
.
v
i
n
w
w
w
.
w
i
n
w
w
w
.
w
i
n
r
n
a
t
i
o
n
a
l
C
o
e
r
n
a
t
i
o
n
a
l
C
o
o
t
e
m
p
.
c
o
m
o
t
e
m
p
.
c
o
m
e
m
a
t
e
.
c
o
m
e
m
a
t
e
.
c
o
m
r
p
.
r
p
.
Advertisement
Table of Contents
Related Manuals for Vinotemp VINO1500CD
Summary of Contents for Vinotemp VINO1500CD
- Page 1 WINE-MATE Cooling Unit Use & Care Manual VINO1500CD, CTED VINO2500CD, CTED...
-
Page 2: Important Safety Information
Important Safety Information • DO NOT PLUG IN UNTIL 24 HOURS AFTER DELIVERY. • DO NOT USE A GROUND FAULT INTERRUPTER (GFI). • A DEDICATED 20 AMP CIRCUIT IS REQUIRED. - 1 -... -
Page 3: Table Of Contents
TABLE OF CONTENTS Features & Specifications…………….………….…………..3 Installation Instruction………………………………………..5 Temperature Control & Humidity Adjustment………….9 Care Guide……………………………………………………12 Troubleshooting……………………………………………..13 Wiring Diagram……………………………………….………16 Customer Support……………………………………………17 Warranty……………………………………………………….18 - 2 -... -
Page 4: Features & Specifications
Features and Specifications • VINO1500CD, CTED and VINO2500CD, CTED cooling units are designed and used to provide a subtle temperature between 50~65 space at a normal environment. • The refrigerated space will maintain humidity of 50~70% RH even when the environment becomes dry and humid. - Page 5 Fig. 1.2 DIMENSIONS (in) The dimension and capacity are specified as follows: Model Exhaust 1500cd Rear Exhaust 1500cted Top Exhaust 2500cd Rear Exhaust 2500cted Top Exhaust NOTES: • See the voltage, frequency and current specified on the label at the cooling unit.
-
Page 6: Installation Instruction
Installation Instruction NOTES: 1) DO NOT INSTALL ANY DUCTS ONTO THE SUPPLY, INTAKE AND EXHAUST. 2) MOUNTING BRACKETS, SCREWS, GASKETS AND OTHER SEAL MATERIALS ARE NOT INCLUDED. 3) THERE IS A GROMMET ON THE POWER CORD. PRESS AND FIT THE GROMMET INTO THE HOLE AT THE BOTTOM OF THE COOLING UNIT TO SEAL THE EXHAUST AIR NOT GOING TO THE CABINET. - Page 7 • Cut a rectangular inside opening at the rear of the cabinet with the 1/4” clearance inwards to the width and height of the cooling unit. By not going through, leave 1/2” lip inside at the wall to place the gaskets (see Fig. 2.2). •...
- Page 8 Fig. 2.2 MOUNTING CUTOUT & GASKET LIPS Fig. 2.3 TOP EXHAUST GASKET - 7 -...
- Page 9 2. Electrical Cord • We strongly recommend against the use of an extension cord. However, if you still select to use an extension cord, it is absolutely necessary that it is a UL LISTED 3-wire grounding type appliance extension cord. The marked rating of the extension cord shall be 115 V, 15 A.
-
Page 10: Temperature Control & Humidity Adjustment
Temperature Control & Humidity Adjustment 1. Temperature Setting • Set the temperature at 55 • On initial start-up, the time required to reach the desired temperature will vary, depending on the quantity of bottles, temperature setting and surrounding temperature. • Allow 24 hours to stabilize the temperature for each new temperature setting operation 2. - Page 11 2.1 LED Functions MODE Flashing Flashing Flashing 3) Alarm Signals 3.1 Code Description MESSAGE CAUSE Temperature probe faulty High temperature alarm Low temperature alarm External alarm 3.2 Alarm Recovery Probe alarms P1”, start a few seconds after the fault in the related probe; they automatically stop a few seconds after the probe restarts normal operation.
- Page 12 5) Parameter Programming 1. Press the SET + keys for 3 sec until the “°C” or “°F” LED starts blinking, then release the keys. 2. Press again the SET + displayed, then release the keys. The first parameter Hy will be displayed. 3.
-
Page 13: Care Guide
I. Condenser Coil Cleaning • The condenser coil is on the ambient air intake side of the cooling unit. • Clean the condenser coil regularly. Coil may need to be cleaned at least every 6 months. • Unplug the cooling unit or disconnect power. •... -
Page 14: Troubleshooting
This Troubleshooting Chart is not prepared to replace the training required for a professional refrigeration service person, not is it comprehensive Complaint Possible Causes a. Power cord unplugged 1. Unit not b. No power to unit running c. Setting temperature d. - Page 15 Failed components a. Improper room insulation & seal 5. Unit running too long b. Exhaust restricted c. Room too large d. Ambient temperature higher > ° e. Dirty Condenser a. Post-compressor 6. Fan motor mode running but b. Incorrect power supply compressor c.
- Page 16 11. Evaporator a. Evaporator air flow restriction b. Not stopping due to air leak, high freezing up ambient setting c. Low ambient temperature d. Bad thermostat or sensor e. Moisture in the system f. Refrigerant low or leaking g. Capillary tube blockage a.
-
Page 17: Wiring Diagram
Wiring Diagram Fig. 6.1 WIRING DIAGRAM - 16 -... -
Page 18: Customer Support
Customer Support If you still have problems, please contact us at: Vinotemp International 17631 South Susana Road Rancho Dominguez, CA 90221 Tel: (310) 886-3332 Fax: (310) 886-3310 Email: info@vinotemp.com - 17 -... -
Page 19: Warranty
BTU/H. While every effort has been made to provide accurate guidelines, VINOTEMP can not warranty its units to cool a particular enclosure. In case of failure, VINOTEMP cooling units must be repaired by the factory or its authorized agent. Repairs or modifications made by anyone else will void the warranty. - Page 20 VINOTEMP will, at its discretion, repair or replace the unit and return it free of charge to the original retail customer. If the unit is found to be in good working order, or beyond the initial twelve month period, it will be returned freight collect.