Summary of Contents for VERDER Verderflex Vantage 3000 C Series
Page 1
Peristaltic Cased Tube Pumps Verderflex Vantage 3000 C Operating Manual EZ / S10 / R3i Version 2.0v-12/2013 Print No.
Page 2
Maintenance Version 2.0v-12/2013 Verderflex Vantage3000 C Print-No. 01 EZ / S10 / R3i The information in this document is essential for the safe operation and servicing of Verderflex Vantage3000 pumps. This document must be read and understood thoroughly prior to installation of unit, electrical connection and commissioning. FL-Auto control Verderflex Vantage 3000 C 2.0v-12.2013...
Maintenance Table of contents About the product Key features Warranty Pump returns ‘EC’ Declaration Safety Intended use Prevention of obvious misuse Maintenance Pump head options and installation Types of pump head EZ head 7.2.1 Key features 7.2.2 Installing the tube 7.2.3 Replacing the pump head 7.2.4 Stacking pump head S10 head...
Page 4
Maintenance Keypad Keys and symbols Symbol Meaning Symbol Meaning Start CW Counter clock wise Start CCW Clock wise Scroll up Caution Scroll down Set RPM Enter Press Press and hold down Maximum Stop Table 1 Keypad Keys and symbols FL-Auto control Verderflex Vantage 3000 C 2.0v-12.2013...
Maintenance Types of pump head Verderflex® Vantage 3000 pumps are available with the S10 pump head featured on the Verderflex Smart tube pump, as well as the R3i head featured on the Verderflex Rapide tube pump providing greater flow rates with stackable and multi channel head options.
Maintenance 7.2.3 Replacing the pump head – EZ head Offer pump head to backplate at angle locating drive shaft and rotor shaft with pump head at approx 45° to vertical, locating backplate lugs in housing. Push and twist until location lever clicks into position Remove by depressing location lever and twisting pump head counter clockwise 45°...
Maintenance S10 Head 7.3.1 Key features Taken from the Verderflex Smart tube pump design. The S10 includes a quick tube change, ergonomic design for ease of use. Flow rates up to 1,780 ml/min (28 US GPH) Pressures up to 2 Bar (29 PSI) ...
Appendix Remote Analogue/Digital Control An external Analogue/Digital control can be used to operate the Vantage 3000 C & P range. Suitable IP66 and RS232 connectors are available for external connections. Types of Remote control: Foot/Hand switch Analogue control: 0 - 10V D.C Remote potentiometer 4 –...
Appendix Analogue Connector: Connector Layout Figure 4: 25 way 'D' type connector Connector Description: FUNCTION FORWARD RUN INPUT REVERSE RUN INPUT 5 VOLT SUPPLY (to potentiometer) 0-5 VOLTS INPUT 4-20mA INPUT 0-10 VOLTS INPUT RUNNING OUTPUT (5V) STOPPED OUTPUT (5V) 16 to 25 0 VOLTS (internally connected to zero volts in the pump) Table 10: Analogue/Digital Connector Pins...
Page 14
Appendix 9.5.1 Connecting the foot switch Connect the footswitch to the port marked “Analogue” of the Vantage 3000. (Refer fig.5) Only the user can be aware of all conditions and factors present during installation, operation, and maintenance of a foot switch and surrounding work area. Therefore, only the user can determine which footswitches and which point-of-operation safeguards can properly be used in a particular application or work station.
Page 15
Appendix 9.6.1 Connecting analogue control systems: Connect the analogue control device to the Analogue port of the Vantage 3000 as shown in fig 3. Function Connection Clockwise Started CW Stopped CW Counter Clockwise Started CCW Stopped CCW IP 66 Remote speed control Speed control 0-10V d.c Potentiometer...
10 Declaration of conformity according to EC Machine Directive EC declaration of conformity according to machine directive, appendix II A VERDER Ltd., Unit 3 California Drive, Castleford hereby declare that the following machine adheres to the relevant EC directives detailed below Designation...
Page 17
Appendix Verderflex Vantage 3000 C 2.0v-12.2013 17 | P a g e...
Need help?
Do you have a question about the Verderflex Vantage 3000 C Series and is the answer not in the manual?
Questions and answers