Table of Contents
Advertisement
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
CB1200 PELLET INSERT APPLIANCE
MODEL: CB1200MI-MBK
CAUTION
Check building codes prior to installation.
•
Installation MUST comply with local, regional, state
and national codes and regulations.
•
Consult local building, fire officials or authorities
having jurisdiction about restrictions, installation
inspection, and permits.
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
1
Installation Manual
Installation & Appliance Set-Up
NOTICE: DO NOT DISCARD THIS MANUAL
R
If the information in these instructions is
not followed exactly, a fire could result
causing property damage, personal
injury, or death.
•
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
•
Do not over fire - If appliance or chimney connector
glows, you are over firing. Over firing will void your
warranty.
•
Comply with all minimum clearances to combustibles
as specified. Failure to comply may cause house
fire.
Hot glass will cause burns.
•
Do not touch glass until it is cooled
•
NEVER allow children to touch glass
•
Keep children away
•
CAREFULLY SUPERVISE children in same room as
fireplace.
•
Alert children and adults to hazards of high temperatures
•
High temperatures may ignite clothing or other
flammable materials.
•
Keep clothing, furniture, draperies and other flammable
materials away.
Tested and approved for wood pellets and corn pellets.
Burning of any other type of fuel voids your warranty.
To obtain a French translation of this manual, please contact
your dealer or visit
www.quadrafire.com
Pour obtenir une traduction française de ce manuel, s'il vous
plaît contacter votre revendeur ou visitez
7014-285C
WARNING
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
CAUTION
NOTE
www.quadrafire.com
August 1, 2018
Advertisement
Table of Contents
Related Manuals for Quadra-Fire CB1200
Summary of Contents for Quadra-Fire CB1200
- Page 1 INSTALLER: Leave this manual with party responsible for use and operation. OWNER: Retain this manual for future reference. NOTICE: DO NOT DISCARD THIS MANUAL WARNING CB1200 PELLET INSERT APPLIANCE MODEL: CB1200MI-MBK If the information in these instructions is not followed exactly, a fire could result causing property damage, personal injury, or death.
-
Page 2: Table Of Contents
G. Installation into a Masonry Fireplace ..13 H. Prefabricated Metal Chimney ....13 Quadra-Fire is a registered trademark of Hearth & Home Technologies. 7014-285C... -
Page 3: Important Safety Information
NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the ASTM E1509- 95, UL127, ULC S628-93, ULC S610-M87, ULC/ORD-C-1482-M1990, (UM) 84-HUD The Quadra-Fire CB1200 Pellet Insert meets the U.S. Environmental Protection Agency’s emission limits for pellet inserts sold after May 15, 2015. -
Page 4: Glass Specifications
CB1200 Pellet Insert C. Glass Specifications WARNING This appliance is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass. Please Fire Risk. contact your dealer for replacement glass. Hearth & Home Technologies disclaims any D. Electrical Rating responsibility for, and the warranty will be voided by, 115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps... -
Page 5: Getting Started
CB1200 Pellet Insert Install Guide Getting Started A. Design, Installation & Location Considerations Since pellet exhaust can contain ash, soot or sparks, you must consider the location of: 1. Appliance Location • Windows • Air Intakes NOTICE: Check building codes prior to installation. -
Page 6: Thermostat Wall Control Location
CB1200 Pellet Insert B. Thermostat Wall Control Location WARNING The thermostat wall control’s location will have some affect on the appliance’s operation. Fire Risk. • Maximum wire length from appliance is 100 feet Damaged parts could impair safe operation. Do (30.48m) continuous non-spliced wire. -
Page 7: Install Checklist
CB1200 Pellet Insert E. Install Checklist ATTENTION INSTALLER: Follow this Standard Work Checklist This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual. __________________________________________________________________________ Customer: ______________________________________________________________________... -
Page 8: Dimensions And Clearances
CB1200 Pellet Insert Dimensions and Clearances A. Appliance Dimensions 29-1/4 in [743mm] 22 in [559mm] 29-1/4 in [743mm] 8-3/4 in [223mm] 22 in [559mm] 8-3/4 in [223mm] 12-3/8 in 13 in [315mm] 10-7/8 in [330mm] 12-3/8 in [277mm] 13 in... -
Page 9: Clearance To Combustibles, Ul And Ulc
Part 811-0730, allow 1-1/2 inches (38mm). Figure 9.1 NOTE: A Quadra-Fire floor protector (Part 811-0730) is available through your dealer to be used as a floor protector for the section under the insert body only. Floor protection to front and sides of insert appliance must be supplied in addition to this part. -
Page 10: Minimum Opening For Masonry
CB1200 Pellet Insert C. Minimum Opening for Masonry & Zero Clearance Fireplaces TOP TRIM 19-3/4 in 19-3/4 in (502mm) (502m) 28-1/2 in (724mm) 18-1/4 in HEARTH (464mm) EXTENSION Figure 10.3 Figure 10.1 Note: If trim measurement is over 3/4 in (19mm) in depth MANTEL use mantle or side clearances to combustibles. -
Page 11: Floor Protection
Trim Ring * See Thermal Resistance: R value. Flex Hose Hose Clamp NOTE: A Quadra-Fire floor protector (Part 811-0730) is available through your dealer to be used as a floor protector for the section under the insert body Collar only. Floor protection to front and sides of insert... -
Page 12: Installation Into A Factory-Built Fireplace
CB1200 Pellet Insert F. Installation into a Factory-Built Fireplace The following is only one example as there are many different models of factory-built fireplaces. The following modifications are permissible: • Removal of damper or locked in open position NOTE: This example is for reference only. Any •... -
Page 13: Installation Into A Masonry Fireplace
CB1200 Pellet Insert G. Installation into a Masonry Fireplace 1. Secure the fireplace damper in the open position. If this cannot be accomplished, it will be necessary to All modifications that can be made to a Factory Built Fire- remove the damper place can be made to a Masonry Fireplace. -
Page 14: Vent Information
CB1200 Pellet Insert Vent Information A. Venting Termination Minimum Requirements Electrical Service Inside Corner FIXED FIXED OPEN CLOSED CLOSED OPEN J or K Figure 14.1 Termination Cap Restricted Area Air Supply Inlet Gas Meter All minimum clearances are listed with an Outside Air Kit (OAK) installed, unless otherwise noted in table below. -
Page 15: Avoiding Smoke And Odors
CB1200 Pellet Insert B. Avoiding Smoke and Odors Vent Configurations When installing a pellet appliance with a horizontal vent Negative Pressure, Shut-Down and Electrical Power configuration the frequency of power outages should be Failure considered: • Power outages during operation will cause the... -
Page 16: Negative Pressure
Avoid installing the appliance near doors, walkways or to 6 inch (76-152mm) Top Vent Offset Adapter, use Listed small isolated spaces double wall flue connector. A Quadra-Fire Outside Air Kit • Recessed lighting should be a “sealed can” design must be used with manufactured home installations. -
Page 17: Equivalent Feet Of Pipe
CB1200 Pellet Insert F. Equivalent Feet of Pipe G. Pipe Selection Chart The table below can help you calculate the equivalent feet The chart will help you in determining proper venting of pipe which is a method used to determine pellet vent size according to the equivalent feet of pipe calculated size (Figure 17.1). -
Page 18: Venting Systems
CB1200 Pellet Insert Venting Systems A. Full Reline With Outside Air - Horizontal WARNING Fire Risk. CAUTION Inspection of Chimney: • Masonry chimney must be in good condition. Never draw outside combustion air from: • Meets minimum standard of NFPA 211 •... -
Page 19: Full Reline With Outside Air - Vertical
CB1200 Pellet Insert B. Full Reline With Outside Air - Vertical NOTE: Check clearances carefully for this type NOTE: In Canada only a full reline is allowed per ULC of installation to ensure adequate room for S628, ORD ULC C1482-M1990. -
Page 20: Appliance Set-Up
CB1200 Pellet Insert Appliance Set-Up A. Rear Shroud Installation 2. Using a Phillips head screwdriver and two screws to Tools Required: attach Filler Bracket (Figure 20.3). Electric drill, #26 drill bit, Phillips screw driver, 3/8 inch wrench, and 7/16 inch socket wrench. - Page 21 CB1200 Pellet Insert 4. Install the left shroud panel corner; 2 screws into back 8. Assemble the right shroud panel corner and the right of hopper and 1 screw down into the filler piece (Figure shroud panel using 3 screws (Figure 21.5).
-
Page 22: Outside Air Kit Instructions
12. Using the electric drill with #26 drill bit; drill 2 holes into the left side of the hopper. Add two screws to secure NOTE: A Quadra-Fire outside air kit; 811-0872, is available shroud assembly to the appliance (Figure 22.1). -
Page 23: Adjustable Hopper Options
CB1200 Pellet Insert C. Adjustable Hopper Options E. Adjustable Hearth Support Depending on your installation, the hopper can be adjusted Size: 9”D x 45”W, 2” to 10” Height Adjustment down 2-1/2 inches (64mm) and will decrease in capacity from 75lbs to 60lbs. -
Page 24: Panel And Trim Set
CB1200 Pellet Insert F. Panel and Trim Set EXPLODED VIEW OF SCISSORS Standard Size: 30 inches H x 40 inches W (762mm x 1016mm) Large Size: 33 inches H x 50 inches W (838mm x SCREWS ARE CIRCLED 1270mm) Included in Kit: 2 side panels, 1 top panel, 2 side trim, 1 top trim, 2 corner brackets and fastener package. - Page 25 CB1200 Pellet Insert F. Panel and Trim Set (Cont’d) 5. Hold side curtains in open position and lower panel set over insert setting lower edge of top panel in slot between hopper lid and panel support as shown in Figure 25.5. Place existing screw head (installed in Figure 25.6) into locater hole in floor of insert.
-
Page 26: Thermostat Installation And Operation
CB1200 Pellet Insert G. Thermostat Installation and Operation The kit comes with a programmable wall thermostat and 25’ of thermostat wire. If you need to run more than 25’ make sure you use a continuous strand of 18 to 22 gauge thermostat wire. - Page 27 CB1200 Pellet Insert 1. Separate the body of the thermostat from the mounting CONNECT THERMOSTAT WIRES TO APPLIANCE: plate by gently pulling the two pieces apart (Figure There is a 4 screw terminal block located on the back lower 27.1) left corner of the stove directly above the power cord inlet.
-
Page 28: Optional Log Set Placement Instructions
CB1200 Pellet Insert H. Optional Log Set Placement Instructions CAUTION Logs are FRAGILE. Use extreme care when handling or cleaning logs. Place the front log in first as shown in Figure 28.1 charred area surrounding fire pot. Set the left and right logs onto the front log, placing the holes in the base of the left and right logs over the locating pins in the front log. -
Page 29: Mobile Home Installation
CB1200 Pellet Insert Mobile Home Installation You must use a Quadra-Fire Outside Air Kit 811-0872 CAUTION for installation in a mobile home. THE STRUCTURAL INTEGRITY OF THE MOBILE 1. An outside air inlet must be provided for the HOME FLOOR, WALL AND CEILING/ROOF MUST BE... -
Page 30: Reference Materials
CB1200 Pellet Insert Reference Materials A. Service & Maintenance List Date of Service Performed By Description of Service 7014-285C August 1, 2018... - Page 31 CB1200 Pellet Insert Date of Service Performed By Description of Service August 1, 2018 7014-285C...
-
Page 32: Accessory List
CB1200 Pellet Insert B. Accessory List 7014-285C August 1, 2018... - Page 33 CB1200 Pellet Insert August 1, 2018 7014-285C...
- Page 34 CONTACT INFORMATION Hearth & Home Technologies 352 Mountain House Road Halifax, PA 17032 Division of HNI INDUSTRIES Please contact your Quadra-Fire dealer with any questions or concerns. For the number of your nearest Quadra-Fire dealer log onto www.quadrafi re.com CAUTION DO NOT DISCARD THIS MANUAL •...