Technical Specification; Installation - Kohler COMPOSED K-20257T-B-CP Installation Instructions Manual

技术参数
电源：直流 4节5号碱性电池(LR06×4)
交流 电压220V,频率50/60Hz
检测时间：小于0.5秒
关阀延时：0.5～1秒
感应距离：自动调节
流量：
0.5GPM
约1.9L/min
0.35GPM 约1.4L/min
0.26GPM 约1.0L/min
超时用水控制：超时用水1分钟，自动止水。
环境温度：1 ～55
进水温度：0.5～71
适用水压：0.05～
安装步骤
如何安装水龙头
一 龙头与面盆的安装固定
将固定螺杆(2)安装到水龙头(1)底部
处。再把垫片(3)套在固定螺杆上。并
嵌入水龙头底部的盘槽中。然后将电
源线(7)和出水软管(8)穿过安装孔，
从面盆下方将固定橡胶垫片(4)固定金
属垫片(5)和固定螺母(6)对齐固定螺
杆向上套入。调整水龙头电源线及出
水软管的位置。用扳手拧紧固定螺母
以便把水龙头固定在面盆上。
二 安装控制组件
拧下控制盒盖(10)螺钉(11)，打开控制
盒(9)，根据安装尺寸图（图一）在墙
壁合适的位置钻孔，打入膨胀管
(12)，使控制盒紧贴墙面，再用螺钉
(13)将其固定在墙壁上。
注意：控制盒长边端需竖直放置，出
水口位置可根据需要左右调整。
对于冷热混水龙头，将软管(16)一端与
三通进水软管组件(17)连接，另一端与
控制组件(15)进水口连接，再将出水口
与龙头出水软管(8)连接，三通进水软
管组件另外两端与角阀(18)连接。
对于单冷龙头，将软管(16)一端与滤网
接头组件(19)相连，另一端与角阀连接
即可。
1359742-T01-A
℃
℃
6

TECHNICAL SPECIFICATION

Power: DC 4 pieces of AA size alkaline batteries
AC 220V, 50/60Hz
Senser Duration: Less than 0.5s
Shut-off Delay: 0.5~1s
Sensing Distance: Automatic adjustment
Flow Rate:
Overtime Flowing Control: Automatically stop flushing
when the faucet senses an object for more than 1 minute
continuously
Ambient Temperature: 1~55
Supply Water Temperature: 0.5~71
Supply Water Pressure: 0.05~0.86MPa
1
2
3
4
5
7
8
9
10
图一
13
12
0.5GPM About 1.9L/min
0.35GPM About 1.4L/min
0.26GPM About 1.0L/min
℃

INSTALLATION

How to Install the Faucet
Secure faucet on lavatory
1.
Install the stud (2) to the underside of the
faucet (1). Slide the gasket (3) over the
stud, and then seat the gasket in the groove
on the underside of the sprout. Cross power
cord (7) and water outlet hose (8) through
mounting hole, slide rubber washer (4),
metal washer (5) and nut (6) onto the stud
from under the sink. Adjust faucet power
cord and water outlet hose position, fasten
nut to secure faucet on lavatory mounting
surface by wrench.
Install Control Assy
2.
Unscrew valve cover screw (11) with a
screwdriver and open valve cover (10).
Determine proper mounting location per
11
rough –in (Fig 1), then punch expansion
tube (12) in. Place valve box against the
wall and then secure control valve
assembly on the wall by bolts (13).
Note: Place the long end of control box
upright, water outlet position shall be
adjusted left/right based on requirements.
For mixture faucet, connect hose (16)
to Tee water inlet hose assembly(17),
and then connect water outlet with
faucet water outlet hose (8). Connect
Tee water inlet hose other two ends
with valve (18).
For cold water faucet, connect hose
to the cylinder(19) and then connect
with valve.
℃
5