Related Manuals for mundoclima MVD D4+
Summary of Contents for mundoclima MVD D4+
- Page 1 High Pressure Duct Installation manual CL23187 to CL23189 English www.mundoclima.com...
-
Page 2: Table Of Contents
Installation manual High pressure duct D4+ If the supply cord is damaged, it must be replaced by the CONTENTS PAGE manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. INSTALLATION PRECAUTION..............1 INSTALLATION PLACE................1 An all-pole disconnection switch having a contact separation of ACCESSORIES..................2 at least 3mm in all poles should be connected in fixed wiring. -
Page 3: Accessories
Installation manual High pressure duct D4+ ● There is much evaporating acid or alkaline gas. The following are selectable accessories ● Other special areas. Remote controller & Its Frame ● Notes Before Installation 1. Remote controller........1 Select the correct carry-in path. ●... - Page 4 Installation manual High pressure duct D4+ Wooden construction The positioning of ceiling hole and indoor unit and hanging screw bolts Put the square timber traversely overthe roof beam, then install the hanging screw bolts. (Refer to Fig.4-1) routine method of installation: the size of installation for indoor unit following the Fig.4-6 and Fig.4-9 Timber over the beam Unit: mm...
-
Page 5: Installation Space
Installation manual High pressure duct D4+ 7. DUCT DESIGN NOTE During teardown and installation, the scroll was allowed direct Cover the pipe before connecting to keep rubbish, dust or other support by hand impurities out. Fan subassembly is more weightiness, please take careful Key points of duct connection during teardown and installation, and keep from hurt by fan subassembly. - Page 6 Installation manual High pressure duct D4+ Panel installation ● Fix the main body and the outside frame with the fix board of waist-shape hole (in two places). ● Unload inner frame. Slide the knob, release the buckle from the outside frame hole, Hang one side of the fix board of the waist-shaped hole on the then unload the inner frame.
-
Page 7: Install The Connecting Pipe
Installation manual High pressure duct D4+ 8. INSTALL THE CONNECTING PIPE Use frozen oil Check whether the height drop between the indoor unit and outdoor unit, the length of refrigerant pipe, and the number of Fig.8-1 the bends meet the following requirements: ●... - Page 8 Installation manual High pressure duct D4+ 9.2 Check The Leakage The necessary filling amount of refrigerant ● Refrigerant volume to be added is calculated according to Check all the joints with the leak detector or soap water. (See outdoor unit installation manual .Be sure to add refrigerant Fig.9-6 as a reference illustration) measuring by a scale.
-
Page 9: Connect The Drain Pipe
Installation manual High pressure duct D4+ 11. WIRING 10. CONNECT THE DRAIN PIPE Attaching wiring Install indoor unit drain pipe ● The air conditioner should use separate power supply with rated For 400 to 560 indoor unit, please use water connecting pipe and Adhesive tape for seal when connecting drain pipes. -
Page 10: Control
Installation manual High pressure duct D4+ Table.12-1 CAUTION For set horsepower ENC1 Toggle switch Capacity(Horsepower) Code The reserved function is indicated in broken line table,users can select it when necessary. 2200W(0.8HP) 2800W(1.0HP) Terminal board diagram 3600W(1.2HP) Please refer to the indoor unit wiring diagram for the detailed 4500W(1.5HP) Note: The horsepower wiring. - Page 11 Installation manual High pressure duct D4+ Mainboard codes indication label SW 5 Definition SW 1 Definition 00 means temp. compensation 1 means factory test mode value is 6 under heat mode 0 means auto addressing mode (default setting) 1234 01 means temp. compensation value is 2 under heat mode 1 means DC fan is chosen...
-
Page 12: Trouble Shooting
Installation manual High pressure duct D4+ 13. TROUBLE SHOOTING 15. INSTALL BRANCH PIPE Table.13-1 For 40KW~56KW models. NO. Type Contents LED Lamp flash Remarks Electric throttle part The evaporator Low-pressure pipe Hi-pressure pipe sensor check Run lamp After the malfunctions Malfun- point is abnoma flashes... -
Page 13: Test Operation
Installation manual High pressure duct D4+ 16. TEST OPERATION CAUTION The test operation must be carried out after the entire installation Protection function will delay the startup of compressor for 3 has been completed. minutes in case the unit is turned on immediately after power on or restarted after shutdown. - Page 14 ASK FOR MORE INFORMATION Phone: (+34) 93 446 27 81 eMail: info@mundoclima.com TECHNICAL ASSISTANCE Phone: (+34) 93 652 53 57 www.mundoclima.com...
Need help?
Do you have a question about the MVD D4+ and is the answer not in the manual?
Questions and answers