Table of Contents
Advertisement
Audio Settings
[SUBWOOFER SET]
[ON]: Turns on the subwoofer output. ; [OFF]: Cancels.
[FADER]
(Not applicable if 3-way crossover is selected.)
[R15] to [F15] ([0]): Adjusts the front and rear speaker output balance.
[BALANCE]
[L15] to [R15] ([0]): Adjusts the left and right speaker output balance.
[VOLUME OFFSET]
[–15] to [+6] ([0]): Presets the initial volume level of each source by
comparing to the FM volume level.
(Before adjustment, select the source you want to adjust.)
[SOUND EFFECT]
[SOUND RECNSTR]
(Not applicable for RADIO source and AUX source.)
(Sound
[ON]: Creates realistic sound by compensating the high-frequency
reconstruction)
components and restoring the rise-time of the waveform that are lost in
audio data compression. ; [OFF]: Cancels.
[SPACE ENHANCE]
(Not applicable for RADIO source.)
[SMALL]/[MEDIUM]/[LARGE]: Virtually enhances the sound space. ;
[OFF]: Cancels.
[SND REALIZER]
[LEVEL1]/[LEVEL2]/[LEVEL3]: Virtually makes the sound more
realistic. ; [OFF]: Cancels.
[STAGE EQ]
[LOW]/[MIDDLE]/[HIGH]: Virtually adjusts the sound position heard
from the speakers. ; [OFF]: Cancels.
[DRIVE EQ]
[ON]: Boosts the frequency to reduce the noise heard from outside the
car or running noise of the tyres. ; [OFF]: Cancels.
[SPEAKER SIZE]
Depending on the crossover type you have selected (see "Change the
crossover type" on page 7), 2-way crossover or 3-way crossover
setting items will be shown. (See the following "Crossover settings".)
[X ' OVER]
By default, 2-way crossover type is selected.
[DTA SETTINGS]
For settings, see "Digital Time Alignment settings" on page 24.
[CAR SETTINGS]
22
ENGLISH
• For 2-way crossover: [SUB-W LEVEL]/[SUBWOOFER SET] is selectable only if
[SWITCH PREOUT] is set to [SUBWOOFER]. (Page 6)
• [SUB-W LEVEL] is selectable only when [SUBWOOFER SET] is set to [ON].
Crossover settings
Below are the available setting items for 2-way crossover and 3-way
crossover.
SPEAKER SIZE
Selects according to the connected speaker size for optimum performance.
• The frequency and slope settings are automatically set for the crossover of
the selected speaker.
• If [NONE] is selected for the following speaker in [SPEAKER SIZE], the [X ' OVER]
setting of the selected speaker is not available.
– 2-way crossover: [TWEETER] of [FRONT]/[REAR]/[SUBWOOFER]
– 3-way crossover: [WOOFER]
X ' OVER (crossover)
• [FRQ]/[F-HPF FRQ]/[R-HPF FRQ]/[SW LPF FRQ]/[HPF FRQ]/[LPF FRQ]: Adjusts the
crossover frequency for the selected speakers (high pass filter or low pass
filter).
If [THROUGH] is selected, all signals are sent to the selected speakers.
• [SLOPE]/[F-HPF SLOPE]/[R-HPF SLOPE]/[SW LPF SLOPE]/[HPF SLOPE]/[LPF SLOPE]:
Adjusts the crossover slope.
Selectable only if a setting other than [THROUGH] is selected for the
crossover frequency.
• [SW LPF PHASE]/[PHASE]: Selects the phase of the speaker output to be in line
with the other speaker output.
• [GAIN LEFT]/[GAIN RIGHT]/[F-HPF GAIN]/[R-HPF GAIN]/[SW LPF GAIN]/[GAIN]: Adjusts
the output volume of the selected speaker.
Hide quick links:
Advertisement
Table of Contents
