For this reason, they may be different from the actual displays or faceplates. KENWOOD Remote Application ............13 • Operations are explained mainly using buttons on the faceplate. • English indications are used for the purpose of explanation. You can Bluetooth®...
Before Use IMPORTANT General: • Avoid using the external device if it might hinder safe driving. • To ensure proper use, please read through this manual before using this • Make sure all important data has been backed up. We shall bear no product.
Basics Faceplate Display window* How to reset Volume knob * Only for illustration purpose. On the faceplate Press B SRC. Turn on the power • Press and hold to turn off the power. Adjust the volume Turn the volume knob. Select a source •...
Getting Started Basics Remote control (RC-406) This unit can be remotely controlled with an optionally purchased remote control. Remote sensor (Do not expose to bright sunlight.) Pull out the insulation sheet when Select the display language, acknowledge the crossover using for the first time. type and cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], see page 7), the display shows: “SEL LANGUAGE” ...
Getting Started Default: [XX] Set the clock and date [AUDIO CONTROL] Press the volume knob to enter [FUNCTION]. [SWITCH PREOUT] (Applicable only if [X’OVER] is set to [2WAY].) (Page 7) Turn the volume knob to select [CLOCK], then press the knob. [REAR]/[SUBWOOFER]: Selects whether rear speakers or a subwoofer are connected to the line out terminals on the rear (through an external To adjust the clock...
Page 7
Turn the volume knob to select “2WAY” or “3WAY”, then press the For details on how to update the firmware, visit knob. <https://www.kenwood.com/cs/ce/>. • Once you have upgraded the firmware, you are unable to downgrade Turn the volume knob to select “YES” or “NO”, then press the knob.
Radio • To cancel, press or DIRECT. • If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled. Other settings Press the volume knob to enter [FUNCTION]. Turn the volume knob to select an item (see the following table), then press the knob.
USB/iPod Radio Connect a USB device [AF SET] [ON]: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor. ; [OFF]: Cancels. USB input terminal [TI] [ON]: Allows the unit to temporarily switch to Traffic Information if available (“TI”...
Page 10
USB/iPod Basic operations On the faceplate Random play Press 3 repeatedly. [FOLDER RANDOM]/[RANDOM OFF]: MP3/WMA/AAC/ WAV/FLAC file [SHUFFLE ON]/[SHUFFLE OFF]: iPod Press and hold 3 to select [ALL RANDOM].* * This does not work for iPod. Select music drive Selectable source: USB/iPod USB or iPod BT While in USB source, press 5 repeatedly.
Page 11
USB/iPod Skip search (applicable only for iPod USB source and iPod BT source) Direct Music Search (using the remote control) If you have many files in the selected list, you can perform the following to Press DIRECT. search for a file by skipping through the list at a rate selected in [SKIP SEARCH]. Press the number buttons to enter a file number.
USB/iPod You can listen to music from a portable audio player via the auxiliary input Alphabet search (applicable only for iPod USB source and iPod BT source) jack. You can search for a file according to the first character. Preparation: Press Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT]. (Page 6) Turn the volume knob to select a list, then press the knob.
KENWOOD Remote Application You can control the KENWOOD car receiver from iPhone/iPod touch (via Default: [XX] Bluetooth or via USB input terminal) or Android device (via Bluetooth) using [REMOTE APP] KENWOOD Remote application. • For more information, visit <https://www.kenwood.com/cs/ce/>. [SELECT] Selects the device ([IOS] or [ANDROID]) to use the application.
Bluetooth features may not work with this Press B SRC to turn on the unit. unit. Search and select the name of your receiver (“DPX-M3300BT”) on the • Be sure to turn on the Bluetooth function of the device to make the Bluetooth device.
Bluetooth® The following operations may differ or be unavailable depending on the Auto Pairing connected phone. When you connect iPhone/iPod touch to the USB input terminal, pairing request (via Bluetooth) is automatically activated if [AUTO PAIRING] is set to On the faceplate On the remote control [ON].
Page 16
Bluetooth® *1 This adjustment will not affect the volume of the other sources. Default: [XX] *2 Press and hold VOL to continuously increase the volume to 15. [SETTINGS] *3 Operations may vary according to the connected Bluetooth device. [AUTO ANSWER] [1] to [30]: The unit answers incoming call automatically in the selected time (in seconds).
Page 17
Bluetooth® Make a call using voice recognition [PHONE BOOK] (Applicable only if the phone supports PBAP.) 1 Turn the volume knob quickly to enter alphabet search mode (if the Press and hold VOICE to activate the voice recognition of the phonebook contains many contacts).
Page 18
To return to the previous setting item, press Press and hold “PLEASE PAIR YOUR PHONE PIN 0000” appears on the display. Default: [XX] Search and select the name of your receiver (“DPX-M3300BT”) on the [BT MODE] Bluetooth device. [PHONE SELECT] Operate the Bluetooth device to confirm pairing.
Bluetooth® Bluetooth — Audio On the faceplate • Operations and display indications may differ according to their availability Repeat play Press 4 repeatedly. on the connected device. • Depending on the connected device, some features may not work with [ALL REPEAT]/[FILE REPEAT]/[GROUP REPEAT]/ your device.
Audio Settings [MANUAL EQ] Adjusts your own sound settings for each source. • The settings are stored to [USER] in [PRESET EQ]. • The settings made may affect the current settings of [EASY EQ]. [62.5HZ] [LEVEL] [LEVEL –9] to [LEVEL +9] ([LEVEL +5]): Adjusts the level to memorize for each source.
Page 21
Audio Settings • For 2-way crossover: [SUB-W LEVEL]/[SUBWOOFER SET] is selectable only if [SUBWOOFER SET] [ON]: Turns on the subwoofer output. ; [OFF]: Cancels. [SWITCH PREOUT] is set to [SUBWOOFER]. (Page 6) [FADER] (Not applicable if 3-way crossover is selected.) (Page 7) •...
Display Settings Audio Settings – [SUBWOOFER] is selectable only when [SWITCH PREOUT] is set to [SUBWOOFER] Zone identification for color settings and brightness settings (page 6) and [SUBWOOFER SET] is set to [ON] (page 21). When 3-way crossover is selected: [TWEETER LEFT]/[TWEETER RIGHT]/[MID LEFT]/[MID RIGHT]/[WOOFER] –...
Connect to your vehicle’s steering remote harness. [DIMMER TIME]: Set the time to turn on dimmer and to turn off dimmer. Contact your KENWOOD dealer for details. 1 Turn the volume knob to adjust the [ON] time, then press the knob.
Installation/Connection Learning Steering Remote Control Press and hold any control keys on your steering remote control This section is for the professional installer. which you want to assign. For safety’s sake, leave wiring and mounting to professionals. Consult the A list of key functions will appear on the display. car audio dealer.
Page 27
Installation/Connection Basic procedure Installing the unit (in-dash mounting) Install onto the car brackets using the supplied screws (C) or (D). The screw Remove the key from the ignition switch, then disconnect the holes differ depending on the model of the cars. terminal of the car battery.
Page 28
Installation/Connection Installing in Toyota cars Connect external components Install onto the car brackets using the supplied screws (C) or (D). Use the mounting holes ( ) or ( ) that fit the car brackets. Then, install the supplied trim plate (A). Do the required wiring.
Page 29
Installation/Connection Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your Fuse (10 A) Antenna terminal car audio dealer. White To front speaker (left)/ If no connections are made, do not let the wire come out from the tab.
• Depending on the version of the operating system of the iPod/iPhone, some functions may not For: – Latest firmware updates and latest compatible item list operate on this unit. – KENWOOD original application – Any other latest information Preset color Visit <https://www.kenwood.com/cs/ce/>.
Troubleshooting References Change the display information Symptom Remedy Sound cannot be heard. • Adjust the volume to the optimum level. Each time you press DISP, the display information changes. • Check the cords and connections. • If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information (eg.
Page 32
Troubleshooting Symptom Remedy Symptom Remedy “UNSUPPORTED DEVICE” • Check whether the connected USB device is compatible “iPod ERROR” • Reconnect the iPod. appears. with this unit and ensure the file systems are in • Reset the iPod. • Press and hold B SRC to turn off the power. Turn the supported formats.
Specifications Troubleshooting Symptom Remedy Frequency Range 87.5 MHz — 108.0 MHz (50 kHz step) Sound is being interrupted or • Reduce the distance between the unit and the Bluetooth Usable Sensitivity 8.2 dBf (0.71 μV/75 Ω) skipped during playback of a audio player.
Page 34
Specifications Signal-to-Noise Ratio (1 kHz) 98 dB Maximum Output Power 50 W × 4 Full Bandwidth Power 22 W × 4 Dynamic Range 93 dB (at less than 1 % THD) Channel Separation 91 dB Speaker Impedance 4 Ω — 8 Ω MP3 Decode Compliant with MPEG-1/2 Audio Layer-3 Tone Action...
Page 35
Specifications • Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft. •...
Page 36
SOFTWARE LICENSE AGREEMENT Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be...
Page 37
Important Notice concerning the Software Article 9 Destruction of the Licensed Software If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed -jansson Software, any related documents and copies thereof within two (2) weeks from such date of termination. Copyright (c) 2009-2012 Petri Lehtinen <petri@digip.org>...
Page 38
-CMP sha2 AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/ The MIT License (MIT) Copyright (c) 2014 Charles Gunyon Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without You may obtain a copy of the license at limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the...
Page 39
Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved. T-Kernel 2.0 This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum Author: Chris G. Demetriou (www.tron.org) Permission to use, copy, modify and distribute this software and its documentation is hereby granted, BSD-3-Clause provided that both the copyright notice and this permission notice appear in all copies of the software, Copyright (c) 2000-2001, Aaron D.
Page 42
ﺍﻟﻤﻮﺍﺻﻔﺎﺕ • Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft. •...