HermanMiller Canvas Vista Installation And Disassembly For Recycling Instructions
Chase for workstations
Hide thumbs
Also See for Canvas Vista:
Advertisement
Quick Links
HermanMiller
Canvas Vista Chase Installation and
Disassembly for Recycling Instructions
How to assemble Canvas Vista Chase
Tools Required
Power Driver
Phillips Bit
Metric Socket
Hammer
Wrench
!
WARNING
All electrical connections to building electrical sources must
be made by a qualified electrician according to national, state
and local electrical codes.
!
WARNING
Disconnect power before installation. Failure to do so can
cause electrical shock and personal injury.
!
WARNING
Electrically interconnected units must be mechanically
interconnected.
HermanMiller
Safety Glass
Metric Allen
Wrench
Flat Blade
Screw Driver
Products Included
FG110
FG11A
FG292
FG144
FG157
FG156
FG2B1
L2CF
FG696
1
1BMJH0 rev B
FG150
FG160
FG119
FG117
FG121
FG141
FG154
FG152
FG2B2
FG2B3
L2CFS
Replacement Instructions
FG142
FG290
FGX10
Advertisement
Related Manuals for HermanMiller Canvas Vista
Summary of Contents for HermanMiller Canvas Vista
- Page 1 Products Included HermanMiller Canvas Vista Chase Installation and Disassembly for Recycling Instructions FG110 FG150 FG160 FG11A FG119 FG117 FG121 How to assemble Canvas Vista Chase Tools Required FG292 FG144 FG141 FG142 FG157 FG154 FG152 FG290 Power Driver Phillips Bit Safety Glass...
- Page 2 Canvas Vista Chase Installation Steps – Basic Configuration 2. Lay the bundle of data cables into the center cavity of the chase. 1. Position the Chase extrusions upside down on the floor in the approximate intended location. Place the Bottom Covers next to each Chase.
- Page 3 Install the two alignment pins into one of the chase ends. Tap the pins into the chase until the knurled area is completely inside the chase. HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 4 Loosely assemble the two nut plates to the top side of the top version of the end leg using the two M10 Screws. plate using the two M8 screws and the two long M8 hex bolts HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 5 Chase then tighten the M8 bolts to secure the harness. WARNING All electrical connectors must be fully engaged and locked. Loose connections can cause fire and/or electrical shock. HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 6 Harness Cover Harness Conduit Data Face plate Data Jacks Conduit needs to be routed between the wall of the harness cover and the sides of the data jack. Harness Conduit Data Face plate Harness Cover HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 7 2. Loosen the screw at the bottom of the yoke to allow the leg to move b. Leveling an A-Leg freely. Loosen it just enough to move the yoke to desired location. 1. Remove the two face screws. HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 8 14. Install the upper corner bracket on each of the Chase end legs. C. Smaller adjustments of ½” or les can be made using the glides at the bottom of the leg or foot. HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 9 16. If power is routed up the intermediate leg, install the Canvas Vista Chase Installation Steps – Storage Support (Two Types) intermediate leg power cover. This is an alternative support to the leg installation described in step 5 a.
- Page 10 The clamp will engage in the opening between the top panel and the side panel of the storage unit. Level the chase and check all joint to make sure that all joints are tight. HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 11 M8 screws. Separate the Top plate and inner extrusion from chase. the Bottom weldment of the storage support by removing the two M8 screws from the side of the storage support. HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 12 Pre-drill the holes in the top with a 1/8” diameter drill bit. Fasten the storage support weldment to the storage unit top with the self-tapping screws. HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 13 ½” increments and re-install the two bolts. HermanMiller 1BMJH0 rev B Replacement Instructions...
- Page 14 Canvas Vista Chase Installation Steps – Work Surface Support b. Locate the Post Leg using the pre-drilled holes in the work surface. Note that some of the required leg holes are pre-drilled In some configurations, the Chase attached work surfaces may be needed...
- Page 15 For more information about our products and services please visit us at hermanmiller.com or call (800) 851 1196. ©2019 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A. Part No. 1BMJH0 – B HermanMiller...