Wildix W01PRI Admin Manual
Hide thumbs
Also See for W01PRI:
- Quick installation manual (4 pages) ,
- Quick installation manual (5 pages)
Advertisement
Quick Links
W01-02PRI Installation Admin Guide - English
Jul 12, 2020 10:02
W01/02PRI Installation Admin Guide - English
This Admin Guide describes and explains how to connect and configure W01PRI and W02PRI media
gateways.
Created: June 2018
Updated: December 2019
Permalink:
https://confluence.wildix.com/x/5wGIAQ
Safety Recommendations and Location Requirements
Safety Recommendations
W01/02PRI Overview
Front panel
Rear panel
Installation of W01/02PRI
Using W01/02PRI on the Edge
Connecting the Telephony Cables
Connecting W01/02PRI using DHCP server
Connecting W01/02PRI using a static IP address
Configuration of W01/02PRI
Logging on to the PRI gateway Web Interface
Troubleshooting
LED Patterns
Reset of the Gateway
Partial Reset
Factory Reset
Disabling the Rescue Interface
Upgrading via single firmware file
Starting from PRI
(binary) file. If you have media gateways with version 42.2.XXX and lower, proceed with the following
steps:
1.
Manually upgrade devices to version 43.1.1264 (steps are described in
W01-W02PRI 2017
2.
Provision devices to PBX with WMS version 4.01.44392.36 or 3.88.44343.34 and higher (consult
Provisioning of Wildix devices Guide
3.
Within half an hour, media gateways are automatically updated to the latest firmware version
45.1.1870
Otherwise, skipping the upgrade to 43.1.1264 can lead to infinite transferring of configuration scripts.
W01-02PRI Installation Admin Guide - English
firmware
version 44.1.1605 and higher, upgrade is performed via single firmware
)
)
How to manually upgrade
Page 1 of 11
Advertisement
Related Manuals for Wildix W01PRI
Summary of Contents for Wildix W01PRI
- Page 1 W01-02PRI Installation Admin Guide - English Jul 12, 2020 10:02 W01/02PRI Installation Admin Guide - English This Admin Guide describes and explains how to connect and configure W01PRI and W02PRI media gateways. Created: June 2018 Updated: December 2019 Permalink: https://confluence.wildix.com/x/5wGIAQ...
- Page 2 W01-02PRI Installation Admin Guide - English Safety Recommendations and Location Requirements Safety Recommendations This equipment must be installed and maintained by service personnel. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous When the gateway is brought from a cold to a warm environment, condensation, that might be harmful to the device, may occur.
- Page 3 W01-02PRI Installation Admin Guide - English Behavior Condition Power Green, blinking, 1 cycle per second, Device is being restarted 50% duty Green, steady ON Device is restarted No current or failing power supply Ready Green, steady ON All lines are enabled (operational state) Green, steady OFF All lines are disabled (operational state) Blinking 1 cycle per 4 seconds, 75%...
- Page 4 W01-02PRI Installation Admin Guide - English Green 100 Mbps Yellow 1000 Mbps Switches Switch Description Reset/Default Allows setting the device to default (known) values. Refer to Reset of the Gateway Connectors and ports Connectors Description /ports SYNC IN 8 KHz TDM synchronisation pulse input SYNC OUT 8 KHz TDM synchronisation pulse output PRI port...
- Page 5 W01-02PRI Installation Admin Guide - English Connecting W01/02PRI using a static IP address Using W01/02PRI on the Edge Before You Start Your computer must be set to use the 192.168.0.11 private IP address Make sure that your network connection is working Steps: Connect a 10/100/1000 BaseT Ethernet RJ-45 cable into the ETH5ETH5/EXT Ethernet connector of the device...
- Page 6 W01-02PRI Installation Admin Guide - English Before you start: Your network interface must be set with an IP address in the 192.168.0.0/24 subnet (e.g. 192.168.0.11) You must use an IPv4 Network Make sure that your network connection is working Steps Connect a 10/100/1000 BaseT Ethernet RJ-45 cable into the ETH5ETH5/EXT Ethernet connector of the device Connect the other end of the cable into your PC...
-
Page 7: Troubleshooting
W01-02PRI Installation Admin Guide - English Click Login Troubleshooting Problem Cause Unable to contact the Management Wrong Eth port used for the Network configuration (Consult Using W01 Interface /02 PRI on the Edge or in the LAN with or without a DHCP server) Unable to contact the Management CLI service not activated in the configuration Interface via the CLI... - Page 8 W01-02PRI Installation Admin Guide - English Cancel an action that was started Revert to known factory settings if the device refuses to work properly for any reason or the connection to the network is lost Reconfigure the device The Reset/Default switch will generate different actions depending on the amount of time the button is held. Pressing Action Comment...
- Page 9 W01-02PRI Installation Admin Guide - English set the IP address to 192.168.0.1 and the Network Mask to 255.255.255.0 set the IPv6 link-local address on all network links. The IPv6 link-local address can be found underneath the unit A partial reset will also modify the following parameters to their default value: Service Parameter Default Value...
- Page 10 W01-02PRI Installation Admin Guide - English Wait a few seconds When all LEDs are blinking, but before they stop blinking, remove the paper clip Note: You have between 7 to 11 seconds. Result The Rescue Network Interface is displayed when accessing the Management Interface. Several parameters and services are modified.
- Page 11 W01-02PRI Installation Admin Guide - English Note: If you keep the Rescue Interface selected, you will not be able to get into the management interface after disabling it. Go to Network -> Interfaces In the Rescue Interface table, from the Activation selection list, select Disable Click Apply Result The unit will be reachable on the new static IP address configured.